Anyone who chooses laminate flooring should be prepared for the fact that sooner or later scratches will appear on it that will have to be masked. For this purpose, a special putty is produced for the laminate, with the help of which its cosmetic repairs are carried out.
Putty for laminate
Whatever one may say, such a floor covering cannot be called absolutely reliable, since it is not completely resistant to mechanical influences, especially abrasive and scratching ones. Even minor damage can be clearly visible. Moreover, a violation of the integrity of the coating in one place can often lead to further serious damage to the material over time. Therefore, if scratches or chips appear, they must be repaired immediately. In addition, in order to preserve the original condition of the laminated coating, it is advisable to treat it with a special agent immediately after installation.
Possible causes of laminate damage
Laminate is a very aesthetically pleasing, but rather “capricious” floor covering that requires careful use. The fact is that its protective top layer, although designed for a certain mechanical load, is very unstable to some external influences. When purchasing this material, you need to know what effects are detrimental to it.
- Most often, damage to laminate flooring occurs if it is laid in rooms with high levels of human traffic. At home, this is the hallway and corridor, since this is where dirt and sand are carried in from the street on shoes. And this not only stains the coating - small hard particles of dirt act as a very aggressive abrasive, abrading and scratching the surface of the laminate floor.
- Overmoistening of the coating plays a destructive role. Water seeping into the seams between the boards leads to damage to their structure - they can begin to delaminate or swell. Moisture also has a negative effect on the design of locking joints. The entire coating may become noticeably deformed at the seams or even go into waves.
- Rearranging pieces of furniture is one of the most common causes of deep scratches on laminate flooring. Such defects can expand over time, which can lead to deep damage to the board and the need to replace it.
The wheels of an office chair, especially if they are faulty, can leave scratches and abrasions on the surface of the laminate.
- The wheels of an office chair are also the “sworn enemy” of this coating, as they can completely erase the protective layer of the laminate over a fairly large area.
- Heels, especially those with metal heels, can also cause serious damage to laminate flooring. They can cause not only abrasions on the coating, but also serious scratches and even chips. This is another reason why it is undesirable to use laminate flooring in the hallway.
- The claws of large pets can also cause deep scratches on the surface.
- Falling objects can damage not only the protective coating, but also the hard layer of the board, leaving a dent in it. Heavy or sharp objects are especially dangerous for this material.
Let's sum it up
This article will help you save time and money. After all, we all want to see a pleasant, well-groomed surface under our feet, without scuffs and scratches. And thanks to the fact that you know how to remove scratches on laminate using improvised means, the surface will be perfect.
Anyone who chooses laminate flooring should be prepared for the fact that sooner or later scratches will appear on it that will have to be masked. For this purpose, a special putty is produced for the laminate, with the help of which its cosmetic repairs are carried out.
Whatever one may say, such a floor covering cannot be called absolutely reliable, since it is not completely resistant to mechanical influences, especially abrasive and scratching ones. Even minor damage can be clearly visible. Moreover, a violation of the integrity of the coating in one place can often lead to further serious damage to the material over time. Therefore, if scratches or chips appear, they must be repaired immediately. In addition, in order to preserve the original condition of the laminated coating, it is advisable to treat it with a special agent immediately after installation.
How to protect laminate?
Is it possible to protect laminate flooring from the threats that lie in wait for it? Manufacturers of various protective products claim that yes, this is possible if special compounds are periodically applied to the floor covering.
Laminate coated with a special protective mastic shows higher resistance to abrasive and scratching loads on it
On sale you can find various types of mastics that are designed to extend the life of this coating while maintaining external decorative qualities.
One example of high-quality protective mastic for laminate flooring
The mastic is applied immediately after installing the coating on the base. Having completed laying the laminate, it should be cleaned of dust using a vacuum cleaner, and then a layer of protective composition should be applied to the surface. This treatment of laminate flooring should be done two to three times a year. In this case, the coating will acquire the following qualities:
- The joints between adjacent boards will become more resistant to moisture penetration.
- The strength of the laminate joints will increase.
- The surface will not accumulate static electricity, which means it will not attract dust and dirt. That is, contaminants will not linger on the coating.
- The laminate will be protected to a certain extent from abrasion and minor mechanical influences.
- Mastic can also restore the former shine to worn out old surfaces.
Mastic is produced in a colorless version or in different color shades. Therefore, it will not be difficult to choose the right color or even, if desired, make the coating a shade darker.
A product based on natural wax for treating the joints of parquet, natural boards or laminate.
Wax is used to strengthen the joints of the laminate, and is applied to the locks when installing the flooring. Using a wax composition will prevent moisture from entering the seams between the boards.
In addition, wax and wax-based putties are also used to repair chips and cracks.
How to repair cracks in parquet flooring
The appearance of cracks in laminated parquet can be due to various reasons:
- The initial choice is low-quality parquet. A cheap board or lining can lead to defects from temperature fluctuations or loads;
- Slats from different manufacturers may differ in size or shape of the locks. This incompatibility significantly affects the connection, which over time can weaken or stop fastening. When trying to join such lamellas, small gaps may occur.
- The most popular reason is installation on an uneven surface. Defects are not immediately detected, since the substrate softens and cushions for some time. But over time, it becomes denser and stops shock-absorbing, and the panels diverge.
Gaps between boards are not just a cosmetic defect. Their presence can deform the entire coating. Due to the fact that the protective film is broken and free access to the internal structure of the board is opened, without moisture-proof impregnation, the insides quickly become wet and deform along with the surface of the laminate.
Sealing cracks is carried out in several ways, depending on the number of cracks and sizes
How to eliminate cracks. If a gap forms due to unevenness of the base, it is necessary to replace the substrate. At the location of the defect, one or two boards are dismantled and the old substrate is carefully cut out. Unevenness of the substrate is eliminated, and wrinkles are removed. If the volume of the damaged substrate is large, then the entire lining should be replaced.
No less important information on the topic: Chips on the parquet
Not everyone knows that the durability and quality of the coating is, first of all, the merit of proper preparation and installation, as well as wisely chosen auxiliary material. There are many options to choose from:
- environmentally friendly and durable cork;
- polypropylene;
- polystyrene foam (for increased load);
- coniferous substrate, with good ventilation;
- on a foil base;
- polyethylene film;
- combined.
It is difficult to answer unequivocally which type of substrate is better. This depends on the conditions in which the coating is laid: humidity, subfloor (concrete or board), horizontal floor, etc.
Replacing the underlay will help eliminate the cause of the uneven floor.In cases where a radical method of replacing the substrate is not required, you can get by with cosmetic repairs. The cracks must be sealed to prevent liquid from getting inside. To do this, you can use a special putty paste, the procedure is as follows:
- It is necessary to remove debris and dust from the crack,
- tape around the edges,
- choose the color and apply putty,
- level with a spatula and dry,
- then remove the tape and wipe with a damp cloth.
You can do cosmetic repairs to scratches on laminated parquet yourself
Types of putties for laminate repair
In stores you can find a lot of products for masking cracks and chips in laminate flooring. Moreover, they are produced in different forms. All such materials can have different shades, which can differ by one or two tones or even differ significantly from each other.
An assortment of colors of wax bars for masking defects on laminate flooring.
Therefore, when going to the store, it is recommended to take a small fragment of the board with you so that the sales assistant can choose the exact shade to fill the crack. As a last resort, if a sample piece has not survived, you can take a high-resolution photograph, although such an image can often be deceptive.
The simplest remedy is a wax pencil. But it is only suitable for shallow surface defects.
- Wax pencil is used to mask cracks, crevices or shallow scratches. A restorative pencil is made from wax and polymers, which increase the adhesive properties of the composition when it adheres to the protective layer of the laminate. The crack must be thoroughly cleaned of dust, and then pressed over it with a pencil. The wax will fill the depression, after which the repaired area is polished until the coating returns to its original appearance.
Hard wax, usually sold in stick form, can be used to repair deeper defects in a laminate surface.
- Hard wax is sold in the form of bars that resemble plasticine. This material is convenient in that it can be used both in solid and molten form. In this case, different colors of wax can be combined with each other to achieve the desired shade, or, if necessary, darker colors can be applied to light putty. This type of wax can be used to repair deep scratches and chips in the decorative top layer of laminate flooring. In addition to wax, the bars may contain materials such as silicone, paraffin, various polymers, and dye.
- Mastic for laminate is used in cases where the surface is not fundamentally damaged, but has serious abrasions. It is applied with a brush and then rubbed with a soft cloth, or a small amount is poured onto the surface and then rubbed with a napkin.
Repair paste-mastic for laminate
- Laminate repair paste containing wax. This version of the formulations is sold in transparent tubes, which makes it easy to choose the desired shade. The convenience of this form of putty is that it does not have to be brought into the state necessary for application, since it already has the desired consistency. The paste is also produced in various shades.
Distribution of mastic or polish over the laminate.
- The polish, intended for tidying up the laminate, is used if abrasions appear on the surface of the coating, as well as after restoring the boards using a wax pencil, solid or molten putty. This restorative composition is sold in paste or liquid form.
Kit for deeper laminate repairs.
- To eliminate serious damage to the laminate, special kits are used, which may include putty, latex or acrylic compounds, wax pencil, etc. The composition of the kits may vary, so it is possible to choose the most suitable one.
The process of repairing a scratched area of laminate flooring
The procedure for repairing the laminate surface is completely simple and does not require special skills or expensive tools. However, in order for the result to be positive, when purchasing any of the products presented in construction stores, you must consult with the seller and also carefully read the instructions from the manufacturer.
For work, it is convenient to use the following devices: a wax melter, a special varnish with which the “felt-tip pen” container is filled, a wax spatula, the set of which includes additional devices - sponges, napkins, as well as a spatula cleaner.
A special tool for repairing laminated surfaces with hard wax - wax melter
The wax melter can have different designs and shapes. Homeowners whose floors are predominantly covered with laminate would do well to have this tool in their arsenal. By the way, it is useful not only for repairing floor coverings, but also for laminated surfaces of furniture.
Laminate repair kit.
The following will provide a step-by-step process for repairing a scratch on laminate flooring using Konig Super Hard Wax.
| Illustration | Brief description of the operations performed |
| Initial condition of the coating. In this case, a fairly deep scratch appeared on the laminate. Not only the protective layer of the board is damaged, but also the upper part of the base. | |
| In order for the putty to have good adhesion to the laminate, small fragments must be removed from the crack using a wax spatula with its sharp edge. At the same time, the scratch expands slightly. After which the recess and the surface around it must be degreased, for example, with alcohol, since the repair site must have good adhesion. Next, the scratch needs to be dried. | |
| The next step is to select the putty according to the color scheme. For this purpose, take several wax bars similar in color to the laminate. First of all, the base, lightest shade is selected, and to it one or two bars that match the tone. | |
| Now the wax melter comes into operation - this is a special tool that is convenient for repairing coatings. The device operates on batteries. | |
| The wax melter is equipped with a metal nozzle, made in the form of a spatula, which is temporarily protected by a cap. Before starting work, the cap is removed. | |
| Next, the button that activates the heating of the metal tip is pressed and held in this state for approximately 10÷12 seconds. | |
| Using a heated nozzle, the base wax putty melts. For such a scratch you will need a small amount. If the color of the putty is slightly different from the shade of the surface, then it is necessary to mix two or three colors of wax. As a rule, laminate does not have a single color, so sometimes the length of one scratch even requires changing the shade of wax several times when filling it. | |
| Fill the scratch with small portions of heated wax. Fill the scratch with excess, since the wax will shrink as it cools. If the tip of the wax melter gets very hot and the wax starts to smoke, you should release the heat-activating button to reduce the temperature. | |
| After each application of wax of a certain shade, the working tip must be cleaned with a clean cloth. | |
| After the wax hardens, after about 30-50 seconds, excess putty that protrudes above the surface of the coating should be removed using a wax spatula. | |
| To do this, use its ribbed side, which will not damage the main coating, but will gently remove excess wax. | |
| This operation is performed with rubbing movements across the repaired scratch. Do not press the spatula too hard. | |
| The result of the work will be a scratch covered with putty, which should look approximately as shown in the photo. | |
| If the scratch passes through darker or lighter veins, then putty bars of a suitable color are taken. The selection is also made by location so that the color is perfect. | |
| Next, a textured pattern imitating the structure of wood is applied over the filled scratch using the same heated tip of a wax melter. This stage of work requires care and high precision, since using a working tip you will have to try to recreate the original pattern of the laminate surface. | |
| After the putty hardens, its excess is also removed using a spatula. To do this, the protruding wax is wiped with the ribbed side of the instrument. | |
| Here the master shows what marks can remain on the spatula. After treating the surface, the spatula comb must be immediately cleaned with a napkin or a special device included in the kit, which is stored in the tool body. If the wax on the putty knife hardens, it will be difficult to clean and will interfere with subsequent work or when repairing other areas of the coating. | |
| The next step is to sand the repaired scratch with a gray sponge, which is also included in the spatula kit. | |
| Further, if necessary, the surface is additionally cleaned with the pointed side of the spatula. | |
| The next step is to coat the surface with a special varnish. It will protect the putty from dust and give the repair area the desired shine. A cylindrical container similar to a marker or felt-tip pen is filled with varnish. It is equipped with a brush, which is convenient for applying varnish to a small area of the coating. | |
| Before using the varnish, the pencil container must be shaken for 30-40 seconds, so that the knocking of the balls located in the container with the varnish and intended for stirring it can be heard. In order to ensure the purity of the applied varnish, it is necessary to remove the cap from the pencil and dip the brush in water. This is necessary to remove dust and loose fibers from the brush. A wet brush must be wiped with a clean cloth. Next, you need to press on the walls of the container to remove air from it. | |
| The pencil container must be held vertically and gently pressed in the area of the “PRESS” inscription. It is better to carry out this process over a napkin so that splashes of varnish do not fall on the surface of the floor covering. Then, if the varnish does not enter the tip, the container must be turned over with the brush down, placing a napkin under it, and press “PRESS” again. Excess varnish that appears must be wiped off with a napkin. Now a thin layer of varnish can be applied to the repaired lamella. When applying varnish, the brush must be periodically wiped on a napkin. | |
| To ensure that the shine of the area is commensurate with the main surface, it can be corrected using a polishing and sanding pad. | |
| The pad has two sides - white and green. Green adds shine to the surface, and white, on the contrary, serves to create a matte effect. Therefore, the surface is first treated with the white side of the material, and then, to give it a natural look, it is sanded with the green part of the pillow. | |
| These illustrations show the result of the work carried out. So that it could be assessed, the master showed nearby a scratch that had formed on the coating before it was repaired and after it was sealed with a complex of putties of different shades. |
It should be noted that some Internet users, accustomed to relying on their own ideas, offer other budget options for repairs. For example, using ordinary felt-tip pens or markers, you can give the scratch the desired shade, and fill the indentation with natural wax, melting it with a soldering iron. If necessary, the wax is melted and dye is added to it, and then applied to the damaged area of the coating. After hardening, the repaired scratch is sanded and varnished.
There are quite a lot of other home recipes, but all of them do not guarantee that the desired result will be achieved. Using untested means can completely damage the coating, which will lead to the need to replace several boards.
Industrially produced laminate repair products are designed taking into account the characteristics of protective coating materials. Therefore, they have excellent adhesion to the laminated surface, making the resulting defects almost invisible for a long time.
Find out about the reasons why laminate flooring creaks and methods for eliminating them from our new article on our portal.
However, each master chooses the most convenient and affordable method of repairing surfaces. Therefore, if you want to experiment, it is better to do it on a fragment of the laminate left after its installation, or, as a last resort, in an inconspicuous area of the coating.
Replacing a damaged board
Sometimes the damage to the flooring can be so severe that the laminate will need to be replaced. Fortunately, not all of it, but only that lamella on which there is a particularly large chip. To do this, you will need to purchase a strip of exactly the same color, as well as sealant and special vacuum suction cups. To cut laminate boards you will need a grinder.
This board will have to be replaced
On a note! The closer to the wall the damaged lamella is located, the easier it is to replace it - this can be done only by partially disassembling the floor.
Laminate flooring is usually assembled without the use of glue, but there are exceptions. In this case, it will be difficult to remove the damaged lamella.
Table. How to replace damaged laminate flooring.
| Steps, photo | Description of actions |
| Step 1 | Purchase laminate of a suitable color. Packaging with open ends is located inside the room where the replacement will be made for 7 days. This is necessary so that the material adapts to its future environment. |
| Step 2 | Using a pencil, the damaged lamella is drawn as shown in the figure. |
| Step 3 | Using a grinder, the lamella is cut into pieces according to the diagram. |
| Step 4 | In corner diagonal marks, the lamella is not completely sawn - about 4-5 mm remains to the edge. |
| Step 5 | Using a chisel and hammer, uncut areas of the lamella are finished. |
| Step 6 | Pieces of the lamella are removed. It is important to act carefully so as not to damage the locks of adjacent slats. |
| Step 7 | The surface of the subfloor is cleared of debris. |
| Step 8 | The lock on the new lamella is removed from one side (the one on the bottom). |
| Step 9 | Both side locks are also removed. |
| Step 10 | The lamella with a device holding it with vacuum suction cups is tried on the prepared place and then removed. |
| Step 11 | An adhesive composition is applied around the perimeter of the recess. |
| Step 12 | The lamella is installed in place and pressed with a weight. The drying time of the glue is about 30 minutes. At this time, you cannot walk on the slats. |
| Step 13 | Remaining glue is removed with a spatula. Then the lamella is pressed down again with a weight and dried for about 12 hours. |
Replacing laminate boards
Video - Replacing a laminate panel
Which putty is better?
The domestic market offers a sufficient range of various materials for repairing and maintaining the laminate surface. Almost all of them do an excellent job. One of the most important points to achieve the desired result is choosing the right shades of wax or other repair products.
The most popular materials for laminate restoration are German and Dutch “Quick-Step” products. Both companies produce putty in the form of paste, wax bars and pencils, as well as in special kits.
Repair kit “Quick-Step Mix & Fix” for repairing scratches on laminate and parquet.
Companies present on the market 24 shades of wax putties that mix well with each other. Therefore, if desired, you can achieve any color that will effectively mask the flaws that have appeared.
A mixture of sawdust and gypsum
A good option for repairing a chip is a composition of sawdust and gypsum. Both components are mixed with water in equal quantities to a homogeneous paste. A large chip can be preliminarily repaired with a tab, the role of which can be perfectly fulfilled by a wooden sliver of a certain size. The inserted wood chips are carefully covered and rubbed with a composition of sawdust and gypsum.
Instead of plaster, you can use PVA glue:
- sawdust is mixed with glue until a homogeneous mass is obtained;
- the mixture is applied to the chip;
- after complete drying, it is necessary to remove excess;
- level the repair site with putty matched to the color of the laminate;
- If desired, the laminate can be varnished.
Epoxy resin has two components: a resin and a hardener. They need to be mixed, following the proportions according to the instructions, until an elastic, homogeneous mass, using a drill with an attachment. Mixing must be carried out for at least 5 minutes at a temperature of at least 15 degrees. The resulting composition is evenly applied to the pre-treated chip.
How to avoid defects on a laminated floor surface?
Having chosen a laminated covering for flooring in an apartment or house, you should immediately provide for its protection. It would be a good idea to do this after the surface has been repaired, so that you don’t have to work on scratches and chips again.
These activities are simple and consist of the following steps:
- When cleaning the coating, do not use detergents containing abrasive ingredients.
- If laminate is laid in the hallway, then you should definitely lay rugs on both sides of the front door, that is, outside and inside the home.
- To protect the laminated covering from the wheels of the office chair, it is recommended to lay a thin but durable flooring that fits well to the surface in the area where it moves. This can be a rubber-based mat or acrylic glass.
Acrylic glass as protection of the floor covering from abrasion by the wheels of an office chair
- It is also necessary to protect the laminate from the legs of furniture, especially those that are frequently moved (chairs, tables, stools, etc.). To do this, felt, vinyl or polyamide pads are glued to the ends of the legs.
- You must remember to periodically use polish or mastic for laminate flooring to treat the surface. These products create a protective film on the coating, which additionally protects it from minor mechanical influences.
Check out the tips for homeowners on how to choose a laminate flooring class from our new article on our portal.
* * * * * * *
As you can see, there is nothing complicated about preventive measures - they are easy to implement. If you don’t want to make certain efforts to preserve the laminate flooring, then you should immediately abandon the idea of choosing this particular material. Without proper care, it will quickly become unsightly or even completely unusable.
At the end of the publication, there is a video in which the master shows a slightly different method of repairing a laminated surface.
How to remove or disguise cracks
After finding out the causes of damage to the laminate, you can safely begin to choose a method for eliminating them. The first situation to consider is the most common, namely, after a couple of months, gaps between the laminate panels became noticeable on the floor. What to do in this case?
There are several ways to solve the problem. Each option differs in its effectiveness, but has differences in the complexity of the process:
- If it turns out that the cracks arose due to an uneven base, then you can do something drastic and level the floor.
- To do this, it will be necessary to disassemble the laminate and remove the backing, which has probably already become worn out and cannot be reused. Next you need to level the floor under the laminate. To ensure quick leveling, you can use a self-leveling mixture. After it dries, a new substrate is laid on top and the laminate is re-laid.
Note. This method is only suitable if the panels were not coated with special glue or sealant during initial installation.
If there is no opportunity or desire for global work, you can use a partial solution, but you will still have to dismantle the laminate. Next, a denser underlay is immediately laid under the laminate and the floor covering is installed. This will only bear fruit in case of minor unevenness.
TOP of the best mastics and sealants for laminate flooring in large containers
Vici Lux
A characteristic feature of this model is its low consumption of substance. You will need no more than 25 g of the composition to cover 1 m2 of working surface. It is rightfully considered one of the best mastics present on the domestic market. It is based on the use of wax, which is suitable for any wooden floors and products. Easy to apply due to optimal consistency. It does not spread over the surface and does not leave stains. Despite the high cost, it should be noted that one can is enough for a large amount of work, due to its economical consumption. You can order online, directly from the manufacturer’s website or in any construction market.
Cost – 2490 rub.
Vici Lux
Advantages:
- numerous positive reviews;
- economical consumption;
- ease of use;
- consistency;
- professional quality.
Flaws:
- none.
Neomid SuperContact
This product is characterized by high quality and thoughtful composition. Can be used to treat laminate and other surfaces. The presence of a one-component composition deserves special attention. During the application process, smudges and stains do not appear. No experience is needed to work with the substance. It is enough to read the instructions supplied by the manufacturer. To avoid mistakes when choosing, it should be noted that the composition has good antiseptic qualities. It is recommended to order through trusted online stores. This eliminates the risk of buying a counterfeit product.
How much does the packaging cost? The purchase will cost 1410 rubles.
Neomid SuperContact
Advantages:
- antiseptic qualities;
- ease of use;
- the composition belongs to the category of one-component;
- universal purpose;
- functionality;
- positive reviews;
- safety;
- value for money.
Flaws:
- not available in small containers.
Forbo Eurocol Euroclean Longlife
This popular model belongs to the category of wear-resistant and, at the same time, universal mastics, which are in high demand among professionals. Suitable for treating various surfaces, including laminate. Suitable for treating floor coverings with increased trafficability. After the composition dries, a thin protective layer is formed that effectively protects the coating from moisture. After drying, the material does not become slippery. Sufficient resistance to abrasion appears.
Cost – 1030 rub.
Forbo Eurocol Euroclean Longlife
Advantages:
- drying speed;
- ease of application;
- universal purpose;
- wear resistance;
- practicality;
- value for money;
- numerous positive reviews.
Flaws:
- not identified.
Bagi For floor polishing
This inexpensive and, at the same time, high-quality model is designed for polishing parquet, wood and laminate. After drying, the substance forms a protective coating that allows you to extend the service life of the floor covering and protect it from moisture. The pleasant aroma, which disappears soon after application, deserves special attention. This eliminates the need for prolonged ventilation of the room and work in a protective suit.
Average price – 668 rubles.
Bagi For floor polishing
Advantages:
- wear resistance;
- drying speed;
- numerous positive reviews;
- pleasant aroma;
- safe composition;
- protective qualities.
Flaws:
- none.
Almira Mastic universal
This composition belongs to the universal category, and is suitable not only for working with laminate, but also other materials. The thoughtful composition, which does not contain harmful and dangerous impurities, deserves special attention. The smell is neutral, which eliminates the need to work with a respirator. It is also worth noting the increased heat resistance coefficient. It applies well due to its optimal consistency. Cold resistance is also noted.
How much does the container cost? The purchase will cost 148 rubles.
Almira Mastic is universal
Advantages:
- absence of unpleasant aroma;
- safe composition;
- resistance to low temperatures;
- universal purpose;
- positive reviews;
- practicality;
- functionality;
- affordable purchase.
Flaws:
- high consumption.
Bitumast colorless
This product from a renowned brand is designed for treating floor coverings. Its base is colorless. After complete drying, the composition becomes invisible to prying eyes, which has been repeatedly noted in reviews. It should also be noted that there is no specific aroma, which will allow you to work without protective equipment. This was achieved by adding a flavoring based on orange oil to the composition.
Average price – 109 rubles.
Bitumast colorless
Advantages:
- pleasant aroma;
- colorless base;
- ease of use;
- economical consumption;
- numerous positive reviews.
Flaws:
- difficult to find in stores.
