My computer chair is creaking, what should I do?

Creaking sounds of wooden structures

If an old wooden sofa creaks, there may be several reasons.
Each individual case has its own reason for the “musicality” of the object.

When upholstered furniture (sofa), wooden or metal, creaks, you need to arm yourself with tools.

The most likely of them:

drying out of any part and the appearance of cracks;
the spring block is deformed or one of the springs is bent (broken).

When you decide to figure out why your sofa is squeaking, you need to gain some knowledge about the structure you're dealing with.

Wood loses its elasticity over time. Its structure is changing. While some tree species are resistant to moisture (for example, aspen), others can be quite fragile and quickly fail. Much depends on the correct use and care of the product. Both one panel and all wooden parts can dry out if normal humidity conditions were not observed during operation or the furniture was placed in direct sunlight.

Sometimes creaking is characteristic of a new product when the connections are poorly fitted, sometimes this appears after prolonged use.

The sofa needs to be disassembled before work.

The cause may also be loose (or too tight fasteners). The sofa makes a characteristic grinding sound. It is also possible for the padded batting or other soft upholstery material to become thin and deformed in other ways.

The reason could be a spring block rusted from moisture, wood that has dried out over time, and much more.

It is necessary to examine the internal state of the furniture and determine the location of the creaking noise.

If old wooden furniture creaks, you will need to replace the spring unit or its parts. The first is preferable, since we are talking about wear of the material as a whole, and then another spring or section may break. Connecting individual links is quite labor-intensive work.

Wood loses its elasticity over time.

One reason may be wear and tear of the soft cushioning material. Over time, due to humidity, they could rot and turn into dust, creating access for the connecting elements to each other, which is why the creaking occurred.

Much depends on the correct use and care of the product.

To correct the deficiency, prepare the tools.

A product that is too old is a little more difficult to tidy up. To determine the exact cause, the sofa should be carefully disassembled. It is likely that replacing elements or lubricant will be sufficient. Otherwise, you may need to buy new furniture.

The cause may also be loose (or too tight fasteners).

Which beds squeak?

The most common among them are: Fasteners, connecting elements - over time they can become loose and break; Slatted bed base - the structure creaks due to the contact of wooden parts or breakage of fasteners; Mattress – it is not the mattress itself that makes the sound, but its springs.

Interesting materials:

How to open the console in The Binding of Isaac Repentance? How to open the gas tank flap from the outside? How to open a car using a cord? How to open a disposable mill? How to open the Macro window in Excel? How to open a window from the street? How to open wasp in windowed mode? How to open an Outlook email in a browser? How to open a plastic window with ventilation? How to open a port using Hamachi?

How to lubricate a chair

Most often it is recommended to lubricate squeaking parts with WD-40. It contains solvent and mineral oil, which facilitates sliding and protects the surface from moisture. “Vedashka” is convenient to use at home, as it is produced in the form of an aerosol and comes with a narrow long spout - for carefully applying it to hard-to-reach places.
You can use solid oil or Vaseline.
Any lubricant for equipment is suitable, for example, which was previously used for door hinges or a sewing machine.
Do not take vegetable oil or cosmetics - even if there is an effect, it will not last long.

Chair care

Which office chair is better?
To make a refurbished chair serve you longer, follow a few simple rules.

Do not swing in a chair with the swing mechanism fixed - you will destroy the gas lift, and it will not last long under such a load.
Do not sit down on the chair abruptly, in a big way, so as not to overload it.
To clean the chair, use mild detergents to avoid damaging the parts with aggressive chemicals and accelerating their wear.
Regularly check the reliability of the screws and add lubricants if possible, so as not to end up completely disassembling and repairing the chair.

Conclusion

Comfortable furniture for work and relaxation is not only momentary comfort, but also a matter of your health. Many problems with the spine and joints are caused by incorrect body position during the day. Be careful when choosing and caring for your work chair to avoid big problems in the future.

How to fix the problem

To repair a computer chair you will need the following tools:

a set of screwdrivers (straight and Phillips);
hex wrench;
hammer;
furniture lubricant;
pliers;
spare bolts and nuts.

Due to squeaking, it is rare to replace parts. More often than not, to fix the problem, it is enough to tighten the bolts and lubricate the mechanism. To do this, you can use both specialized products and improvised ones - mineral oil or Vaseline.

Lubricating office chair parts

To lubricate the parts of a computer chair, you need to:

Prepare petroleum jelly, grease or WD-40, which contains mineral oil and a solvent to enhance gliding.
Turn the chair over.
Find the latch in the center of the cross.
Remove the washer.
Remove the gas lift.
Lubricate the washer, bearings, gaskets.
Reassemble in reverse order.
Turn the chair over.

Instructions on how to attach the front to the dishwasher with your own hands

Replacing fasteners

As a result of prolonged use of an office chair, the fasteners may become loose and begin to creak. To fix the problem, turn the computer chair over and tighten the bolts until they stop using a screwdriver or hexagon. Most often, 2-3 bolts are on the armrests, 4 on the rocking mechanism, and the same number on the seat. There may be more or less. It all depends on the type and design of the office chair.

If, when tightening the fasteners, it turns out that some bolts are turning, they are removed, a special sealant is poured into the hole and quickly screwed back in. Instead of sealant, you can use PVA. In this case, the waiting time must be increased until the glue is completely dry.

Replacing gas lift

If a gas lift breaks down, lubricating it will not improve its performance. If it not only makes a squeaking sound, but also fails, it should be replaced. After such manipulations, the office chair will last a long time and the cost of repair will be cheaper than buying a new one.

Before you buy a new gas lift, you need to make sure that it fits the model of your computer chair. When replacing it, a number of actions are performed sequentially:

The screws are removed from the seat.
They press the crosspiece with their feet, and take the seat by the armrests and, rocking, pull it up.
To remove the gas lift, use a rubber hammer and a ring drift.
Installing a new gas lift.

It should be remembered that blows with a hammer when removing the gas lift should not be strong, so as not to damage the cross.

Wheels

To repair wheels you will need the following tools:

screwdriver - for removing screws;
lubricant - for processing rollers;
hammer - for removing parts from fasteners.

If the cause of the computer chair squeaking in the wheels is dirt accumulated there, you should disassemble them, clean them, lubricate them and reassemble them. To do this you need:

Turn the chair over and try to clean the wheels using a screwdriver, scissors and other available tools.
If it is not possible to remove dirt, the wheels are removed from the crosspiece by unscrewing the bolts.
The wheels are washed with water, cleaned, and inspected for damage and wear.
If further use is impossible (damage, cracks), there is nothing left to do but replace the parts.

Is it possible to lengthen the drain hose of a washing machine and how to do it

When replacing wheels, experts advise buying a complete set and replacing all 4 so that wear is even during further use.

Barsky's recommendations

Office chair. what to look for when choosing?

Manufacturer of office and home furniture Barsky invites its customers not to buy a chair “blindly”, but to test it. To do this, you need to call the contact phone number or request a call back. How is this convenient? First of all, we, as a domestic manufacturer, clearly understand that comfort during work comes first. Therefore, before buying, you need to sit in a chair, inspect it, test all the features and compare with other options. Reading about the advantages of a particular mechanism is one thing, but seeing everything for yourself and touching it is a completely different matter.

Our customers are provided with a unique opportunity to test products free of charge. In a conveniently located location - right in the city center, on Shevchenko-14, there is our exhibition hall, the Barsky show room, where you can see chairs, tables and other furniture sets from the Ukrainian manufacturer. Waiting for you!

The computer chair is creaking - what to do? How to rid yourself of discomfort

Step-by-step instructions on how to assemble an office chair and operating instructions

Reasons: why a computer chair starts to creak

The screws between the parts were loose, or they were not tightened properly at the production stage.
The grease that was on the bearings and joints has dried out.
Due to poor quality parts or improper use, the mount broke. In this case, you cannot do without purchasing additional parts or the help of specialists.
Also, the reason may be ordinary dust, which has accumulated in the cracks and prevents the mechanisms from working as expected. In this case, careful disassembly and cleaning of the chair will help.

In what places does it squeak?

If your office chair squeaks when you move, inspect the wheels. Often small debris or dust stuck in the cracks causes an unpleasant sound. Dirt can be removed with a narrow, long object or blown out using a can of compressed air. If a squeaking sound is heard when the chair rotates, the problem may be with the gas lift. This is the part responsible for adjusting the chair in height, torsion around its axis and the spring function (reducing the load when you sit in the chair). To inspect the gas lift, turn the chair over and look for the latch in the middle of the cross.

Remove the washer by picking up the tongue, carefully remove the gas lift and lubricate the bearings, gaskets and other parts. If you still hear squeaking or clicking noises, the problem may be more serious and will require replacement. A new gas lift will still cost less than buying a whole chair.

A new gas lift will still cost less than buying a whole chair.

Many chairs have a “sore spot” - the rocking mechanism. The chair is controlled using a piastra, spring-screw or centered mechanism (you will recognize it by the protruding handle). Often the problem is a broken piastra weld. Inspect the fasteners and, if necessary, tighten the bolts with a screwdriver. It happens that after tightening, the screws quickly become loose again - here ordinary PVA glue or any other will come to your aid - pour a few drops into the gap and tighten it tightly. Do not turn the structure over until the glue has completely dried.

When a squeak is heard from the L-shaped mechanism when changing the position of the backrest, you need to remove the side corners by picking them up with a flat screwdriver - they are connected to each other with plastic latches, so act carefully so as not to damage them. Wipe the insides with a rag, add lubricant to the spring and return the plugs to their place.
If the armrests are loose, tighten the screws.
Disassemble the backrest if it is the cause of the squeaking.

Instructions on how to disassemble the back of a chair

You have already disconnected the backrest from the chair and from the L-shaped part.

Inside, a metal insert is usually attached to a plywood frame. It is necessary to check the reliability of the fastening, tighten the screws if necessary and lubricate all suspicious places.

How to lubricate a chair

Most often it is recommended to lubricate squeaking parts with WD-40. It contains solvent and mineral oil, which facilitates sliding and protects the surface from moisture. “Vedashka” is convenient to use at home, as it is produced in the form of an aerosol and comes with a narrow long spout - for carefully applying it to hard-to-reach places.
You can use solid oil or Vaseline.
Any lubricant for equipment is suitable, for example, which was previously used for door hinges or a sewing machine.
Do not take vegetable oil or cosmetics - even if there is an effect, it will not last long.

Chair care

To make your refurbished chair last longer, follow a few simple rules.

Do not swing in a chair with the swing mechanism fixed - you will destroy the gas lift, and it will not last long under such a load.
Do not sit down on the chair abruptly, in a big way, so as not to overload it.
To clean the chair, use mild detergents to avoid damaging the parts with aggressive chemicals and accelerating their wear.
Regularly check the reliability of the screws and add lubricants if possible, so as not to end up completely disassembling and repairing the chair.

Conclusion

Instructions on how to disassemble the back of a chair

You have already disconnected the backrest from the chair and from the L-shaped part.

The screws you are interested in are located at the bottom of the backrest; to get to them, pull up the plastic casing or pick it up with a thin, flat object.

Inside, a metal insert is usually attached to a plywood frame. It is necessary to check the reliability of the fastening, tighten the screws if necessary and lubricate all suspicious places.

IMPORTANT! At any stage of disassembly, it is important not to overdo it. If something doesn't work, double-check the part for latches and screws. Otherwise, you will waste time or break off something that needed to be unscrewed.

Necessary tools for repair

To repair a computer chair and eliminate unwanted sounds, you will need the following tools:

screwdrivers - Phillips and straight;
hexagon;
pliers;
hammer;
special furniture lubricant;
spare accessories.

Most often, there is no need to change any parts of the chair; they break very rarely. The entire repair will consist of lubricating the mechanism or tightening the bolts. For lubrication, it is best to use WD-40 spray. If you don’t have it at hand, or the product doesn’t help, you can use any oil lubricant or even regular Vaseline.

Avoid direct sunlight

Exposure to direct sunlight will dry out and discolor your cane furniture over time—and drying out is what will lead to tears and breakage in the structure. Instead, you want to keep it hydrated.

Our customer Christina also has a rattan bug

One method is to keep your figures in a room where you have a humidifier, or, if you live in a humid climate, on a covered porch. Katherine leveled the ideal conditions with a cigar humidor.

It is better to bend the latches from the entrance side of the guides, but there is no need to bend them too much, since they are soft and are reluctant to return to their original position.

Now we disassemble the mechanism and pay attention to the serviceability of its elements. In my case, the spring responsible for the smooth tilt of the back was broken, but everything else was intact

It is difficult to find such a serviceable spring, so we do without it, but we also do not throw away a broken one, since it is needed for the operation of the mechanism.

Design features

Before you begin repairing a computer chair, experts recommend carefully studying the types and design features of such products. In specialized stores you can see the following models of computer chairs, which have individual design features:

for the manager - a five-beam hollow cylindrical base, a multi-block for adjusting back resistance, seat depth and roll level;
for employees – light weight, multi-block adjustment of seat height, armrests and backrest angle;
for guests - four legs, a comfortable seat and backrest.

Despite the variety of models, all computer chairs have a similar design, which consists of a number of components.

A five-point cross is a plastic or metal part that serves as a support for the entire structure.

Rollers are iron or polymer parts that are installed along the edges of the base. The maximum number of rollers is 5. A distinctive feature is the presence of metal fasteners and a hinge.

How to reupholster chairs with your own hands: simple tips

To remove the gas lift, you need to remove the protective casing on the leg, having previously dismantled all elements that impede access;
There is usually a spring latch at the bottom center of the cross. It should be removed from its seat;
Remove the bearing and other components under the retainer. Remember exactly the sequence of their location;
Now the cross itself is removed. Thus, you open access to the gas elevator;
Get rid of the cover. The junction between the elevator and the seat is the most difficult area. When the chair is actively used, it can be difficult to simply pull out the gas lift. Treat this area with a penetrating lubricant. WD40 works great;
Remove the old gas lift itself, install a new one, and reassemble the entire assembly, proceeding in reverse order.

This is how you can repair your favorite computer chair at home without outside help.

Armchairs include a number of elements that usually cannot be repaired or restored. The whole point of the repair comes down to removing damaged parts and installing new parts in their place.

I think you will succeed and you will definitely succeed.

A modern office chair is a functional and comfortable piece of furniture, equipped with a rather complex mechanism that sooner or later fails. In such a situation, there are three options for the development of events: purchase a new one, take it to a specialized workshop, or repair the office chair yourself.

As practice has shown, it is quite possible to carry out such work on your own. The only thing that is required from the master is strict adherence to the sequence of actions and implementation of the instructions that will be given in this publication.

Causes of sound

Most often, a new or already used computer chair begins to creak from the frame itself. The cause of these unpleasant sounds may be the following:

incorrect assembly;
failure of one of the parts;
not fully tightened bolts.

The office chair mechanisms that regulate the rocking process during use can also become weakened or damaged. They, no less than the frame, can make unpleasant sounds that irritate the average working person. The back of the chair itself at the place of its attachment rarely makes extraneous sounds, but still, if the reason is not found, then you should check the internal bolts. Repairing the backrest is carried out at home and with your own hands; you need to either replace or tighten the bolts.

If unpleasant sounds come from somewhere below, then the gas lift is certainly malfunctioning. It works according to a shock absorber circuit and may fail during service. It can be done, but it will be a little more difficult than disassembling the back.

The office chair is creaking - what to do?

Is your office chair squeaking? You need a good Phillips screwdriver and WD-40.

Creaking can occur for several reasons. The joints between the plywood frame and metal parts may creak if the screw connections or the metal parts attaching to the plywood become loose.

Solution:

You need to disassemble the chair, remove the plastic covers, lubricate the metal-plywood contact area, tighten the screws well, and assemble the chair.

2. The “Permanent Contact” mechanism connecting the seat and backrest creaks. Solution: lubricate the mechanism.

3. Creaks at the junction of the crosspiece and the gas lift. Solution: lubricate the bearing in the crosspiece. A very rare cause of squeaking.

4. “Drummer” - if all else fails.)))

In detail using the example of the Prestige chair.

Most likely the back is creaking.
We are repairing it. To do this, unscrew the figured screw A (see diagram), pull the back up and pull it out of the Permanent.
In the lower part of the backrest we find two screws that secure the plastic cover to the plywood frame, unscrew them. Pull the plastic trim (carefully) along the plywood frame. The direction is upward, if you imagine that the back is in its usual place. The fasteners should come out of the grooves in the plywood frame. If they come out, the pad will hang loosely. Remove the cover. The metal insert is attached to the plywood frame with four screws. Most likely they are not tightly screwed. It happens that one or two screws are lost (if more, then the back will no longer hold on). You can get these screws in our store (a couple of pieces per hand for free). Tighten the screws well and attach the plastic cover to the frame. You can, just in case, lubricate the place where the insert is mounted with plastic gaskets and a metal plate.
We are repairing the seat.
Turn the chair without a back upside down. We remove the Permanent by unscrewing the figured screw B. The “Piastra” mechanism is attached to the seat with four screws. We unscrew the screws, lubricate the metal-plywood contact area, and tighten the screws tightly.
If the seat stops squeaking, good. If it creaks or if the armrests are loose, unscrew the screws, remove the piastrum with gas lift and crosspiece to the side, and remove the plastic cover.
The armrests are attached to the seat with three screws each. We twist them tightly. Reassemble in reverse order.
Unscrew the curly screws A and B. Remove the Permanent. Unclip the plastic case. Lubricate all metal parts in contact with each other or spray with WD-40. Assemble the cover, assemble the chair.
If the chair creaks when rotating without load and the creaking comes from below, then the gas lift bearing needs to be lubricated. Turn the chair over. There is a lock in the middle of the cross. Let's take him out. Carefully, so as not to lose small parts, remove the washer and pull out the gas lift. Lubricate the bearing and reassemble in reverse order.
If lubrication of rubbing parts and surfaces does not help, then the last option remains - the gas lift creaks.
In this case, the creaking will be like clicks, i.e. at the very beginning of swinging in any direction. This means that the hole in the gas lift “sleeve” is much larger than the gas lift rod and the rod swings freely in the hole (it will be clear if you turn the chair over and determine the play by rocking the cross.) This problem is “treated” by replacing the gas lift sleeve, or the gas lift assembly.

How to remove the gas lift of an office chair

You should not use a gas wrench to remove the gas lift - you will damage the surface and it is not a fact that you will be able to remove it this way.

To change or try to repair the gas lift of the chair, you must first remove it. To do this you will need a wooden or rubber mallet. Having turned the chair over the table surface, take it by the gas lift cartridge itself and use a mallet to tap on the piaster (the metal platform to which the seat is screwed), but without fanaticism - so as not to damage it.

But, if not, go to any auto repair shop and ask them to weld the broken seam.

male version of squeak elimination

https://youtube.com/watch?v=see2b4eZr2w%3F

I hope that you liked the article, if you want to correct the author or share your thoughts, leave a comment below. I recommend joining one of our groups on social networks:

and then you will be aware of new articles and I will be glad to see your ideas.

_ _ _Read in full » https://100uslug.com/skripit-ofisnoe-kreslo-chto-delat/

How to get rid of a squeak

If unpleasant sounds appear while using the chair, you need to find their source. After determining the epicenter of the sound, you need to do the following:

If the source of the creaking is the backrest or seat, you need to separate this part from the others. If the reason is in the seat, first remove the backrest. The mechanism that connects these parts of the chair is called permanent contact. Mounted into it, the securing screws are easy to remove even without the use of tools. Now we turn the chair over and unscrew the screws that connect the metal insert and the plywood. After this, a plastic cover will remain. Let's remove it. Now you can see the plywood in its entirety. At its edges there are fastenings for handles. Most often, 6 screws are used as fastenings. They need to be unscrewed. Now we assemble the structure in reverse order

Particular attention should be paid to screwing the fasteners.

If the squeak is directly related to the permanent contact, you need to buy a metal lubricant. It is necessary to unscrew the screw fastenings and apply a coat of paint to the mechanism

The ideal option would be WD-40 or any similar lubricant. If the source of the squeak is located at the junction of the gas lift and the crosspiece, the same lubricant will help us.

Prevention

Each instruction manual included with the computer chair contains information that the product requires maintenance once every six months. Such measures involve cleaning all parts and elements from dust, replacing worn mechanisms, as well as lubricating fastening units. Regular implementation of such measures is the key to the longevity of the product.

In addition, you need to know and follow the rules for using a computer chair. To avoid damage, you need to handle it with care:

do not sway from side to side with pressure on the back;
do not spin around in your chair as if it were a carousel;
do not get into it from a running start.

Standard furniture has its own load limits. If the person who plans to use it has a significant body weight that exceeds the average, he needs to choose special reinforced chair models.

How to quickly fix a squeaking office chair, see below.

Operating rules

To prevent complex breakdowns and extend the life of your computer chair, experts recommend immediately after purchase that you carefully study the manufacturer’s instructions, which detail all operational nuances.

Along with the classic rules for using the product, professional craftsmen recommend paying attention to the following tips:

operate the product only in a dry and well-ventilated area; a chair that has been exposed to low temperatures is strictly prohibited from immediately being assembled and used; the optimal time for adaptation is 24 hours; during assembly, maximum care must be taken, trying not to break the threads by excessively twisting the elements; It is strictly unacceptable to exceed the load on the crosspiece.

Experts point out that one chair is intended for only one person, and using the product by a large number of people can have disastrous consequences.

You need to sit down on a chair smoothly and carefully, trying to avoid sudden and forceful movements. The armrests also need the same treatment; you shouldn’t put pressure on them, much less sit down on them.

The armrests also need the same treatment; you should not put pressure on them, much less sit down on them.

People who are overweight need to purchase only structures with metal elements that are more durable. You should also not use the chair to move heavy loads and objects.

When the wheels get between the joints of the tiles, they become deformed, and after a while they break completely.

The upholstery of the product, which needs to be treated with care and regular cleaning, is no less vulnerable. To remove stubborn stains, it is permissible to use only special cleaning products specified in the instructions. To extend the life of a computer chair, experts strictly prohibit giving it to small children for entertainment. Improper use of the product can lead to irreparable damage.

We should not forget about regular preventive inspection, which includes lubricating all moving elements, as well as tightening loose nuts and screws.

The product should be inspected at least once every 3 months, but it is better to pay attention to the chair every 30 days. If the above recommendations are not followed, the purchased chair may quickly fail, and the purchase of a new product will entail additional financial costs.

A computer chair is an important element of every office worker’s workplace. Given the increased demand for this type of furniture, manufacturers produce a wide range of such products. Despite the external differences, the design and principle of operation of the different types are almost the same, so you can fix the breakdown and restore the working condition of the product yourself at home, following the recommendations of experienced craftsmen, which will significantly reduce the financial costs of repairing or purchasing a new chair.

How to repair computer chairs, see below.

Possible problems and errors

Problems with wheels on office chairs occur when they are used on hard surfaces. On parquet and laminate flooring, plastic rollers wear out quickly. They are more suitable for short-pile carpets. For hard floors, you should choose computer chairs with rubberized wheels. When choosing, you should pay attention to the elasticity of the seat material. It's worth trying to sit in it. If there is a dent left after standing up from it, it is not suitable for long-term use.

Gas elevator failures are most often associated with the fact that the maximum permissible load is exceeded by users. You should pay attention to this characteristic when purchasing a chair. Breakdowns and creaking of the gas lift may be associated with exceeding its service life. Most often, with careful use, a computer chair lasts no more than 10 years, after which the gas lift is replaced and you can continue to work in it.

Replacing gas lift

If the gas lift in the chair does break, it is impossible to repair it. Only replacement will save. If the gas lift has failed and is practically touching the floor, then there is no choice: you will have to disassemble the chair and install a new mechanism. But after these not very complicated manipulations, the chair will last longer, and it will obviously cost less than purchasing a new one. Be sure to make sure before purchasing that the new part will fit the chair model.

Replacement procedure:

First, unscrew the seat screws and remove it from the mounting.
Use a ring drift to remove the gas lift. It will be easier if you lean the cross on the table, for example.
You can use a hammer, but be careful not to damage the chair.
Securely fasten the crosspiece and install a new gas lift.

Some more tips for use and care:

If the chair is fixed with a rocking mechanism, do not swing in it under any circumstances. In this way, you can quickly lose the gas lift or even the entire chair: the mechanism is severely damaged and ceases to function as it should.
If you still have a valid warranty, take advantage of it and do not attempt to repair the chair yourself (lubrication is not included in the repair).
Before lubricating the gas lift, make sure it is in good working order, otherwise it may suddenly jump up and injure you.
If the material itself creaks, alas, only buying a new chair will save you. However, it is naive to believe that an executive chair made of cheap plastic will last a long time without creaking.
For long-term sedentary work, it is better to choose a chair made in Germany or Italy, as well as Polish and Russian. Asian models are still lame in terms of quality, and are more likely to end up wasting money.

A long time ago I bought myself an office chair. It was standing there, working, but recently it started to piss me off terribly. The slightest movement on the chair and immediately the most terrible creak. We need to fix this. There are two options:

Throw out the chair and buy a new one (never a budget option)
You can eliminate creaking yourself (cheap and fast)

With the first option everything is clear. Let's consider the second option.

We will need a screwdriver, WD-40 lubricating garbage (you can buy it at any hardware or auto store, it costs about 100 rubles), and the main character itself - a chair.

The actors are assembled. Let's get started.

Let's disassemble the chair. We remove the seat. Mine was unscrewed with 4 bolts:

Ready. We have complete freedom.

In general, it is not necessary to disassemble, but for the thrill of sensations, we are not looking for easy ways.

We lubricate everything we can: - The little thing that adjusts the height of the chair

— The place where the chair seat is attached

I went a little overboard with the WD. Therefore, we smear the excess with a napkin so that it does not drip.

Be sure to lubricate all places where plastic comes into contact with either plastic or metal. In general, we lubricate everything that comes to mind, so that nothing creaks.

All is ready. Everything was lubricated.

We collect the chair and enjoy the quiet, reborn chair

About six months after purchase, the bar stools began to creak. My husband tried to lubricate it, but it didn’t work, they still creaked.

Nobody canceled the Geverleistung for 6 months.

Or maybe they have a warranty, then it’s at least a year.

Are the chairs wood or metal?

Chairs are not door hinges, why lubricate them?

Let him pick up a screwdriver and tighten the screws, tie bolts or whatever.

The bar stool can be easily disassembled from top to bottom. Find out first where the creaks are.

There are probably different chairs, and we don’t know which one Topikstarter has.

For example, take this bar stool apart

At t.s. most likely collapsible.

After half a year of use, the ties have loosened and now the parts do not fit tightly together, which is why they creak.

For example, take this bar stool apart

Need to read more carefully

Thank you all very much for your answers.

Yes, we have collapsible chairs with metal legs.

My husband will try to tighten the fastenings this weekend. Let's see what happens)

What's wrong with the chairs, does your husband keep pouring oil on them?

We also have one creaking at first, now there are already two, creaking at the base where the circle itself is the leg, spraying WD helps for a while then again, but who said take it apart, and you won’t be able to take it apart, there’s a spring there and once you put it on you won’t be able to pull it out anymore.

All of these bar stools have the same design. You unscrew the seat and everything comes apart. The base is another matter; the attachment of the leg to the circle is different for different chairs. I had to replace the bottom of an expensive chair with the bottom of an old cheap chair because the leg was not securely attached to the base circle. It turned out - the upper part is matte, the lower part is chrome-plated.

Source

How to go through the floor

If you cannot eliminate the squeak using simple methods, it becomes necessary to dismantle the coating.

Dismantling

First you need to remove the baseboards. When needed for reuse, they are removed very carefully.

To determine the location of the nails, carefully pry the baseboard with a pry bar. Then it is recommended to use it to remove the boards. When removing bars, they should be numbered immediately

This will help you lay the boards in the required sequence. Cracked and rotten boards are numbered and set aside

When removing bars, they should be numbered immediately. This will help you lay the boards in the required sequence. Cracked and rotten boards are numbered and set aside.

Cleaning the base

After removing the boards, it is recommended to carefully remove the base. Otherwise, it will not be possible to determine the causes of the creaking. If there are cracks in the concrete base, they need to be widened, cleaned and primed. Damage can be repaired with cement mortar. It is also permissible to use a special putty.

Setting lags by level

It is recommended to set the logs level. They must be located in the same plane. For leveling, a long level measuring 1.5-2 meters is required. If it is necessary to raise the logs, it is permissible to use spacers or special anchors. After aligning the logs in one plane, they are firmly attached to the base.

Insulation and sound insulation

To do this, the floor is covered with waterproofing material. Insulation is placed on top. Its role is played by polystyrene foam or expanded clay. It is also permissible to use mineral wool.

The insulating layer is covered with a membrane, which helps remove moisture and prevents dust or mineral wool lint from entering the home. All coverings are attached to the joists with a stapler and staples.