Cleaning agent for hot tubs, how to care for and disinfect

A hot tub allows you to relax your muscles, improve your skin condition and relieve stress after a working day. In order for your home Jacuzzi to remain functional, you need to regularly care for the surface and monitor the condition of the pipes and pump.

Caring for your hot tub includes cleaning the filters and removing surface contaminants.

The rules for cleaning a Jacuzzi depend on the material from which the coating is made - acrylic, marble, cast iron or steel.

Annual cleaning

Professionals recommend annual cleaning with acetic acid.
This method gets rid of mineral deposits, all types of fungus and mold. What to do:

The Jacuzzi is filled with water above the top jets.
Then pour 1 liter of acetic food acid.
Turn on the pump for 1 minute.
Then it is turned off, and the liquid is left in the bowl for 12 hours.
After this time, drain the water, add clean water and turn on the pump for 5 minutes. During this time, all internal parts will be washed.

At the end, the Jacuzzi is turned off, the waste liquid is turned off and the surface of the bowl is rinsed with clean water.

Why is cleaning necessary?

The hydromassage system consists of a pump, compressor, pipes, nozzles and check valves. Hoses leading to the bathtub supply water, and parts inside the jacuzzi shape and direct the jets.

During operation, impurities from the water gradually settle on the surface of the pipes. High humidity and temperature promote the development of mold. Pathogenic microorganisms (fungi, bacteria) form durable biofilms that clog nozzles and nozzles. Dirt and mold are removed from the system using professional or home remedies.

Irregular cleaning can lead to the following consequences:

clogging of pipes, pump failure due to overload;
weakening of the jets, disruption of the hydromassage;
the formation of plaque on the surface of the bath;
contact of pathogenic bacteria and fungi on the skin and mucous membranes of users;
the appearance of an unpleasant odor in the bathroom.

Cleaning is necessary to avoid clogging of pipes.

How to clean your pipe yourself

A Jacuzzi massage system consists of a pump and a set of pipes that supply water to a container. With prolonged use, they become covered with plaque and biofilms, which cannot always be removed using household chemicals.

To check and service the hydromassage system you must:

remove the screen that covers the space under the bathtub;
study the dismantling instructions, photograph or write down the order of connecting the tubes;
loosen the nuts and remove the hoses where possible;
wash the dismantled parts with running water, rinse the internal dirt filters;
if the inner surface of the tubes remains slippery, soak them in a special solution for a Jacuzzi, and then clean them with a brush;
reassemble the system in reverse order;
Check the tightness of the connections by wrapping them in toilet paper and turning on the hydromassage.

Remove the screen and wash the dismantled parts.
If individual tubes are very clogged, you can clear them using a thick wire wrapped in damp gauze.

Cleaning products made from scrap materials

Not everyone trusts chemical cleaning products. In some cases, they can lead to detrimental consequences for acrylic. Sometimes the cost of products is beyond the buyer's means. Or the user is allergic to chemicals. In such cases, the cleaning agent can be prepared according to folk recipes, using available products, most of which are in the kitchen of any housewife.

Lemon acid. This recipe is designed to combat limescale. The acid packet is dissolved in hot water, after which the liquid is added to the bathtub filled to the overflow hole. After 2 hours, the water is drained and the bath is rinsed with plenty of clean water. Remaining moisture is removed with a soft cloth.

Folk remedies - vinegar, soda and citric acid - can overcome almost all contaminants in an acrylic bathtub

Toothpaste. Some simple stains can be removed with toothpaste. Rub the contaminated surface and rinse with clean water. The paste will not only remove the stain, but will also restore the acrylic’s former shine.
Soda. Rust that has not yet penetrated deeply into the acrylic surface can be removed with baking soda. To do this, it is diluted with water and applied to the stains. Rubbing the surface is strictly not recommended; friction can lead to the formation of scratches, which will further aggravate the situation. After 15 minutes, the soda paste is washed off.

There are many more ways to clean acrylic from stains, but the best of them is prevention. Avoid plaque deposits. Rinse your bathtub every time after use and your bathtub will remain sparkling clean for years to come.

Features and choice of detergents for different surfaces

The choice of cleaning products for a hot tub depends on the type of coating. Its surface can be plastic (acrylic), marble, cast iron or steel.

Acrylic coating

Acrylic is the most common material for hot tubs. Its advantages are corrosion resistance, light weight and low price. Plastic sheets are easily shaped, so acrylic bathtubs can have any shape.

At the same time, scratches easily form on the surface of polymethacrylate; the material is vulnerable to alkalis, acids, solvents, chlorine bleaches and ammonia. For daily cleaning, it is best to use liquid products that dissolve in water. To remove plaque, you can treat the surface with gel or cream for acrylic baths.

Acrylic is a well-proven material.

Products used for cleaning:

Bath Prosept Acryl;
B&B Unicum;
"Akrilan";
"Sanfor Acrylight".

If there is no special composition, you can use liquid soap, shower gel or dishwashing liquid.

It is not advisable to apply Domestos, Sanox and similar products to acrylic.

Cast marble surface

Cast marble is an expensive but durable material for a bathtub. When treated regularly, this coating repels dirt and water, so home remedies are sufficient to clean it: grated laundry soap gel, liquid soap, etc. The most stubborn stains are removed using toothpaste without abrasive components.

The following professional compounds are suitable for caring for marble surfaces:

Akemi;
Mellerud;
HG (cleaner and polish for natural stone).

Cast marble is environmentally friendly.
To clean marble, you cannot use gels with solid mineral particles (Comet, Pemolux, etc.) or acids. It is acceptable to use white vinegar diluted in water in a ratio of 1:1 or 1:2.

After cleaning, the bathtub is thoroughly rinsed and dried. To add shine, a small amount of polish is applied to the marble. The treated surface is wiped with a suede cloth.

Cast iron bath

Cast iron bathtubs are heavy, but they last a long time and retain heat well. The surface of the bowl is protected from corrosion by enamel.

The following products are used to clean a cast iron Jacuzzi:

Mr. Muscle for baths;
comet;
Cif Ultra White and Cif Active Fresh creams, Cif Power&Shine spray;
“Cillit Bang Anti-plaque and shine”;
"Sanox";
"Whiteness";
Bath and shower cleaner Frosch.

Cast iron bathtubs are the most reliable, strong and durable products.

To add shine to the enamel, you can use any composition that is suitable for paint and varnish coatings: for example, car polish.

Before final treatment, wipe the surface with a towel and paper napkin. Spread the polish over the enamel with a microfiber cloth. When the surface begins to shine, the bath is rinsed with water and wiped dry again.

Steel coating

For steel baths, the same products are used as for cast iron. Enameled surfaces withstand the effects of weak acids, hydrogen peroxide, turpentine, chlorine and ammonia. For cleaning, you can use sponges with an abrasive side, but not steel wool or brushes.

The steel coating withstands acids well.

To remove rust and plaque, you can use undiluted table vinegar. Aggressive acids (for example, oxalic acid) damage the enamel coating.

How to Clean the Pipes in a Hot Tub

When buying any item, especially one with a mechanism, you should carefully consider the operation of such things. A Jacuzzi or hot tub is quite common. And I am very interested in the question of cleaning this product, because untimely procedures can lead to rapid wear of parts, and most importantly, to malfunction of both one element and the entire system as a whole.

Cleaning the tank

To make the cleansing process easier, the Jacuzzi should be rinsed after each procedure. To do this, you can simply rinse or wipe with a soft cloth and detergent. By the way, the liquid should be as gentle as possible and not contain acids or other aggressive components. You can use a specially formulated solution to clean your hot tub. This would be an ideal option because it does not foam too much and does not clog the pipes in the hot tub, which we will talk about cleaning later. However, using solutions every day is not recommended.

Basic cleaning and maintenance should be done once a month. To do this, you first need to fill the tank with water. Moreover, water should cover all nozzles of the system. After this, you need to add a little disinfectant solution to the water. It is commercially available or you can prepare it yourself. To do this, it will be enough to pour a weak chlorine solution into the tank, approximately 10-15 ml per liter of water.

After this, you need to turn on the system. The pumps should run for just a few minutes. Then they turn off and wait for 20-30 minutes, after which the water can be drained. But that’s not all, then you need to take the same amount of clean water and repeat the procedure.

Cleaning tubes and filters

Here you need to take into account the model of the jacuzzi, so saving the operating instructions is mandatory. It tells you how to remove the filters. The same goes for the tubing in your hot tub. After all, from the inside it is a whole complex of tubes of different diameters. Corrugated polymer products are most often used because they are more flexible, which is necessary for the shape of the tank. These tubes, thanks to their smooth inner coating, do not collect plaque and dirt inside, but they need to be cleaned periodically.

So, in order to clean the tubes efficiently with your own hands, you need to remove them in those places where this is possible. But, again, without instructions, and sometimes photos of additions to it, it is strongly not recommended to touch anything yourself, because incorrect dismantling and connection can lead to damage, which will be quite noticeable during repairs.

After some pipes have been removed, they can be cleaned under water pressure, even without using a special product. The only point is that the pressure must be strong enough. The same procedure is performed in cases where they are clogged. Although it is worth noting that this is very rare, and if the tank is used correctly, it is completely unlikely. If water doesn't help, you can use a long, thick wire with gauze wrapped around it. This can be done with your own hands.

Tube prophylaxis should be carried out no more than 1-2 times a year. This will be quite enough. By the way, you need to take care of this at the stage of installing the bathtub. That is, if the decision to buy a hydromassage bath is final, you need not only to allocate a place for it, but also to provide access to the system itself, that is, the same pipes and pump. To do this, you can cover them with a special screen under the bath, which will allow you to hide everything unnecessary, but at the same time provide convenient access to the “heart” of the hydromassage bath.

As for how to clean the pipes in a hot tub, if it is not possible to reach them, you can use a special cleaning agent and again resort to the method of turning on the pump. In this case, the system will clean itself, and a special solution will help remove contaminants by removing it through the nozzles in the tank.

Eventually…

If none of the above remedies work, for example, due to very bad water (which sometimes happens), it is better to consult a specialist and also use water softeners.

design-vannoi.ru

What is strictly prohibited when cleaning a hot tub?

When cleaning a Jacuzzi, the following rules must be observed:

do not use household chemicals that contain ammonia, formaldehyde, ethanol (alcohol), strong alkalis and acids to treat the bathtub and pipes;
Do not clean the bathtub cover with hard metal brushes, abrasives or washing powder;
When using homemade cleaning products, do not add ammonia, formalin or formic acid to them;
Do not clean the system if the nozzles are not submerged under water.

When cleaning your hot tub, do not use hard metal brushes.
Oils, lotions and bubble baths leave a residue in the tubing, so it is not recommended to use them during hydromassage.

Jacuzzi care

A Jacuzzi bath is a very expensive thing that requires a special approach. The hot tub should be cleaned regularly to prevent the jets and pumps, as well as the surface of the tub, from becoming dirty. Since there is a risk of damage if not properly cleaned, maintaining your hot tub should be done without any major mistakes.

Daily care of a jacuzzi bath

After each use, the surface of the Jacuzzi should be rinsed and wiped with a soft cloth. It is worth considering that the rag should be lint-free, and it is not recommended to use hard sponges and detergents. Such actions are sufficient for daily care of the surface of the jacuzzi.

How to Clean a Hot Tub Once a Month

The hot tub should be disinfected and thoroughly cleaned monthly. Fill the bathtub with water, making sure that its level is 5-7 cm above the top nozzles. Dissolve a special disinfectant in water, which can be found in the store. Do not forget to read the instructions and follow the recommendations indicated in them. If this Jacuzzi cleaner is not available, use 70 ml of chlorine in a weak concentration by pouring it into the bath.

Turn the pumps on for a few minutes, then turn them off and wait 15-20 minutes before draining the water. Then you need to fill the jacuzzi with water again, turn on the pumps for a couple of minutes, and after turning them off, drain the water.

Now you need to remove and clean the filters. The instruction manual that came with your hot tub model should include a detailed explanation of this process. Replace the cleaned filters and wipe the surface of the bathtub with a soft cloth.

Annual Jacuzzi Cleaning

When answering the question of how to clean a Jacuzzi, the following point cannot be overlooked: once a year the bathtub should be additionally cleaned using a 7% acetic acid solution. Fill the bath with water so that its level ends 5-7 cm above the upper nozzles, and pour the solution into the water. Using this solution, you can prevent the formation of water stones without damaging the surface of the Jacuzzi. Next, you need to wash the Jacuzzi like this: turn on the pumps for about half a minute, leave the water in the bath for 12 hours, then drain it and fill the bath again. Turn on the pumps for a few minutes, drain the water, rinse the surface of the Jacuzzi and wipe it with a soft cloth.

Source

Do-it-yourself jacuzzi cleaning

You can extend the life of the trouble-free operation of the Jacuzzi if you do not allow contamination of the components (pumps, nozzles, bathtub surface, etc.). In addition, regular cleaning of the Jacuzzi will prevent the occurrence and proliferation of harmful pathogens in the filters and pipes of the system. When caring for this equipment, it is important to follow a number of rules.

Features of cleaning a jacuzzi

Each time after finishing water procedures and hydromassage, it is necessary to rinse the surface of the bathtub with clean water and wipe it with a soft, lint-free cloth. For daily cleaning, it is not recommended to use hard sponges or abrasive detergents.

The Jacuzzi should be disinfected once a month. To do this, you must first fill the tank with water until the water covers the upper nozzles by 50-70 mm. Then a disinfectant solution is added to the water, which can be purchased at the store or made independently. Before using store-bought products, you should carefully read the instructions. If you refuse to buy a ready-made solution, then you need to pour approximately 70 ml of a weak chlorine solution into the water. Then turn on the pumps and wait a few minutes for them to “drive” the solution through the internal pipes. Then the device turns off and after 15-20 minutes (approximately) the water is drained. After this, the Jacuzzi system is flushed with clean water for 5 to 10 minutes.

Dismantling and cleaning of filters is carried out according to the instructions. The filter is placed in a container and washed under running water from a hose. If the equipment is very dirty, then it is soaked in a solution of water with the addition of a special cleaning agent.

How to Clean the Pipes in a Hot Tub

Cleaning the tank

Cleaning tubes and filters

Eventually…

If none of the above remedies work, for example, due to very bad water (which sometimes happens), it is better to consult a specialist and also use water softeners.

design-vannoi.ru

Products for cleaning whirlpool baths

Maintaining your hot tub means regularly cleaning and disinfecting the jets and hoses of the water system. Due to the design features, water often stagnates in the hoses, dirt and deposits are deposited. This leads to the formation of bacteria, algae and fungus and makes bathing unhygienic and hazardous to health. Hard water causes the nozzles to become clogged with mineral deposits and prevent normal water circulation. Over time, this can lead to equipment failure.

Quality products are offered by trusted manufacturers of plumbing fixtures and household chemicals:

①HG

Professional solution for the hygienic treatment of hydromassage baths. Contains natural antiseptics (tea tree essential oil and lactic acid) that kill fungus. When used regularly, it prevents the re-formation of plaque. It is used sparingly, the smell is weak. 540 rub.

② Pufas Glutoclean

Concentrated disinfectant, Jacuzzi cleaner from plaque, rust, bacteria and fungus. According to reviews, it cleans the bathtub, nozzles and water supply system the first time. Disadvantages – fakes come across from time to time (the product is diluted with water). Price – 600 rub.

③ Unicum for Jacuzzis and swimming pools

Eliminates dirt, grease, fungus and algae. Effectively disinfects and cleans hydromassage equipment the first time. Moderately foams. There is a noticeable smell of bleach. Restores the surface of the bathtub and gives it shine. 245 rub.

④DEC

Liquid for disinfecting connections of hydromassage systems, removing lime deposits inside the nozzles and on the surface of the bathtub. With regular use, the antiseptic effect lasts until the next treatment. Disadvantages - wasteful consumption (up to 1/3 of the total volume for complete cleaning). 400 rub.

⑤Dezavid

Hypoallergenic product for complete cleaning of the entire hydromassage system and the surface of the bathtub or shower. Does not contain chlorine, does not require rinsing with clean water. There is no smell. The antibacterial effect lasts up to two weeks after use. Cost – 300 rub.

⑥BAGI Jacuzzi

Concentrate for cleaning nozzles, internal systems and bath surfaces. Eliminates all types of plaque, grease and soap blockages, and unpleasant odors. The effect of use lasts for a month. Disadvantages: it foams a lot, is used up quickly, has a strong chlorine smell. The quality of injector cleaning is average. Price – 300 rub.

⑦Ravak Disinfectant

Professional concentrate for high-quality disinfection of Jacuzzi systems and cleaning the surface of any organic and mineral deposits. Suitable for acrylic products. The product is chemically active and, if inhaled, causes irritation to the eyes and respiratory system. Price – 550 – 600 rub.

⑧ Mellerud

Professional antibacterial cleaner for organic residues, mold and bacteria. Fights green plaque. Disadvantages: often one treatment is not enough; not all contaminants are removed. Perceptible intrusive odor. High price - 1000 rub. for a volume of 1 liter.

⑨ Relisan

Concentrated liquid for professional Jacuzzi care. Cleans the system, returns the nozzles to working condition, and ensures a clean surface without additional washing. The product has a prolonged effect and lasts up to 1 month. 336 rub.

⑩ VEGA

Professional product for hydromassage systems from the manufacturer of bathtubs and showers. For all types of plaque and organic residues. Cleans injectors efficiently. Gives the bath shine. After use, no additional surface cleaning is required. Does not form foam. Price – 600 – 650 rub.

Conclusion: Most effective household chemicals contain active ingredients that can cause irritation to the skin, eyes and respiratory system. This is especially true for disinfectant products. When working with such products, you must not forget about gloves and a respirator.

Eco-products for acrylic bathtubs can also be used for new cast iron and enamel products, for which a gentle cleaning action is sufficient. Old enamel coating becomes porous, so more aggressive and concentrated substances are needed for a good cleaning effect.

Home Remedies for Reservoir and Hydraulics Cleaning

In the absence of professional products, 100-150 ml of “Belizna” can be used as a disinfectant for tubes and surfaces. Active chlorine destroys pathogenic microorganisms, but reduces the elasticity of rubber gaskets and harms the acrylic coating.

Remedies for removing plaque, rust and dark stains from the bathtub can be prepared at home. The most effective are the following recipes:

Mix 2 tbsp. soda ash and baking soda, pour vinegar until pasty, apply to stains, leave for 2-3 hours. After exposure, rub with a soft sponge and rinse with plenty of water.
Dissolve 20 g of citric acid in 250 ml of warm water, apply to the walls of the jacuzzi, leave for 25-30 minutes. After soaking, rub the walls of the bath with a washcloth and rinse off the composition.
Mix 1 part white wine vinegar and warm water and rinse the bath. This composition cleans the walls of acrylic bathtubs well without damaging the plastic structure.
Combine 50 ml of hydrogen peroxide (3%) and 100 ml of ammonia. Apply to dirt, leave for 10-15 minutes, then rub and rinse. This composition is only suitable for enamel baths, but works well on stubborn and old stains. When working with the composition, you should use gloves and a respirator.

When using home remedies, you must remember that you cannot use vinegar with peroxide and “White” at the same time. This combination results in the formation of peracetic acid and chlorine gas, which are toxic to humans. A mixture of concentrated vinegar and hydrogen peroxide is flammable.

Disinfection

The hot tub should be disinfected once a month. It allows you to get rid of pathogenic bacteria in the pipes and on the surface of the bowl.

Disinfection preparations are sold in hardware stores and wherever similar plumbing equipment is sold.

For these purposes, it is recommended to use Metacril IdroNet, “Dezavid for Jacuzzi”, Ravak Desinfectant.

For disinfection, these compositions are diluted with water. Pour the liquid into a special hole located on the side of the bath and turn on the disinfection cycle. After completing the procedure, you need to wait 10 minutes, drain the used liquid and rinse with clean water.

Conclusions and tips for disinfecting a jacuzzi from the specialists “Budsan – your plumber”

Jacuzzis cannot work forever; over time, the pipes begin to leak. They usually break due to improper cleaning with products that corrode the plastic. If you experience any problems with the operation of your hot tub: dirt flies out, a persistent unpleasant odor appears, don’t hesitate to fix the plumbing yourself. The right decision would be to call a qualified specialist to carry out diagnostics in order to determine the exact cause of this situation and perform high-quality repairs.

How to prevent your hot tub from clogging

For preventive purposes, in order to prevent various breakdowns, as well as to prevent the growth of fungus and infection, you need to fill in special cleaning products for the jacuzzi every couple of months. When using the bathtubs, water enters the lower nozzles. In order to prevent this, after taking a shower, you should leave the compressor running for a few seconds. This will prevent mold from appearing.

Therefore, it is completely clear that the compressor must always be working and in good condition. You should not put off repairing it until later, especially if it is already necessary, since after the air compressor breaks down, the entire hot tub fails. Repairing your air compressor can save you significant money in the future. Therefore, you should not put this issue off for a long time, and immediately seek help from professionals to clean your jacuzzi!

Cleaning a jacuzzi and hot tub is fairly quick. It is quite obvious that the condition of the product largely depends on how it is used and whether the rules of use are followed. The more thorough the maintenance, the longer the service life of the jacuzzi will be and the fewer calls to the technicians. One of the most important recommendations is to avoid using abrasives and bleaches. However, if the need to call a specialist arises, then you should contact only experienced craftsmen. These are the ones who work in .

Why do hydromassage clogs occur?

After using the hydromassage mode, when draining, particles of cosmetics remain in the system, the sediment turns into mucus, dries out and a thin crust appears. The next time the hydro mode is turned on, the water softens these particles and they fly out with a terrible smell. If measures are not taken in time, fungus appears, mold forms and you will have to resort to other more expensive methods to remove dirt.

Unpleasant consequences can be avoided by disinfecting the nozzles and hydromassage system. Our company will quickly disinfect any system using special means, which will be used for your use after work. With monthly use, the bath will shine and the incoming water will be clean for a long time.

Regular cleaning instructions:

Cleaning the hydromassage system of an acrylic bathtub, hydromassage shower cabin should be done at least once a month

Fill the bathtub with warm water.

Dilute liquid detergent (according to the method of application, instructions for the detergent) and run the hydromassage unit for approximately 5 minutes.

Turn off the hydromassage system and let the water stand for 10 minutes.

Drain the water.

Refill the bath with water and turn on the hydromassage for 5 minutes.

Drain the water and clean the surface of the acrylic bathtub.

If the bathtub is scratched, you can try cleaning it with felt and sanding the scratches.

Why should you clean your hot tub?

Before starting cleaning, you need to familiarize yourself with the reasons for cleaning. Experts recommend regularly cleaning your Jacuzzi, as mold and bacteria gradually accumulate in the pipes. Such contaminants externally look like sticky black dirt, which can only be removed with detergents. If you do not get rid of such contamination, after turning on the hydromassage, the water will become dirty.

The structure must also be cleaned to remove biofilms. In this case, you will have to use more powerful cleaning agents for acrylic structures.

Jacuzzi and hot tub maintenance

Servicing of the hot tub is necessary for its proper functioning. Jacuzzi maintenance at competitive prices: washing the hydromassage, cleaning nozzles, removing fungus and limescale, disinfection. Prevention and maintenance of hot tubs in Moscow and the Moscow region.

Preventative maintenance of a Jacuzzi with a professional disinfectant for hydromassage equipment prevents the appearance of fungus, bacteria, and mold in the hydromassage system. Maintenance of your hot tub will keep the plumbing looking, clean, and in good working order.

Cleaning and maintenance of hot tubs Jacuzzi - Jacuzzi, Teuco - Teuko, AM.PM - Am Pm, APPOLLO - Apollo, Apollo, Jacob Delafon - Jacob Delafon, Albatros - Albatross, Radomir - Radomir, AQUATEK, Aquanet - Aquanet, BAS - Bass, Triton - Triton, BellRado - Belrado, Grossman - Grossman, Kolpa san, Roca - Rock, Riho - Riho, Doctor Jet - Doctor Jet, DORFF - DORFF, Eago - Eago, Novitek - Novitek, Nordic - Nordic, RAVAK - Ravak, Timo – Timo, Balteco, Villeroy & Boch – Villeroy & Bosch, Victory Spa – Victory Spa, Pool Spa – Pool Spa, PDC Spas, Whirlpool.

To prevent the formation of dirt and deposits and extend the service life of hydromassage plumbing equipment, it is recommended to install water purification filters, both in an apartment and in a private house. If the water is too hard, you should also consider softening it. In order for expensive plumbing equipment to remain in working condition, it is necessary to carry out maintenance and disinfection at certain intervals. Manufacturers recommend turning on the disinfection mode at least once a week. In its absence, care with special cleaning products. Professional servicing is required once a year.

Conclusions and useful video on the topic

Video with rules and recommendations for caring and cleaning the hot tub bowl:

By adhering to the simple rules given in our article, you can not only maintain the presentable appearance of your plumbing fixtures, but also extend the life of the equipment.

Are you looking to clean your hot tub for the first time and don't know where to start? Ask your questions in the comments to this article - we will try to help you.

Or have you been the proud owner of a hot tub for a long time and are doing an excellent job maintaining it? Tell us what products you use to wash the bowl and how you disinfect the equipment - your secrets will be useful to many users.

Final system disinfection

With regular maintenance, the system is disinfected simultaneously with monthly cleaning. In case of severe contamination, longer exposure to antiseptics is required to destroy fungi and bacteria.

Algorithm for disinfecting a hot tub:

wash the surface of the bathtub and the guide elements with liquid soap or a product for the appropriate type of surface;
fill the bath with hot water (+40...+45°C) so that its level is 5-10 cm above the nozzles;
add 200-300 ml of detergent to the container to disinfect the jacuzzi;
turn on the hydromassage at maximum power for 15-20 minutes;
let the solution stand for 25-30 minutes;
drain the liquid, refill the bath with cool water;
turn on the massage for an additional 5-7 minutes;
empty the container, wash its walls with a soft sponge and wipe dry.

Some hot tub models have a self-cleaning mode. If this function is available, the disinfectant liquid is poured into a special hole in the wall of the bathtub.

The following products are suitable for killing fungi and bacteria:

"Wonder Worker Hot Tub";
"Bagi Jacuzzi";
Triton Disinfectant;
Relisan.

Simple rules for proper care

A hot tub is not as demanding and capricious as it might seem at first glance.

She just needs proper and timely care, which consists of following five simple rules:

Before installing the equipment, carefully review the operating characteristics of the equipment. For some models, a cold water pipe must be provided for installation of the solenoid valve. Most models require the installation of a water pre-filter. To ensure easy access for carrying out preventive measures, think in advance about a convenient location for placing plumbing fixtures.
If you want to extend the life of the injectors, use water filters that will trap small particles that contaminate the holes. Only turn on the hydromassage system when the jets are completely covered with water. Otherwise, the unit's motor may burn out.
When receiving a session, do not use oils, lotions or foaming agents. They can clog the hydromassage system, forming sediment in the pipes. When taking water treatments, follow the rule “first enjoy the hydromassage, then enjoy the foamy pleasure.”
When bathing, use only sea salt and those additives that are marked appropriately for use with hydromassage systems.
Avoid contact with any varnish (even hair varnish) on the surface of the bathtub.

If, due to hard water, the hydromassage system quickly becomes dirty, it is worth considering the option of installing devices to soften it.

Cleaning Products Review

Correctly selected specialized household chemicals for cleaning a Jacuzzi will help in the matter of care. Their advantage over conventional bathtub cleaners is that such compositions can be effectively used not only for cleaning the surface, but also for washing and disinfecting the hydraulic system. Here are the most popular and effective ones.

Mellured

This product performs several different tasks: it helps in the fight against unpleasant odors, removes lime deposits, and perfectly cleans and disinfects. Such household chemicals remove all harmful microorganisms from surfaces, eliminate fungus and bacteria. It cleans well not only the bowl, but also the entire pipeline system.

With regular use, the formation of green deposits is prevented.

The manufacturer recommends using it not only for complete cleaning of the system, but also for daily maintenance:

after swimming, do not immediately drain the water;
add 100 ml of cleaning product, stir and let sit for 30 - 40 minutes;
at the same time, turn on the circulation pump several times for 1 minute;
Now you can drain the water and rinse the surface.

With this care option, users forget about mold and mildew.

Unicum

It is a universal product intended for cleaning and preventing contamination of bathtubs with a hydromassage function. It eliminates all harmful bacteria, fungi and mold.

This composition cleans not only external surfaces, but also the internal system. Quickly and effectively fights grease, dust and other types of contaminants. It has disinfecting properties with a long-lasting effect. Suitable for all types of coatings, including acrylic.

Other chemistry

In addition to the most popular formulations presented above, it is worth noting 2 more products.

Triton. Chemicals are used to clean different types of surfaces: acrylic, stainless steel, cast iron. It removes traces of grease, rust, plaque and water scale well. The product is also used to disinfect plumbing fixtures, as it contains disinfectants that prevent the growth of bacteria, fungi and mold.

Edel Weiss. It is used primarily for cleaning the hydraulic system and, judging by consumer reviews, it copes with this with a bang. It is recommended to add the composition to a font filled with water at the rate of 250 ml per 100 liters of water.

Storage tank

Experienced specialists can carry out cleaning in a short time. This will not only return the failed bowl to use, but will also extend its service life.

And all because professional Jacuzzi cleaning products are used.

This hygienic equipment can be washed using traditional methods, but it is highly undesirable.

Acrylic

Like any plumbing fixture, an acrylic bowl requires periodic washing and cleaning.

This is a wear-resistant material with a dirt-repellent effect, but is easily scratched. Therefore, you cannot use powdered cleaning products, only liquid ones.

Hot tub cleaner:

Sano Jet foam has an antibacterial effect. It is used to remove dirt from any acrylic surfaces, including hot tubs. Foam removes limescale and rust without scratching the surface.
Prosept “Bath Acryl” - suitable for all acrylic surfaces. This composition is gel-like, it contains citric acid, due to which effective cleansing is carried out. After use, it forms a thin film that prevents plaque, slows down the appearance of dirt and removes unpleasant odors.
Bagi “Jacuzzi” is also suitable for these purposes. Its unique composition is suitable for cleaning and preventing hydromassage baths. The cleansing is gentle and quickly removes dirt, plaque and soap residue.
Cleaning a Jacuzzi with professional products is carried out according to the same algorithm; only the amount of gel changes (see instructions on the package).

Algorithm of actions:

Fill the Jacuzzi with water until it covers the holes.
Then add cleaner.
Run the bath for a while. For some products, 3 minutes is enough, others require 30 minutes. Read all such information on the label.
The waste water must be drained and the bowl refilled. After two minutes of operation, you can drain the liquid and wipe the tank dry.

Caring for this structure is not difficult if you follow the instructions for using cleaning products.

Cast marble

You can clean any surface of your hot tub at home. The easiest bowl to clean is considered to be a bowl made of cast marble.

This coating is very durable and the surface is easy to clean. Due to the quality of cast marble, there is no need to use professional products.

How to clean a cast marble Jacuzzi:

Grind laundry soap, dilute it with water or use liquid detergent.
Apply the mixture to the surface of the hot tub. Rub slightly with your hands and rinse with clean water.
Once the reservoir is dry, apply a mild car polish. It will add shine to the bowl.

If soap does not help get rid of plaque, use products designed for cleaning acrylic bathtubs.

Steel and cast iron

The steel and cast iron bowls of a regular bathing tank can even be treated with washing powder. However, in the case of a hot tub, this cannot be done.

Large particles clog the internal structure of the hydromassage. For these purposes, it is recommended to use gel or creamy substances that are easily washed off and do not clog the system.

How and how to clean a steel and cast iron Jacuzzi bowl:

Mellerud is made in Germany. Available in 1 liter volume. The substance is sold in concentrated form and is used to clean the bowl itself and the pipeline system. Application: after taking a bath, pour 100 ml of the chemical reagent into the water, stir and leave for 30 minutes. Then connect the circulation mechanism and let the hot tub run for a few minutes. Then the water is drained and the bowl is rinsed with clean water. Mellerud removes bacteria that can lead to infectious formations.
Akrilan is produced in Israel in a volume of 750 ml. It removes plaque, rust and fights mold. The product is sold in a concentrated spray bottle. There is no need to dilute it before use. Apply Akrilan directly from a spray bottle to the dirty surface of the hot tub. Rub with a soft sponge. Wait a little and rinse immediately with water.

Do all work wearing rubber gloves. It is unknown how professional chemicals will affect the skin of your hands.

Hydromassage system care

Installation and maintenance of a bathtub hydromassage system

Maintenance of a bathtub with a hydromassage should be more thorough than in the case of an ordinary bathing tank. This is due to the fact that favorable conditions are created in the internal water circulation system (high humidity and sufficient temperature) for the development and rapid reproduction of various microbes, bacteria and fungi that are dangerous to the human body. The development of colonies of microorganisms can lead to allergies, obstructive bronchitis and asthma, children are especially susceptible to this.

Why does the bathroom smell like sewer? Causes and methods of prevention

The most commonly used chemistry for hot tubs is:

Mellerud (disinfects, removes deposits and odors);
Bugs Jacuzzi (removes mold, bacteria and unpleasant odors);
Akrilan (product from the professional series);
Triton Desinfectant (flushing hydromassage systems);
Relisan (includes liquid for hot tubs, acrylic surfaces and sanitary ware).

Disinfection procedure

Disinfection of acrylic bathtub systems

Disinfection of a hot tub can be done in two ways:

If your bathroom has an automatic cleaning function, the procedure is as follows:
We pour a cleaning agent for hydromassage baths into a special reservoir (the quantity is selected in accordance with the instructions) and turn on the cleaning function;
Drain the water and rinse the bath;
We repeat the procedure with cool water and without the hydromassage bath product;
After completing the cycle, drain the water, rinse the bath and wipe with a dry cloth.
Because it is necessary to care for a hot tub even if there is no such function, we offer a second disinfection method:
Turn on the hydromassage at the highest power for 10 – 15 minutes;
After turning off the hydromassage, leave the water for half an hour so that the cleaning agent is fully effective;
Drain the water, pour in clean water and turn on the hydromassage for 5-7 minutes, flushing the system from residual disinfectant;
Next, drain the water and wipe the bowl dry.

Before cleaning the bathtub with a disinfectant, it is necessary to wash the bowl from dirt and grease deposits with ordinary soap.

Subtleties of cleaning system elements

The main difference between caring for a hot tub compared to traditional models is the need to clean the surface of not only the tank itself, but also the internal filling of the structure. These are jets and nozzles, supply pipes and a pump.

Maintenance of hydromassage equipment includes cleaning the surface every few days in combination with preventive measures, as well as washing nozzles and pipes.

Surface treatment methods

Before treating equipment with disinfectants, it is necessary to wash the bowl from grease and dirt with ordinary detergents.

If you notice that hard water leaves limescale deposits, rinse the whirlpool system with clean water and wipe with a cloth each time after bathing.

The hydromassage system is cleaned in the following sequence.

Apply detergent to the surface in accordance with the instructions described on the label.
Wait the period specified by the manufacturer. On average it takes 5-10 minutes.
Rinse off the product with streams of clean water.
Wipe the surface dry with a napkin. For this purpose, it is best to use cotton or bamboo napkins, or microfiber rags. They perfectly absorb moisture without leaving streaks on the surface.

If a self-cleaning system is installed in the hot tub, the disinfection procedure takes place with minimal human intervention.

Before starting the automatic mode for disinfection, you only need to place a portion of the disinfectant in a special compartment

When dealing with traditional models that lack a self-cleaning system, preventive disinfection is carried out in several stages:

Fill the tank with water, the temperature of which reaches 20-25 °C.
Dissolve the prepared product in water.
Start the hydraulic and aerosystem for 5-7 minutes, setting the highest power. In some models, on the contrary, manufacturers recommend shutting off the air supply so that only water without air masses moves through the pipes.
After turning off the equipment, leave the filled bath for another 5-10 minutes so that the product dissolved in the water completes its task.
Open the drain hole and drain the water. You should be prepared for the fact that dirt flakes accumulated in the pipes will begin to flow into the bowl along with the water.
Refill the bath at a level above the nozzles, but with cold water. The hydraulic and aerosystems are started, after which the tank is emptied again.

After such a “bath” of the tank, the bathtub will sparkle and shine like new.

The liquid level in the reservoir must be 8-10 cm above the location of the nozzles, otherwise when the hydromassage is turned on, the engine will quickly fail

The taps and spout will have to be additionally treated with liquid detergents, then rinsed generously with water and wiped dry with a napkin.

If at the time of general cleaning of the plumbing you do not have a special product at your disposal, you can use a 7% bleach solution or “Belizna”. To treat a medium-sized bath, you will need 1.5 liters of this chlorine solution or 100 ml of “Whiteness”.

A solution of citric acid helps to quickly remove mineral deposits from waterscale without damaging the surface of the plumbing fixtures.

But “aggressive chemicals” should be used only as a last resort, since they can harm the internal gaskets of the equipment. To protect yourself during the procedure, the room should be well ventilated.

Prevention of lime deposits

Once a year, additional cleaning of the system should be carried out to prevent lime deposits.

If the maintenance of the hot tub has been irregular and water stone has accumulated inside the equipment, the following measures will help correct the situation:

Fill the bath with water so that it covers the nozzle holes.
Take the finished product or prepare a 7% solution of citric acid. To treat the entire surface you will need up to one and a half liters of the prepared solution.
The solution is mixed with water in the bath and the system is started. During initial cleaning, the system should operate for at least half an hour. In the future, when performing routine cleaning, the duration of the system operation may not exceed 10-15 minutes.
The reservoir is left filled for 12 hours and then emptied.
The bath is refilled with clean water, the system is run for 5 minutes, after which the reservoir is emptied.

If after cleaning the tank it is noticed that dirt is coming out of the nozzles, they should be disassembled and cleaned individually. To do this, you need to remove the decorative ring and unscrew the metal cap of each nozzle. The holes are cleaned manually using a cloth soaked in water.

Cleaning pipes is a more difficult task. After all, the hydromassage system is an intricacy of corrugated polymer tubes of different diameters. Tubes should be removed in strict accordance with the instructions supplied with the equipment.

It is better to entrust the dismantling of pipes to professionals, since incorrect disassembly of the structure and subsequent assembly of elements can lead to more complex and expensive breakdowns

Dismantled pipes are cleaned under high pressure of water without the use of special detergents. If rinsing with water does not help, use a long, dense wire with a piece of gauze wound around the end.

If the hydromassage mechanism malfunctions, replacement of nozzles, water collectors, or a hydraulic or aero compressor will most likely be required. In order not to aggravate the situation, it is better to entrust this work to professionals.

Is your bathtub fixture in need of expensive repairs that cost the same as buying a new bathtub? In such a situation, we recommend that you familiarize yourself with the recommendations for choosing a hot tub.