How to disassemble a Dyson vacuum cleaner: clean it, remove the container, can it be washed under water, inside after cleaning

Thanks to the cyclone type of operation of Dyson vacuum cleaners, the device is capable of collecting not only noticeable debris and dust, but also bacteria.

After cleaning, the air in the room becomes clean, since all contaminants are deposited in a special container. But even such a high-tech device still requires care and cleaning.

What's included in the dyson v11 absolute pro

The Dyson V11 Absolute Pro kit is huge.
There are a dozen attachments and accessories for all occasions and situations; you don’t need to buy anything in addition. As I unpacked the small but massive vacuum cleaner box, my wife and I were constantly surprised: just when we thought we were done, there was another attachment, another accessory. It is impossible to fit it all in a second time from memory, the contents are so carefully placed.

I suggest you play the game. Try to find the entire contents of the Dyson V11 Absolute Pro box in the photo below.

If you count less than 13 items, try again.

The purpose of some attachments may seem duplicative, but in fact they perform different functions and are useful in different tasks.

1. Adapter for cleaning high and hard-to-reach places. It opens at any angle up to 180 degrees, allowing you to clean places where you would normally be unable to reach on your own. For example, you can use it to vacuum behind a cabinet or remove accumulated dust behind containers placed on the balcony.

2. A brush with stiff bristles. Good for car cleaning, dusting perforated and uneven surfaces, including heaters and wicker chairs.

3. Crevice nozzle. Essential tool for tight spaces between cabinets and in gaps at the headboard of a sofa. One of our most used for thorough cleaning.

4. Dock station for vertical installation of the vacuum cleaner. It is screwed to the wall using a special adapter, or attached to a strong double-sided tape. Allows you to charge the Dyson V11 Absolute Pro in an upright position by mechanically clipping it to the charger.

5. Combination nozzle. Can be used in two positions: with extended bristles and without them.

6. Main pipe. Not required, but most often used in conjunction with floor attachments.

It is not telescopic, which in other cases would be disappointing, but not when any attachment in the vacuum cleaner is replaced in literally two seconds.

7. Nozzle with a soft roller. The soft, two-tone bristles lift up small particles and dust, including stuck-on dust, from the floor, leaving surfaces cleaner than standard floor attachments on other vacuum cleaners.

It has its own mini motor with torque, which is powered by the vacuum cleaner battery.

8. Charger. Similar in size to the MacBook Pro adapter, made of plastic.

The cable length is about two meters, which is enough for convenient placement of the vacuum cleaner even without a docking station.

9. Mini electric brush. Suitable for hard-pile surfaces, upholstered thresholds and sofas.

The motor inside spins the brush, knocking out stubborn dust from the upholstery. It is most convenient to use it without a tube, with a direct connection to the vacuum cleaner.

10. High torque nozzle. Ideal for carpets with any length of pile, as it is adjusted mechanically using a switch at the front. It has several strips with brushes of different lengths and hardness, which not only clean out dust, but also unfasten stuck and previously detached pieces of lint.

The physical switch has three positions corresponding to the thickness and length of the carpet pile.

11. Brush with soft bristles. It is small and well suited for peripherals, for example, a laptop keyboard or the insides of a computer system unit.

12. Crevice nozzle with extension. It opens to almost twice its length, allowing you to reach the vacuum cleaner anywhere, especially in combination with the rotating nozzle and the main tube.

13. Miniature bristled crevice tool with extension. They didn't find it in the box right away. The purpose should already be clear.

This entire huge set more than covers any needs of the owner and outshines the equipment of our previous cordless vacuum cleaner, the Dyson V8. The ones we use most are the carpet, hard floor and crevice nozzle with extension, as well as the small combination nozzle. Together they cover 98% of typical home cleaning scenarios.

Preface

I love good technology, but I buy it very carefully. The market is full of premium devices that do not meet their own quality standards. Huge press attention is focused on smartphones and computers, which are examined almost under a microscope and criticize every detail. Household appliances rarely receive the same scrupulous attention.

I honestly admit: my wife and I bought our first cordless Dyson vacuum cleaner very carefully, having read dozens of reviews and interviewed friends who had dealt with Dyson before. Having found out everything about its capabilities, we finally decided. This happened more than two years ago, and to this day we only clean the apartment with him alone.

While I was personally pleased with the V8, there were a few inconveniences that remained, including the not-so-long runtime. The battery is still alive after 3 years, but this does not change the situation: cleaning was initially possible only for 25-30 minutes at minimum power. Often we had to hurry.

Therefore, the 60 minutes of operation of the Dyson V11 Absolute Pro on a single charge, as well as several other useful improvements already in the first days of testing, made the new model a complete upgrade over the previous one. I was also delighted with the kit itself.

How to increase the efficiency level of a home appliance

A device selected taking into account operating conditions will work effectively. Dyson produces 2 types of devices:

Cordless vacuum cleaners can be selected to clean home spaces of any size. A set of accessories allows you to vacuum any type of coating:

  • hard;
  • carpet;
  • delicate, including parquet;
  • carpet

This device is suitable for pet owners, especially long-haired ones. The quality of purification of the air entering the cyclone allows people suffering from allergies to lead a normal life.

We suggest you familiarize yourself with Soda for cleaning the washing machine from scale, dirt and unpleasant odors, reviews

Compact dimensions allow you to use the device in a car.

Cylindrical ones are not intended for cleaning delicate surfaces, and they are inconvenient for vacuuming cars.

In order for a household device to work efficiently, a number of rules must be followed:

  1. Choose the right vacuum cleaner from the proposed model range, taking into account all the tasks that need to be solved with the help of the device.
  2. Use recommended attachments to clean the surface.
  3. If there is a suction power switching system, adjust it depending on the type of cleaning to be done.
  4. If you need to provide clean air for a child or a person suffering from allergies, then with low suction power, Hepa filters are more effective.
  5. Do not allow moisture to get inside the device. Dry all washable parts thoroughly.
  6. Do not allow household appliances to be near an open fire or heating device.
  7. To ensure safety, do not use a vacuum cleaner on wet surfaces.

How to increase the efficiency level of the device?

  1. If the suction properties of the vacuum cleaner deteriorate, check how full the dust container is and remove debris from it. Also, the need to clean the container is indicated by a change in the noise emitted by the device during operation.
  2. During the cleaning process, take short breaks in the operation of the device to prevent possible overheating of the engine (the equipment should operate continuously for no more than 2 hours).
  3. Do not put pressure on the tube and the brush attachment, pressing it to the floor: this will limit the access of air into the vacuum cleaner and the motor may overheat.

When using a vacuum cleaner, strictly follow the operating instructions for the device specified by the manufacturer in the instructions.

If your device is not equipped with a dynamic load sensor system that automatically adjusts the engine speed, set the required power mode to clean different types of surfaces (smooth floors, carpets, rugs).

How to wash a Dyson vacuum cleaner | chistim-chistim.ru

After several years of using a Dyson vacuum cleaner, even if you follow the instructions, the suction power of the device decreases. Is it possible to wash a Dyson vacuum cleaner? The fact is that the manufacturer prohibits opening the upper cup, including the aerodynamic cone system, during the warranty period. This is where the cone can become clogged or the gasket or rubber seal can break. Even service centers are wary of disassembling this unit, explaining that it is not repairable. You can visually see compacted dust in the labyrinths, which reduces hydrodynamics. Nobody forbids washing the bowl or container with a fine filter. It is important that there is no moisture left in the assembly, which will short-circuit the motor winding and become a breeding ground for bacteria.

You can watch the video about how and why you may need to wash your Dyson vacuum cleaner. Slowly and clearly, the author disassembled the cyclone unit down to the screw and showed the problems after 4 years of operation of a household cyclone vacuum cleaner.

How to wash a Dyson vacuum cleaner without violating the manufacturer's requirements? For washing, use cool running water without detergent solutions. Surfaces must first be cleaned as dry as possible. Any operations on the device are carried out after the battery capacity is exhausted or disconnected from the mains power. Of course, from time to time you need to wash the receiving bowl, the vacuum cleaner canister in which the glass with the HEPA filter is installed, and the filters themselves with running water. With the top cover and drainage hatch open, this is easy to do. Transparent structures are washed until shiny using a high-pressure water jet.

When washing the pipes, you must remember that even a wet aerosol entering the engine will cause expensive repairs. Is it possible to wash a Dyson vacuum cleaner under water? This method will lead to the closure of wet contacts, soggy dirt in the cyclones, bricking up the holes and nipples of small cyclones.

Cleaning the cylindrical HEPA filter installed in the center of the cyclone of the Dyson vacuum cleaner is prescribed in the manufacturer's instructions. After repeatedly washing the soft seamless fiber, it is dried like a regular cloth, flattened for two days. The motor filter of a Dyson vacuum cleaner is more difficult to remove. It is installed under the canister or in the ball, a tool is required for disassembly. A solid plate in a rubber frame is washed with water under pressure, with sharp shaking. The plate is also dried for 48 hours.

During water procedures, you need to pay attention to the integrity of the rubber seals, plastic cone and glass. If necessary, replace defective components.

The outer side of the structure is cleaned with an antistatic cloth to remove static charge, which prevents the removal of electrified dust and hair. There is no need to wash the body with water to prevent drops from getting inside. Wipe the corrugated hose with a damp cloth and make sure that the drainage chambers are clean, or remove the contents with a small spatula and brush.

After all water and alcohol procedures, the disassembled vacuum cleaner is left for ventilation, assembled and put into operation after 48 hours. Nozzles and brushes are cleaned dry using a toothbrush, a flat hard brush, a knife or scissors, or a textile tourniquet.

Causes

There are 3 reasons why a vacuum cleaner stinks when working, which can be indicated by the type of smell:

What to do about the burning smell

A slight spark in the vacuum cleaner motor is normal. But if it sparks excessively and there is a burning smell, the problem is the failure of the brushes or the electric motor itself. As a rule, in addition to the burning smell, this is indicated by the loss of power of the vacuum cleaner, its constant overheating and interruptions during operation. What can be done in this case? Replace parts with new ones or repair and adjust existing ones. In any case, you need to know the possible causes of sparking:

Vacuum cleaner motor

Vacuum cleaner motor rotor

Thus, the vacuum cleaner sparks and smells unpleasant due to:

How to replace individual parts? To do this you need:

What to do about the smell of plastic

More often, inexpensive vacuum cleaners made in China emit a plastic smell. After a few days, or at most a month of active use of the vacuum cleaner, the smell should disappear on its own. In order not to wait for this, you can take special fresheners for the vacuum cleaner and suck them through the dust collector while cleaning.

What to do about the smell of dust

The smell of dust, on the contrary, appears after prolonged use of a household appliance. Most likely, its causes lie in excessive contamination of the garbage bag and (or) filter, or rather in the bacteria that settled there during cleaning and began to multiply. There are several ways to solve the problem:

Reusable dust bag

Freshener for vacuum cleaner in granules

To prevent the appearance of an unpleasant odor, it is necessary to empty the contents of the garbage bag and clean the filter after each cleaning. But these operations only delay the moment when bacteria literally “capture” both the filter and the bag.

Read about how you can clean your apartment without using a vacuum cleaner here.

Vacuum cleaners are characterized by constant suction power, which does not depend on the fullness of the garbage container. But for the smooth operation of the home assistant, it must be periodically disassembled and cleaned.

How to wash the outside and inside after cleaning?

The algorithm for cleaning cyclone devices is similar to cleaning other vacuum cleaners:

  • disconnect the device from the power supply;
  • disassemble the vacuum cleaner after studying its operating instructions;
  • wash all removable elements;
  • remove the rear engine cover, remove dust from the engine;
  • assemble the device, turn it on and check its operation.

IMPORTANT! It is strictly unacceptable to wash the parts of the vacuum cleaner with hot water and hard sponges. It is also prohibited to use preparations containing acids or alkalis to remove contaminants. Abrasive products can damage plastic components of household appliances.

We invite you to familiarize yourself with the Secrets of quickly and safely drying things after washing

Engine care rules

It is not recommended to clean the motor yourself at home. It is best to entrust this procedure to service center specialists.

In order to remove dust from the motor, you need to:

  • tighten the bolts on the device body;
  • remove the dust collector and open it;
  • remove dust from parts using a brush;
  • clean the board.

Important! The integrity of the elements and the location of the wires must not be violated.

How often can you wash a household appliance?

Cleaning a Dyson vacuum cleaner depends on the frequency of use of the device and the type of debris being removed. After treating surfaces where flour or other small debris has been spilled, the filters must be washed immediately.

The waste container is emptied when it is filled to the Max level. But it should be borne in mind that the remains of wool and household waste are a favorable environment for the proliferation of microorganisms. If the vacuum cleaner will not be used for a long time, it should be washed thoroughly.

Useful video

This video will show you how to disassemble and clean a Dyson vacuum cleaner:

Any instrument requires care to remain functional. When using a Dyson vacuum cleaner to clean your home, you should know how to clean the device from the collected dirt. The internal labyrinths and cavities are gradually clogged with a thin suspension, and the suction power decreases. Systematic care of the device will extend its service life.

How often can you clean a household appliance?

The device is equipped with a dust container, which should be emptied every three cleanings, even if it is not yet full. If, after using the device once, a lot of debris has accumulated in the dust collector, be sure to shake it out.

Wired and wireless models are equipped with two preliminary and final cleaning filters: the first product must be washed at least 1-2 times a month.

Fine filters, depending on the material they are made of, can be:

  • Reusable - made of fluoroplastic fibers filled with activated carbon. Such devices can be washed as they become dusty.
  • Disposable - made of paper, fiberglass with antimicrobial impregnation. You cannot blow air or place the filter in water to remove dirt - the product will be deformed and lose its properties. If dust accumulates in the device, it should be replaced with a new one.

IMPORTANT! Disassemble the device and remove dust from its internal surfaces at least once every six months. If you often use a vacuum cleaner, carry out this procedure once every three months.

Cleaning

Compared to the previous model, the V11 container has been enlarged by 40%, allowing for less frequent emptying. With the help of a convenient mechanism, you can remove waste from the vacuum cleaner directly into the waste basket as hygienically as possible during downtime.

To empty the dust bin, you need to move the red handle all the way down, then the lid will swing right over the trash can. The dust collector cup can be completely removed and wiped.

The vacuum cleaner itself informs you about the need to clean the filters by displaying a corresponding notification on the display. Then the filters can be removed and simply washed with cold water. The manufacturer recommends performing this procedure at least once a month

It is important to completely dry the filter before the next use: to do this, place the washed filter in a dry place with good ventilation for 24 hours and check it before installing it in the vacuum cleaner.

Recommendations for proper cleaning of the vacuum cleaner

A person washing a Dyson vacuum cleaner should follow the following algorithm:

  1. De-energize the device by disconnecting it from the power source.
  2. Remove the nozzle and, having disconnected the roller, clean the brush from the vacuum cleaner. Then wipe it with a damp cloth.
  3. Inspect and wipe the hose or tube, remove blockages.
  4. Empty the contents of the cylinder into a trash bag.
  5. Remove the container of the Dyson vacuum cleaner, rinse with cold running water and, after wiping with a napkin, leave to dry.
  6. Remove the filters and, after washing them under running cold water, place them to dry.
  7. Inspect the gaskets and carefully rinse the cyclone with running water without immersing it in water.
  8. Dry the parts for 48 hours. The occurrence of an unpleasant odor can be directly related to increased humidity of filters and internal parts.
  9. After inspecting all components for damage, reassemble the device in proper order.

Sometimes the question arises why the Dyson vacuum cleaner does not suck up debris. The cause may be a blockage in the cyclone; this is most often accompanied by heating of the device and its shutdown.

In this case, you should carry out extraordinary cleaning of the device. The Dyson mechanism is different in that the suction power does not depend on the level of debris in the container and is constant throughout the cleaning process.

If your Dyson vacuum cleaner runs jerkily, the reason may be that debris has gotten into the restrictor valve hinge. Simply disconnect the hose and manually remove the blockage.

General information

The laws of physics cause dust to settle on the walls of the bowl. The motor is protected by a washable filter. In addition to convenient disposal of the container, the advantage of such a system is that the power of the vacuum cleaner does not depend on the amount of debris it absorbs. Dyson vacuum cleaners are not so widely known in Russia, since they do not have aggressive advertising in this market. However, Dyson vacuum cleaners belong to the innovative premium segment.

The Dyson range consists of 16 vacuum cleaners. More precisely, these devices bear little resemblance to conventional vacuum cleaners. All of them are very compact in size and weigh less than 2 kg. They are also combined with a lithium-ion battery and a charging station, which allows you to clean the waste container with one button without disconnecting the attachments. The rotating anti-static brush is not unique to Dyson, but is present in all of their models.

Modern trends... in the vacuum cleaner!


Everything about my new house dust collection device is great. It seems that Dyson is trying to collect all modern technological trends in its devices. Although, the company rather asks them (as Wikipedia suggests).

When I received the package with the V8 and read all the characteristics in detail, I felt a little uneasy. The fact that the vacuum cleaner has a processor that controls the motor is in the spirit of modern gadgets. This is very cool, but expected. Still, Dyson's 6,000 engineers don't do nonsense. But a nickel-cobalt-aluminum battery! It's like Tesla cars - only very small. But just as capacious.

Thanks to the successful combination of a battery with high current output and a brutal motor, the suction power is as much as 22 aerowatts (aW) in standard mode and 115 (4 times more!) in afterburner. How much it? Enough to pick up regular dust and dry dirt from the floor using the Fluffy Basic Soft Roller Brush.

If the power seems insufficient, there is no need to increase the power. Dyson engineers have provided a brush with its own electric motor. It really increases the suction power! You can use it to collect even fine dust, such as flour or cement (collect it at your own peril and risk - you may lose the warranty).

We invite you to familiarize yourself with Hibiscus indoor care at home


I’ll just keep silent about the fact that it copes well with any dirt on fluffy surfaces. And I don’t know where those long blonde hairs came from on the floor... Other vacuum cleaners only extracted dust from this carpet.

Why then use turbo mode if everything can be assembled just like that? This thought hovered in my head exactly until the battery caught my eye. As soon as I applied the crevice nozzle to the cracks in the bimetallic radiators, the container was almost completely filled with dust. Otherwise, you won’t be able to get it out of there even with a rag (and this is not a man’s job).

Manufacturability in details


Power and equipment are not everything. The coolest thing about my allergies is that Dyson vacuum cleaners have recommendations from the British Foundation for People with Allergic Diseases, the Institute of Immunology of the Ministry of Health of the Russian Federation and the Moscow Research Institute of Pediatrics and Pediatric Surgery of Rosmedtekhnologii. You guessed correctly - about the benefits of using vacuum cleaners of this brand to combat allergies. Just a week later the effect began to be felt: the eternal runny nose disappeared.

They apply to the compact Dyson V8 in the same way as to the V6. 15 tiny cyclones separate the air in the can from the collected dust using a patented 2 Tier Radial™ design and force it through a filter system. It purifies the air no worse than a specialized device. No smell of dust, no noise. (According to marketers, the vacuum cleaner filters particles down to 0.3 microns - and I am inclined to believe them).

Reading reviews of the previous generation of portable Dysons, I was afraid that the new vacuum cleaner would squeal like Sarah Jane Ferridge or Marika Schonberg. But no. The company's engineers did a tremendous job.


I did not hear any high-frequency howls during testing and subsequent operation. The sound is similar to the quiet rumble of an old Cadillac - impressive, bassy and very quiet compared to all vacuum cleaners I know. Very nice. You close your eyes and it’s like you’re driving a muscle car. This effect was achieved through a sophisticated system of soundproofing elements.

Even the cabin of a passenger plane would be envious of this. There is a special casing for the entire engine compartment. There is a filter at the outlet of the garbage disposal. And even in front of the air release valve there is its own filter!

Unique Apple-like design


What can we say - Dyson has its own signature style. When you walk through a consumer electronics store, your eye always stops at vacuum cleaners of this brand. They look among ordinary vacuum cleaners like a spaceship in a medieval port. Very cool - turbines, metal, shine. Usually, when disassembling such devices, you get the impression that you are looking at a short stump of something larger. But this particular vacuum cleaner is very cool even without the pipe, turning it into something like a scooter from Star Wars.

When the V8 hangs in its base on the wall, the resemblance to a spaceship only intensifies. Who would have thought that such a prosaic device as a vacuum cleaner looks like a rocket on the launch pad?

However, not a single element of the Dyson V8 stands out. The design and appearance are laconic. Harmony of technology and design, in a word. It seems that the company's engineers have a connection with the Cupertino developers. In my apartment, where the iPad and iPhone are the basis of style, the Dyson V8 looks great. I can't imagine anything cooler.

Pairs perfectly with Apple technology. With any modern technology.

Pros and cons of the Dyson V8

The British development of Dyson v8 has significantly more design and operational advantages than disadvantages.

One of the clear advantages of the model is the contactless disposal of collected waste. The container is simply placed above the waste bin, after which the user opens the lower flap with one movement of the lever

If we rely on the practical use of technology, we can confidently highlight the following advantages:

  • a wide range of attachments;
  • sufficient suction power for this class of models;
  • When operating in normal mode, the noise level is low;
  • comfortable, sufficiently sized handle-bar;
  • convenient design of the waste collector for controlling accumulations;
  • effective cyclone filter;
  • beautiful appearance.

Meanwhile, despite the unique design and innovative design “tricks”, the device is still not without its drawbacks.

One of the obvious disadvantages of the model is the wear and tear of plastic parts over time. This is what the container body looks like (worn, cloudy plastic) after a certain period of operation.

The number of disadvantages, of course, cannot be compared with the number of advantages, but they are there:

  • increased noise when operating at maximum power;
  • sensitive heating of the case at maximum power;
  • Most of the parts are plastic.

Another disadvantage that causes complaints from many owners is the very limited cleaning time (7 minutes) in the “Turbo” mode. However, they note that this option is used extremely rarely.

In the Dyson product line, the V8 model is not the only representative of the wireless technology class. If you are looking for a cordless vacuum cleaner, we recommend that you familiarize yourself with this rating.

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]