All the lights on the Indesit washing machine are flashing - what to do

Long gone are the days when you washed and rinsed clothes by hand. Reliable household appliances have become part of the everyday life of the modern housewife. It is not surprising that when the Indesit washing machine does not work, it causes confusion and sometimes panic. Do not get upset prematurely; randomly flashing indicators do not always indicate a serious breakdown. Whether you can deal with the problem yourself or whether you need the help of specialists, the error code will tell you.

The meaning of the code

According to established tradition, we will begin with a general decoding of the error code, in this case code F12; such a decoding can be found in the operating instructions for the Indesit washing machine. And then we will provide a more detailed transcript, which will finally shed light on the problem. So, the general interpretation of error code F12 can be presented as follows: “the control module has stopped interacting with the buttons and lights of the control panel.”

Essentially, in this case, the Indesit washing machine states that there is no connection between its two most important modules. However, the connection was not completely lost, since the module was able to transmit information about the error to the user, which means that the electronic module retains some control over the control panel. Despite this, error F12 is accompanied by the inability to use the control panel in any way; in rare cases, even the on/off button does not work.

How and under what circumstances does it manifest itself?

If the Indesit washing machine does not have a display, then the electronic module (bypassing the usual circuit) will connect some control panel lights, which, in fact, will indicate an error. We are talking about the “Super Wash” and “Wash Delay” indicators that are on. On some models of Indesit washing machines, only the speed indicator may blink.

Error F12 in 99% of cases appears shortly after turning on the machine to the network. In this case, the user does not yet have time to select any washing program, or indeed do anything with the control panel. The Indesit washing machine freezes immediately, in addition, the on/off button may fail and then you will have to turn off the power to the machine by unplugging the power cord from the socket.

We find and eliminate the causes

The malfunction caused by error F12 can often be eliminated by restarting the Indesit washing machine. Moreover, the reboot should not be done anyhow, but according to the following scheme.

  • We turn off the washing machine with the on/off button if it is working.
  • Disconnect the power cord of the Indesit machine from the power supply.
  • We wait for 2-3 minutes.
  • We turn on the machine to the mains and press the on/off button.
  • If the error persists, repeat the above steps two more times.

If the malfunction has not been resolved within 3 reboots of the machine, such actions should be stopped so as not to damage the control module even more. If rebooting does not help, it means that a serious breakdown of the control module has occurred, or the contacts connecting the module and the control panel bulbs have oxidized. With such a problem, there is little that can be done on your own. Unless you check connector J11, which, as you may have guessed, connects the display module to the control board.

If, after cleaning the contacts of connector J11 and the display module, the Indesit washing machine does not start working correctly, then the problem is in the control module. Perhaps the question will immediately come to your mind: is it worth doing repairs of electronic modules yourself? We will answer briefly - it’s not worth it! Most often, this ends in the final breakdown of the washing machine and the user being forced to contact a service center. Just keep in mind that the repair will cost 2-3 times more, since you will definitely have to change the spare parts of the “home assistant”, and this is completely different money.

So, a malfunction caused by error F12 can be eliminated only if the control board is not damaged, but only the contacts are burnt or oxidized. If the module breaks down, definitely contact a technician. Good luck!

What does it mean?

Blinking of all the indicators on the washing machine is a common problem with washing machines from Indesit. Owners of such washing machines most often turn to the technician, not knowing what to do. What causes this blinking?

The most common malfunction, when all the lights blink, is a malfunction of the electronic board, or rather a breakdown of its parts. As a rule, capacitors located on the board fail or contacts burn out when water gets on the board. It is quite possible to replace capacitors yourself, especially if you are good with a soldering iron. In some cases, the board has to be changed completely, which requires significant financial costs.

For your information! Replacing capacitors will save your budget by a large amount, the main thing is to correctly diagnose the breakdown.

This is interesting: How to lengthen the hose of a washing machine: extending the drain and inlet hoses

Other reasons for program crashes and blinking indicators

The LEDs on the control panel may blink not only due to a breakdown, but also due to incorrectly set parameters. There are a number of washing modes that provide the ability to connect additional functions:

  • additional rinse
  • higher degree of water heating,
  • ironing

Instead of turning on, the indicator may flash if the selected program cycle does not provide a particular function.

The machine can generate a service error both at the initial stage of washing and during it. In cases where the weight of the load of laundry is not comparable to the number of revolutions or the maximum allowable volume of laundry provided for by the technical specifications, the spin process may not start. In this case, the buttons indicating a failure in the “Rinse” and “Spin” modes and the door lock indicator will start flashing. At this moment, it is necessary to restart the machine a second time, reducing the number of things.

After this, the execution of the specified program will stop. After a few seconds, the door will unlock, allowing you to make adjustments and start washing.

How to prevent breakdowns in the future?

In order for your washing machine to last as long as possible without breakdowns, you need to take proper care of it.

Basic recommendations:

  1. Monitor the integrity of hoses and cables.
  2. Avoid getting moisture on parts.
  3. Clean the powder receptacle regularly.
  4. Remove moisture from the cuff.
  5. Protect the device from power surges by using a power adapter.
  6. Stop washing if the water pressure drops or if there is a power surge.

Common breakdowns when the lock on a washing machine blinks

According to the experience of the RemBytTech workshop, there are a number of typical washing machine malfunctions that are accompanied by the lock blinking.

Symptoms of a problemPossible breakdown and solutionRepair price* (labor + spare parts)
The lock icon flashes on the body or display of the machine, but the hatch does not lock or, on the contrary, does not open after washing. Other indicators may also flash or an error code may appear on the display. Damage to the electronic sunroof locking device.

It needs to be replaced.

from 3400 to 4700 rub.
The door does not close, the tongue on the hatch does not fit into the hole. At the same time, the lock indicator blinks. Broken door lock due to mechanical damage.

Replacement of damaged parts or the entire lock is required.

from 2200 to 4700 rub.
Skewed hatch hinges due to mechanical impact on it (for example, a child rolled on the door).

Hinges need replacement.

from 2500 to 3900 rub.
The lock (key) indicator and the car blink:
  • freezes during washing;
  • washes but does not heat water

In addition, the washer may show an error code.

The tubular electric heater (TEH) burned out.

It needs to be replaced.

from 3500 to 5900 rub.
The machine “confuses” the washing programs or the washing does not start at all. The problem is accompanied by flashing door lock indicators. Malfunction of the program selector or breakdown of the entire control module.

The selector or the entire board needs to be replaced.

Repair - from 2200 to 4900 rubles.
Replacement - from 5400 rub. (including the cost of a new module)
The key (lock) indicator on the car body blinks. The machine does not spin the drum and makes noise. An error code may be displayed. Wear of motor brushes.

They need to be replaced.

from 3200 to 4400 rub.
Washing machine
  • doesn't dial
  • constantly fills and drains water
  • stopped with water while the program was running.

The lock icon blinks on the display. Additionally, other indicators may flash or an error code may appear.

Damage to the water level sensor (pressostat).

You will need to check the pressure switch tube for blockages or replace the sensor with a new one.

from 1500 to 3800 rub.

* Approximate PRICE OF TURNKEY REPAIR including the cost of spare parts and work of a specialist. The final cost of repairs will become known only after a specialist diagnoses the problem.

To summarize, it should be said that the flashing of the lock/key in itself does not indicate any specific problem with the washing machine. Therefore, you need to rely on additional symptoms that will help determine the range of possible malfunctions. For example,

It should be remembered that only a qualified specialist can determine exactly what happened to your washing machine after diagnostics. Therefore, if the machine has stopped functioning normally, and the lock on its body or display is lit or flashing, do not experiment or try to repair it yourself unless you are a master. This can lead to even more serious damage.

Contact the specialists of the RemBytTech workshop:

Within 24 hours after contacting, the technician will come to your home, conduct diagnostics and, if necessary, repair the washing machine. All work and spare parts are guaranteed for up to 2 years.

If your washing machine breaks down, don’t expect a miracle. Call “RemBytTech” right away!

Indicators do not light up, machine does not work

If the washing machine does not turn on, the indicators do not light up or blink, check to see if the electricity supply in the room has been cut off. Also, if the functions do not work and the lights do not light up when turned on, check:

  • Power cord. It may have been damaged or choked.
  • Fork. Its body could have melted, or the contacts could have come loose.
  • Connect another device to the outlet to check its functionality.

Regardless of the brand of washing machine, if you have electrical problems, call a specialist. You should not fix such problems yourself.

If you notice flashing lights when you turn on your washing machine, the first thing to do is find out what the fault code means. Then you will understand whether you can fix the problem yourself or whether you will have to contact a service center.

Error codes indesit w 105 tx

The displayed fault codes for Indesit washing machines are presented in Table 1.

Table 1 - Errors, their names and possible causes

  1. Indication on the display of an error that has appeared
Decoding the information that appearsReasons for the malfunction
F 01Short circuit (short circuit) in the motor control circuit1) The triac responsible for: turning the electric motor on and off has failed; regulation of its speed. 2) Short circuit of contacts on the connector due to water ingress.
F 02Lack of feedback from the tachogenerator1) Break in the supply wire to the motor. 2) Broken motor stator winding. 3) Tachogenerator malfunction. 4) Lack of contact with the controller board.
F 03Temperature sensor is faultyNo change in water temperature. 1) The temperature sensor is faulty. 2) The heating element is faulty. 3) Lack of contact in the heating element relay.
F 04Double signal on the pressure switchThe controller receives two signals about a high water level, at which the drain valve opens, and about insufficient water, at which the water supply valve turns on. Malfunction of the sensor that monitors the water level in the tank.
F 05No empty tank signal1) Drain pump failure. 2) The drain line is clogged. 3) Malfunction of the sensor responsible for monitoring the water level in the tank.
F 06Mismatch when choosing a washing program1) The pre-dial code from the washing mode selection button does not match the controller parameter.
F 07Insufficient water level to turn on the heating element1) There is no signal from the pressure switch about filling the tank. 2) The heating element is faulty. 3) Contact sticking in the heating element.
F 08Working heating element while draining water1) Malfunction of the pressure switch. 2) Contact sticking in the heating element relay.
F 09Error in the operation of non-volatile memory installed on the “EEPRO M” controller board1) Failure of the PROM - a rewritable programmable storage device (non-volatile memory).
F 10No signals from the pressure switch1) Malfunction of the pressure switch. 2) Lack of contact with the controller board.
F 11There is no power to the drain pump1) Broken winding in the motor. 2) Malfunction inside the unit.
F 12No indication1) The display board is faulty. 2) Lack of contact between the controller board and the indication board.
F 13No signal from the clothes drying temperature sensor (only for machines equipped with this function)1) Sensor malfunction. 2) Lack of contact.
F 14No heating of the heating element in the clothes drying mode1) Malfunction of the heating element. 2) The power circuit is broken.
F 15The drying mode does not turn off1) Contact sticking in the heating element relay. 2) The control circuit is broken.
F 16Stopping the drum not in the upper position (for machines with vertical loading)The drum loading door must be at the top. 1) Lack of power. 2) Failure of the stop control system.
F 17Loading door is not closed1) No power to the door lock. 2) Damage to the lock mechanism.
F 18Internal controller error1) There is no connection between the controller board and the executive control board.

As can be seen from the table, for each error information there are several reasons for its occurrence. And as a result, the light warning shows the direction in which to start troubleshooting, which significantly saves the time of service workers and reduces the time the washing machine is under repair.

Troubleshooting and troubleshooting

If you are well versed in technology, then you can figure out all the problems yourself. You can check the condition of the electronic board and fix breakdowns at home, but first you will have to disassemble the unit.

To do this you need to do the following:

  • de-energize equipment;
  • remove the housing cover;
  • unscrew the hex screws holding the control board;
  • disconnect all wires from the connectors;
  • change the capacitors (or the board itself).

In front-loading Indesit models, the electronic board is located at the bottom of the rear. Getting to it won’t be difficult if you have the most common tools. For diagnostics, it is better to use a multimeter, which can be used to “ring” capacitors and contacts.

Unwinding the case usually does not cause problems, but each model has its own design features. The control panel is mounted with two bolts at the back, and the electronic board is held in place with small screws.

Top-loading models have the electronic control panel at the top, while front-loading models have it at the lower rear.

When externally examining the electronic board, look for capacitors that have a round shape. Particular attention is paid to capacitors C16, C17 (capacitance from 680 mF to 1000 mF), C20. If they fail, they usually start to swell at the top. To accurately diagnose a breakdown, you can “ring” them with a multimeter. When replacing capacitors, you must carefully check the markings to select the exact model for your washing machine.

Why do all the lights on my washing machine blink?

It doesn’t matter: two indicators flash or all at once - this already indicates abnormal operation of the device. Most often, such a problem occurs with equipment.

If you have this particular model, take a look at the instructions. There is a decoding of the code that the system issues.

There are a number of standard situations when equipment produces indicator signals. Check:

  • Is the water supply valve open? Unscrew it all the way. It is possible that water is not flowing due to a clogged mesh filter, intake hose or filter.
  • Is the waste fluid draining normally? Remove the blockage in the drain hose and restore its correct location.
  • Condition of the power cord. If damaged, replace it.
  • Drum load. It should not exceed the norm specified in the instructions. Stop work and take out some of the laundry.
  • Connection to sewerage. If the drain hose is located near the floor, the water drains out of the tank by itself. Raise it to a level of 40 cm from the floor.

If the red light of the lock is constantly blinking, the reasons may be the following:

  • There is no water in the system, low pressure in the line.
  • The loading hatch is poorly closed, the door lock did not work. Press the door tightly until it clicks.
  • A power outage caused the electronic module to fail. Disconnect the equipment from the network for 10-15 minutes. After turning on, press the start button and the machine should resume operation.
  • Child Lock is enabled. Press the button again to release the lock.

Have you ruled out all situations, but the indication has not disappeared? This may indicate breakdown of components and parts. For example, if the lock and rinse indicator blinks in an Indesit automatic washing machine, the motor may have broken down. We will consider breakdowns requiring repair below.

All indicators are flashing, the SMA does not turn on. What to do?

The main cause of failure is the control board. Its contacts, capacitors, and resistors could burn out. In this case, the machine does not work, all the buttons light up. You can inspect the board yourself:

  • De-energize the SMA;
  • Unscrew the top cover bolts from the back;
  • Slide it back and remove it;
  • Remove the detergent tray;
  • Remove the control panel bolts. The module is mounted on it, and inside there is a board;

The module cover is removed after unfastening the latches or unscrewing the screws;

Inspect the board. Noticed burns or oxidation? Take the part for repair. The element is expensive, and its repair requires special skills.

What other malfunctions are there?

Hatch lock

The red lock indicator light is on.

The hatch does not lock or does not open after the end of the cycle. Check the hatch locking device (UBL). For this:

  • Remove the cuff clamp;
  • Unscrew the two UBL mounting bolts;
  • Bend the cuff, put your hand behind the body;
  • Get the lock out. If burn marks are visible, replace the device. Disconnect the wiring and install a new element.

Door lock

The lock indicator lights up, the door does not fit tightly, the latch does not fit into the hole. Inspect the hinges; they may be warped. Tighten the fastening screws. If the lock tongue is broken, you need to disassemble the door and change the mechanism. How to do this, watch the video:

A heating element

Did the “service” and “lock” indicators light up? It looks like the heating element is broken. In this case, the SMA may freeze in the middle of the program or wash with cold water. If you see a flashing “service” button, check the heating element.

It can be located in the front or back of the case. Details of the replacement are described in the article “How to connect a heating element in a washing machine.”

Level sensor

The lock is blinking on the screen. Water does not fill into the system, it is constantly drained, and the SMA slows down in the middle of the cycle. Check the pressure switch hose for blockages.

Remove the top cover. At the side wall you will find a pressure switch;

  • Disconnect its wiring and disconnect the hose;
  • Connect the tube in place of the hose;
  • Blow into it;
  • Do you hear clicks? This means the device is working. If not, replace it.

Motor brushes

Above we described how the indicators behave in the event of an engine malfunction. You may also hear extraneous sounds and notice sparking.

The motor brushes transmit electricity to the rotor to spin and operate the motor. Over time they wear off. Replacement is easy, the main thing is to select suitable elements for installation.

  • Remove the rear cover of the SMA by unscrewing the bolts around the perimeter;
  • Below you will see the engine. Disconnect its wiring, unscrew the bolts;

Remove the brushes from the housing. They are connected to the motor with a wire that needs to be disconnected;

Install new elements in reverse order.

Have you noticed any blinking lights on the control panel? Now you know what to do to fix the problem. If self-repair is not possible, contact a service center.

We find and fix the problem

To check and make sure that the electronic board is faulty, you need to remove it from the machine, which will have to be disassembled. Let's consider this process using the example of a top-loading washing machine from Indesit.

The first thing we don’t forget to do is turn off the power to the washing machine . We begin disassembling the machine body by unscrewing the control panel, which is attached to two bolts on the back of the case. Having removed the control panel, we unscrew the hex screws holding the electronic board.

Note! In an Indesit front-loading washing machine, the control board is located in the lower corner at the rear of the machine body.

Now carefully disconnect all the wires from the board. Before doing this, you can take a photo, which will make it easier to figure out all the wires and connect them back.


We take the board and carefully inspect it, paying special attention to capacitors C17, C16, C20. If it fails, the top of the capacitor may swell.

Important! It is best to “ring” the capacitors with a multimeter, because if one of them is dry, then it will not work, although it does not look different from a working capacitor.

We remove the faulty capacitor and look at the markings on it, using it you need to find a similar one. You can buy a new one, or remove the working capacitor from the circuit board of an old TV, USB charger, etc. Next, we solder a working capacitor onto the board, and then assemble the washing machine.

For your information! Instead of capacitor C17 with a capacity of 680 mF, you can install a capacitor with a capacity of 1000 mF.

The entire process is captured in more detail in this video.

Rare causes of blinking indicators

However, the described malfunction is not the only one that causes all the machine’s indicators to blink. Masters note a number of other reasons. Despite the fact that they occur less frequently, they should not be excluded.

  • The water has drained out.
  • The heating element for heating the water or the heating element for drying is broken.
  • The electric motor has failed.
  • Damage to the pump (drain pump).
  • The command apparatus (KSMA) is out of order.

The heating elements of a washing machine wear out over time and fail. Their failure can stop the normal operation of the washing machine and cause the indicators on the control panel to blink. To establish this reason, you need to check with a multimeter whether the heating element is working, and if it malfunctions, replace it. A detailed description of this work is presented in the article on how to check the heating element of a washing machine.

An electric motor does not fail often; its breakdown may be associated with worn brushes, which can be replaced to restore its functionality. A more common problem is that the drain pump is broken or clogged. Very often, hair and fur get wrapped around the pump impeller, causing it to not work. In this case, it is enough to clean it of debris. If a more serious breakdown occurs, you will have to replace the pump with a new one.


As for the breakdown of the mechanical command device, this malfunction is very rare, since this part of the machine is one of the most reliable, but not eternal.
Usually the contacts in the command device burn out. To fix the problem, you need to clean them well and reconnect them.
The unit itself is located under the control panel, which is held in place by one or two bolts. In addition, the gear may break in the KSMA. And then troubleshooting will depend on the model of the washing machine, because in some “washing machines” you will have to completely change the KSMA, in some there is the possibility of repair.

So, flashing lights on an Indesit washing machine are not a reason to say goodbye to the unit forever and look for a new replacement. After all, the reason for the light indication may be simple and does not require large financial investments. Therefore, before you panic and think that the machine is broken, carry out diagnostics , we hope our article will help you do this.

Causes and diagnosis

Even if the “F01” error occurred for the first time, it is necessary to carry out diagnostics and understand the cause of its occurrence.

The following circumstances may lead to malfunction:

  • voltage drops in the network;
  • breakage of the socket, plug or cord;
  • physical wear of motor brushes;
  • corrosion of electrical circuit contacts;
  • malfunctions of the washing machine components;
  • control board failure;
  • turning the washing machine on and off during operation.

One of the possible causes of the failure is resetting the programmed settings. In this case, it is better to force a reboot of the machine:

  1. Disconnect the device from the electrical network.
  2. Leave for 30 minutes.
  3. Insert the plug into the socket.
  4. Start the machine.

If the reboot does not help, you will have to start troubleshooting, sequentially analyzing the operation of the nodes

There is a problem with the outlet, plug, or cord

Very often, the cause of the F01 code is an unstable voltage supply due to damage to the socket, cord or plug.

They need to be inspected, integrity checked and made sure there are no scorched areas indicating broken contact. In addition to a visual inspection, it is necessary to take measurements using a multimeter.

Mains voltage

Before you begin diagnosing a problem in the washing machine itself, you should check the voltage in the network. According to the rules, it should be 220V. It is this indicator that household appliances, including the Indesit washing machine, are designed for.

If the voltage in the network fluctuates, then the operation of the washing machine should be organized through a voltage stabilizer. This will extend the life of the equipment and reduce the likelihood of failure due to a short circuit.

Broken or stretched drive belt

The belt in the washing machine ensures that the drum rotates, which is provided by the motor.

If the belt has slipped, torn or stretched, it either does not perform its functions or performs it intermittently.

To verify the condition of the unit, you need to remove the back panel of the washing machine and gain access to the belt.

The worn part must be replaced with an identical one (all the necessary information is located directly on the belt itself) or, if it has simply fallen off, its correct position must be restored, paying attention to the grooves and pulley

Engine problems

Access to the engine can be gained through the service hatch - it is located on the rear wall. You can check the engine's performance after removing the element.

To do this, perform the following steps:

  • remove the back wall;
  • remove the drive belt by loosening the pulley;
  • carefully disconnect the wires leading to the engine;
  • remove the engine.

When disconnecting wires from the engine, it is very important not to forget which ones are attached where. To avoid confusion, it is recommended to draw up a contact diagram before removing the part. Diagnostic algorithm:

Diagnostic algorithm:

  1. Inspection of carbon brushes. Over long periods of use, these parts tend to wear out. When worn out, they should be replaced with new ones.
  2. Inspection of contacts. The problem can be caused by both dust and the smallest fractions of coal.
  3. Checking the motor winding. In addition to visual inspection, it is necessary to use a multimeter to determine the resistance; this indicator should be in the range from 20 to 200 Ohms.
  4. Inspection of the condition of the collector lamellas.

Corrosion of washing machine parts is not a rare situation. This is explained by the specific location and operation of the device itself - with the presence of moisture.

Metal elements, including the engine, are susceptible to corrosion. If the defects cannot be eliminated, the engine requires replacement.

Control module problems

The control module is the “brain” of the machine. This is one of the tricky parts. Some defects are noticeable to the naked eye and can even be eliminated on your own.

For example:

  • condensation that has appeared and requires drying;
  • dark spots - they can be wiped off with an alcohol-containing product.

It is best to entrust a specialist to carry out high-quality diagnostics and troubleshoot problems in this element, since correction requires not only special skills and knowledge, but also a suitable tool.

You can see how the module’s state is analyzed in the video:

How to fix the problem?

You can fix simple defects in your Indesit washing machine yourself. Only individual breakdowns that affect the control module should be resolved with the assistance of a specialist. The cause of the problem is not always a mechanical problem. For example, the electronic control unit of a washing machine may freeze due to power surges. Repair of the unit should begin with the elimination of this error. To do this, just unplug the device from the network for 20 minutes and turn it on again. If this does not help, then the cause of the malfunction lies in something else.

  • The electric motor is faulty. First you should check the voltage in the electrical network and the serviceability of the socket or cord. Due to frequent power surges in the network, electrical mechanisms deteriorate. If there are problems with the motor, then you need to open the back panel and inspect for wear of the brushes, windings and check the serviceability of the triac. If one or more elements are faulty, they should be replaced.
  • Problems with the heating element. Owners of Indesit brand devices quite often encounter this situation. A typical breakdown is the failure of the electric heating element due to excessive accumulation of scale on it. The element should be replaced with a new one.

Manufacturers have thought through the placement of the heating element, and getting to it is quite easy.

There are other problems too. It is worth knowing what to do in an unpleasant situation.

  • Sometimes the unit stops draining water. You should check whether there is a blockage in the filter or hose, whether the impeller blades are jammed, and whether the pump is working properly. To eliminate the breakdown, you need to thoroughly clean the filters, blades and hoses of debris.
  • The control board is faulty . It is often impossible to fix this breakdown on your own: you need quite serious knowledge in the field of radio engineering. After all, in fact, the unit is the “brain” of the washing machine. If it breaks, it usually requires a complete replacement with a new one.
  • The loading tank lock refuses to work. Most often, the problem lies in trapped dirt, from which the element must be cleaned. The locking device has contacts, and if they are dirty, the door does not close completely, the signal does not reach the other components of the device, and the machine does not start washing.
  • The SMA begins to fill in water for washing and immediately drains it. The triacs that control the valves fail. They require replacement. With this problem, it is best to contact a household appliance repair specialist.

We determine the error code using the indicators in the video below.

Kandy washing machine errors without display

To read errors on a washing machine without a display, you just need to count the number of flashes. Here the following must be taken into account: if a code starts to appear, the indicators blink at intervals of 0.5/1 second, and the interval between the end and the beginning of the error lasts about 5 seconds. So that you understand what happens next, for example, let’s take a code with five flashes, that is, the indicators blink 5 times, then a 5 second pause and again they should blink 5 times, then again a 5 second pause, repeating about 10 times. I think I explained it clearly, now you can sort out all these codes in order. Photo of a Kandy washing machine without a display

The error code is determined by the blinking indicator. The number of flashes in a series corresponds to the numerical value of the code in the table. The pause between series lasts 5 seconds
How many times does the diode blinkWhat does this error mean?
If the board is constantly on, then the matter is slag. Most likely the problem is in the control module → call a technician
1Corresponds to code E01, that is, the hatch door is not tightly closed. You can read more about this error in the table above.
2Corresponds to code E02 → indicates a long intake of water or no water at all
3E03 → drain system malfunction. We look at the pump, clean the filter, pipe and drain hose
4E04 → too much water in the tank. In the table above, I talked about this problem well, look for this code and read
5The temperature sensor is broken or shorted. First of all, you need to check the contacts and wiring. The temperature sensor or, as it is also called → thermistor, fails extremely rarely, but it is advisable to check it. Check the heating element at the same time
6Memory failure on the electronic control module. It is clear that without an experienced craftsman, you cannot fix this problem with your own hands.
7E07 → problems with engine operation. We check the tachometer, brushes, contacts, wiring and in general everything related to the rotation of the shaft on the motor
8E08 → Look at point 7, it’s practically the same thing
9Another error related to the engine, but it specifically indicates a seemingly burnt triac. Of course, it’s good that brains point to this detail, but we need to check everything that I wrote in paragraphs 7 and 8
12The connection between the control boards is interrupted → you can’t fix this error yourself, call a technician. Although, for starters or for your own self-satisfaction, you can ring the wiring and check the contacts
13See point 12, it’s no different at all
14The control module is covered → call a technician
15Program failure → the error is associated, to a greater extent, with the control module, one might even say with its memory. From experience I can say that, as a rule, a simple flashing does not give any results, that is, the control unit needs to be repaired
16The washing machine did not heat the water, corresponds to the error code → E05 In the table above, I described this malfunction in detail. We check the heating element, temperature sensor, heating element relay and wiring
17Malfunction of the hall sensor, that is, the tachogenerator. Although the error points specifically to this part, everything related to the rotation of the motor shaft must be checked. Simply put, the control module does not see that the motor armature is spinning
The manuals say that this error means the control module is faulty. Yes, in most cases, this is exactly the case, but often this code appears when the voltage in the network is higher or lower than the specified parameters, so first of all, you need to measure the current in your outlet, and then draw conclusions

You put things in the drum and started the program, but after a while you discovered that the Kandy washing machine stopped washing, did not spin the drum and displayed code E08 on the display. Before stopping, you may have observed one of the following signs:

  • the drum of the machine rotated for a short time at high speeds (right with water immediately after turning it on);
  • the drum rotated only in one direction - clockwise or counterclockwise;
  • The SMA did not rotate the drum at all - error 8 came on almost immediately.

Tips for troubleshooting problems yourself

Having established the error code and found out the reason for the blinking of the indicators, you can independently check and replace the board on the Indesit washing machine at home. To do this, you need to have a soldering iron, screwdrivers, a multimeter and a little experience in working with such tools.

First of all, you need to carefully disassemble the body of the machine. This work consists of the following stages:

  • the device is disconnected from the network;
  • remove the upper part of the body;
  • unscrew the screws holding the electronic board;
  • disconnect the wires;
  • change capacitors or install a new board.

Indesit washing machines are produced in two types: with vertical or horizontal loading. In the first case, the electronic board is located at the top of the device, in the second - at the bottom rear. Getting to it is not difficult, but you should always take into account the design features of a particular model.

The electronic board must be carefully examined from all sides. Most often, capacitors C16, C17, C20 fail. If the top of these elements is swollen, then the capacitor is clearly faulty and should be replaced.

In addition to external inspection, the board elements can be tested with a multimeter. Some capacitors dry out as a result of long-term use; upon visual inspection they cannot be distinguished from serviceable ones. Using a multimeter, you can more accurately determine where the circuit is broken and which of the elements requires replacement.

Now all that remains is to install the new capacitor and connect the wires correctly. The main thing is not to confuse the markings and choose the electrical element that matches the model of the machine. After the installation of the board is completed, the unit body is assembled and a trial run is carried out.

Flashing LEDs on the Indesit washing machine may be caused by user inattention or a malfunction. In any case, smart technology will tell you where to look for a breakdown. You just need to decipher the error code that corresponds to the combination of blinking indicators, and use the table to find out the reason for the malfunction of the unit.

The automatic washing machine in our house often literally wears out. Thanks to the abundance of modes and additional features, it makes our life easier. You can refresh your clothes after a working day, or you can load 6-7 kilograms of things at once. But this cannot go on forever, if all the indicators on the Indesit brand washing machine are blinking, this is a clear sign of problems.

How to determine the error code on cars without a display

Outdated Indesit models have a built-in EVO-I control system. However, they do not have a display to display information. But, nevertheless, they are able to report errors that have arisen in the system. They can be identified by blinking indicator lights. For example, flashing rapidly five times with a break of several seconds indicates error code F05.

In vehicles equipped with the EVO-II control system, the method for determining codes is slightly different. After all, each model has different functionality. And this makes it difficult to read errors. To understand the fault code, you need to understand what this or that indicator indicates.

The following types of indicators are distinguished:

  • timer – kn1;
  • super wash – kn2;
  • quick wash – kn3;
  • additional rinse – kn4;
  • spin – led4.

Now let's look at how to read the meaning of indicator signals.

Indicator readingsErrorDecoding
Blinking kn4F01There is a short circuit in the motor control triac.
Blinking kn3F02The machine's engine has failed. Possible causes of the problem: the drive belt is jammed; there is a short circuit or break in the network.
Kn3 and kn4 flashF03The circuit in the temperature sensor is shorted or broken.
Blinking kn2F04Problems with the level relay. The system cannot determine whether the tank is full or empty.
Kn2 and kn4 flashF05After the command to drain the water, the relay does not indicate that the tank is empty. Reasons: failure of the pressure switch; blockage in the drain system; failure of the drain pump.
Kn2 and kn3 flashF06There were errors on the button panel and the machine did not understand the command.
The indicators kn2, kn3 and kn4 are flashingF07The heating element does not work (does not heat). The problem may occur if the heating element is not in the water.
Blinking kn1F08The contacts on the heating element relay are stuck. Reasons: broken heating element or broken wires.
The indicators kn1 and kn4 are flashingF09There was a problem in the machine's memory.
The indicators kn1, kn3 and kn4 are flashingF11No electrical impulses are sent to the drain pump. Reason: broken wires.
No indicator lights upF16The error is typical only for models with vertical loading of laundry. Reason: drum jammed.
LED4 and kn4 are flashingF17There is no voltage in the door lock or it is not completely closed.

The most rare reasons why a car blinks

If Indesit does not turn on, then it is worth considering even rare causes that could lead to failure. You need to pay special attention to them, because many people ignore them, and, as a result, cannot figure out the machine on their own.

It is important to accurately determine the breakdown. Be sure to check the following points:

  1. Involuntary drainage of water, which leads to breakdown.

  2. Electric motor failure. This is a fairly serious breakdown, so you can’t do it without a repairman.

  3. Burnout of heating element.
  4. Drain pump malfunction.

Let us note once again that if the washing machine does not work, the indicators will definitely flash accordingly. That is why there is no need to guess, just look at the indicators.

It is important to note that the heating element can become covered with scale over the years. That is why its wear increases significantly. The electric motor can break down due to the fact that the condition of the brushes deteriorates significantly. Fur and hair could also become tangled, which is especially common in apartments where animals live. In this case, the control module may become less likely to leave its normal state. Burnt contacts can lead to this, and this situation is quite rare.

Be sure to follow the Indesit instructions when checking error codes. The most important thing is to accurately diagnose the breakdown, so that you can then fully carry out repair work. If the cause is not correctly identified, significant amounts of money may be required to eliminate the problem. It’s better to do everything right right away so that you don’t have to worry about the problem later.

Error codes indesit w 105 tx

The displayed fault codes for Indesit washing machines are presented in Table 1.

Table 1 - Errors, their names and possible causes

  1. Indication on the display of an error that has appeared
Decoding the information that appearsReasons for the malfunction
F 01Short circuit (short circuit) in the motor control circuit1) The triac responsible for: turning the electric motor on and off has failed; regulation of its speed. 2) Short circuit of contacts on the connector due to water ingress.
F 02Lack of feedback from the tachogenerator1) Break in the supply wire to the motor. 2) Broken motor stator winding. 3) Tachogenerator malfunction. 4) Lack of contact with the controller board.
F 03Temperature sensor is faultyNo change in water temperature. 1) The temperature sensor is faulty. 2) The heating element is faulty. 3) Lack of contact in the heating element relay.
F 04Double signal on the pressure switchThe controller receives two signals about a high water level, at which the drain valve opens, and about insufficient water, at which the water supply valve turns on. Malfunction of the sensor that monitors the water level in the tank.
F 05No empty tank signal1) Drain pump failure. 2) The drain line is clogged. 3) Malfunction of the sensor responsible for monitoring the water level in the tank.
F 06Mismatch when choosing a washing program1) The pre-dial code from the washing mode selection button does not match the controller parameter.
F 07Insufficient water level to turn on the heating element1) There is no signal from the pressure switch about filling the tank. 2) The heating element is faulty. 3) Contact sticking in the heating element.
F 08Working heating element while draining water1) Malfunction of the pressure switch. 2) Contact sticking in the heating element relay.
F 09Error in the operation of non-volatile memory installed on the “EEPRO M” controller board1) Failure of the PROM - a rewritable programmable storage device (non-volatile memory).
F 10No signals from the pressure switch1) Malfunction of the pressure switch. 2) Lack of contact with the controller board.
F 11There is no power to the drain pump1) Broken winding in the motor. 2) Malfunction inside the unit.
F 12No indication1) The display board is faulty. 2) Lack of contact between the controller board and the indication board.
F 13No signal from the clothes drying temperature sensor (only for machines equipped with this function)1) Sensor malfunction. 2) Lack of contact.
F 14No heating of the heating element in the clothes drying mode1) Malfunction of the heating element. 2) The power circuit is broken.
F 15The drying mode does not turn off1) Contact sticking in the heating element relay. 2) The control circuit is broken.
F 16Stopping the drum not in the upper position (for machines with vertical loading)The drum loading door must be at the top. 1) Lack of power. 2) Failure of the stop control system.
F 17Loading door is not closed1) No power to the door lock. 2) Damage to the lock mechanism.
F 18Internal controller error1) There is no connection between the controller board and the executive control board.

As can be seen from the table, for each error information there are several reasons for its occurrence. And as a result, the light warning shows the direction in which to start troubleshooting, which significantly saves the time of service workers and reduces the time the washing machine is under repair.

Troubleshooting and possible repairs

First of all, you should know that a failure situation is not always fatal. In most cases, the problem is only a slight slowdown of the electronics - just disconnect the machine from the current for 15-20 minutes, and then start it again for everything to work.

This action should always be the first in the process of troubleshooting.

If there is no result, it’s time to take on specific instructions. Each problem has a serial number after the letter marker F and a required repair. For convenience, various faults are divided into categories.

#1 - electric motor problems (F01, F02)

Outwardly, both positions look the same - the machine is inactive from the very beginning, washing does not start after pressing the start button.

On electronic models the indicator F01 or F02 , on electromechanical ones (without a monitor):

  • “Additional rinse” is on or “Spin” is flickering, at the same time “Lock” is active;
  • The “Quick Wash” button is active or the “Extra Rinse” button is blinking.

Or no indicator lights up except the lock icon.

If the value F01 appears on the display and after a reboot, you need to check:

  • voltage strength in the network (normally more than 200 V);
  • serviceability and integrity of the socket and cord.

If there is no result, you need to open the back panel of the equipment and inspect the engine - it is located under the tank - for wear on the windings, motor brushes, and the serviceability of the triac. If any of this is damaged, the engine will most likely have to be replaced, and how to do this is written in detail here.


This is what the electric motor of Indesit automatic machines looks like - its average cost is 4700-6000 rubles or $40-100, and the design of the element is compatible with Ariston analogues

Problem F02 relates, among other things, to the tachometer that counts revolutions. To solve this, you should carefully examine all the contacts involved in the motor-tachometer and board-tachometer connections. There should be no broken wiring or loose terminals.

Along the way, it is necessary to check the resistance of the tachogenerator - the operating indicator is 100 Ohms and higher. Otherwise, the unit is also subject to more qualified inspection and replacement.

#2 - sensor failure (F03, F04, F07, F13)

For all these breakdowns, the problem lies in special sensors. You need to act according to the error code that appears and the model of the washing machine.

On F03 is indicated by “Revolutions” and “Quick Wash” lighting together, or “Revolutions” and “Additional rinse” blinking. This means that the machine does not heat the water, so the system will not start from the very beginning.

To eliminate the violation, the following are checked:

  • rinsing function - turn on, turn off, start washing;
  • contact elements of the temperature sensor - a device 20-30 mm inside the system tank;
  • thermostat resistance, which should be 20 kOhm or higher.

If everything is intact or turned out to be broken, but was corrected, and the washing still does not start, the thermostat must be replaced after checking it and the entire control board by the master.

Code F04 without a display is manifested by the frozen burning of “Super Wash” or the dynamic flashing of “Soaking”.

The system tells the user that water is not filling or not filling enough, even if filling occurs. The source of the breakdown is the water level meter (pressure switch).

You can recognize the pressure switch by its characteristic plastic case and volumetric size; you need to look for it in the upper part of the system. It cannot be repaired due to the monolithic shell - only replacement will save it

What needs to be done to correct the inconsistency:

  • check the presence of water in the water supply;
  • measure the pressure - for the machine to work correctly you need at least 1 atm;
  • inspect the supply tubes, hoses, filters (if there are any blockages there) and clean them of debris;
  • check the water supply valve for mobility;
  • Replace a failed pressure switch based on the results of an inspection by a specialist.

It may happen that the culprit is a short circuit in the control module, which can also be determined by a visiting technician.

You can read even more about why the washing machine does not fill with water in this article.

When the equipment reports a failure under the sign F07 , you need to act in exactly the same way as in the case of F04 . The code is simply one of the types of pressure switch failures.

The only difference is how the machine reports this: “Super Wash”, “Quick Wash” and “Revolution” are lit at once, or “Soaking” with “Revolution” and “Re-Rinse” continuously flickers.

Coding F13 is expressed by the “Delay start” and “Super wash” indicators (they freeze and light up together) or the turn indicator and the rinsing function. The basis of the breakdown is that drying is not carried out.

The drying heating sensor does not look like a general temperature sensor: the first resembles a tablet when viewed, the second - a long capsule. The standard motor thermostat is oblong and can be easily replaced

In most cases, a simple reboot will save you, since the temperature sensor is frozen. But if no changes have occurred, the drying thermometer can only be checked for insulation; in other cases, it must be replaced.

#3 - incorrect drain and fill (F05, F10, F11, H2O)

The group of problems associated with the operation of the drain pump has similar symptoms to the manifestations of the previous series of errors.

The most striking symptoms:

  • the washing machine pumped water and stopped despite being filled;
  • the system notifies about an empty tank;
  • The rinse and spin function does not work;
  • no water is pumped out.

The failure of the drain pump design is to blame.

The first step is to check the drain filter and the permeability of the sewer. The cleaning unit is located on all models on the side where the water supply hose inlet is located. A clogged drain filter, especially in the case of F11 , almost always means the pump is burnt out; the latter will have to be replaced.

A clogged drain needs to be cleaned, making sure at the same time that the tap of the water supply system is not accidentally turned off or the water is not turned off at all.

Other causes of failure are malfunction of the water supply valve, damage to the pressure switch, damage to the wiring of the pump-control board assembly, and failure of the board itself.

You can correct the wiring, make adjustments, or reinstall the pump or valve manually, but repairs to the control module and level sensor must be carried out by a specialist.

You can only get to the SMA Indesit drain pump through the bottom of the equipment from the front, this is what distinguishes it from analogues from other manufacturers

To find out without a monitor that it is the drainage system that has broken down, you need to check the indicators:

  • F05 - “Super wash”, “Rinse again” are turned on at the same time, or “Spin”, “Soak” are blinking;
  • F10 - “Quick Wash” and “Delayed Start” remain lit, or “Revolutions” and “Additional Rinse” blink, while “Door Block” blinks at high speed;
  • F11 - continuous lighting of “Delay”, “Quick wash”, “Re-rinse”, the second type - “Spin”, “Revolution”, “Additional rinse” flash simultaneously.

H2O that is different from others . From the outside it seems that this is the letter H and the number 20. In fact, the usual formula of water is used here as an indication that the breakdown is connected specifically with the “water” sphere.

The hint can appear simultaneously with another code, as an addition, and the same methods as described for F05, 10 and 11 are suitable for eliminating its consequences.

#4 - electronics failure (F06, F09, F12, F18)

If the display shows F06, F09, F12 or F18, the “brain” of the machine – the motherboard – has broken down. The washing machine does not react in any way to the given commands, and no matter how much you press the buttons, it only issues a certain code (when there is a screen).

Talking LEDs allow you to understand if the control module is damaged:

  • F06 – “Super wash” - “Quick wash” are active or “Additional rinse” - “Soak” are blinking, plus “Increased contamination” - “Iron” are on, “Lock” is blinking quickly;
  • F09 – “Delayed wash” - “Re-rinse” are active or “Revolutions” - “Spin” are blinking;
  • F12 – “Delayed wash” - “Super wash” are active or the speed indicator is flashing;
  • F18 – “Spin” - “Quick wash” are active or “Delay” - “Extra rinse” are blinking.

The only way to correct this situation on your own is to reboot the system. You should unplug everything from the network and leave it for half an hour, then plug it back in.

Checking the integrity of the electrical wiring will also help. All other methods require disassembly, repair and reinstallation of the control center.


The washing machine's motherboard is a sensitive electronic mechanism responsible for all work. That’s why the place where it is located (the area of ​​the “Start” button) should never be filled with water.

Position F06 is characterized by failure of the “Start” button, failure of the triac, or break in the wiring.

The infrequent error code F09 signals the need to replace the control contacts of the washing machine, reset the board settings, or reflash the entire module.

F12 marking indicates a breakdown in communication between the board and the indicator contacts.

Worst of all, when error F18 , the only way to correct it is to completely replace the entire system unit.

#5 - faulty heating element (F08, F14, F15)

The operation of a heating element - a tubular electric heater - allows an automatic washing machine to heat water and dry clothes. In Indesit models it is located in the rear.

Error F08 is one of the most common during the washing process. This means that the heating element is not functioning.

Among other signs of a malfunction: the laundry after the procedure turns out to be as dirty as before (for old prototypes), the laundry takes too long to wash, the process does not stop on its own, the laundry is still wet after drying ( F14 ), drying does not start at all after washing ( F15) .

If there is no monitor for different codes, the following lights up and freezes at the same time:

  • F08 – “Quick wash” or “Power”;
  • F14 – “Delayed start”, “Super mode”, “High speed mode”;
  • F15 – “Delayed start”, “Super mode”, “High speed mode”, “Additional rinse”.

What you need to do to fix it:

  • inspect the water level meter for damage;
  • find out if there are any blockages in the drainage system;
  • check the wiring and contacts between the heating element and the module for insulation and integrity, do the same for the heating element-thermostat connection;
  • test the control module.

Based on the inspection results, you will have to either replace the heating element, or reinstall one of the sensors (level, temperature), or install a completely new control unit.

The most famous reason for the breakdown of washing equipment is the same heating element. It is about its safety that so much is said in advertising when offering water softeners.

The need to replace electric heating tubes arises for owners most often, but this is quite easy to do without spending money on a technician. You will need a flat and shaped screwdriver and a socket wrench.

Work order:

  • Step 1 - completely separate the washing machine from all communications.
  • Step 2 : Carefully turn the back wall towards you and remove the outer panel.
  • Step 3 – under the tank you can see the contacts of the heater, which goes inside, disconnect their terminals.

Next, we use a wrench with a head - with its help, the central bolt on the contact panel is unscrewed. After this, the heating element should be alternately picked up from several sides with a flat screwdriver and pulled towards you; the faulty element will be in your hands.

By easily reinstalling a tubular electric heater yourself, you can save a lot of money, since replacing this element by specialists costs from 1000 rubles

All that remains is to remove the thermometer from it and attach it in the same place to the new electric heater. Next, the heating element is installed to replace the old one in the reverse order, but first it is better to clean the seat from accumulated dirt.

#6 - incorrect drum position (F16)

This type of error appears only on washing machines with a vertical loading method. In this case, the washing procedure does not begin after pressing “Start” or suddenly stops in the middle of the cycle. The drum has fallen silent, the “Lock” light is blinking intensely.


The vertical loading drum should be secured with a special button before you start washing, otherwise the hatch will open when twisted and break the machine.

Necessary:

  • turn off the system, open the lid, move the drum with your hand - often it is jammed by a foreign object, for example, a torn button or hard parts of underwear - remove the obstacle, start the unit back;
  • inspect the drum hatch to see if it has accidentally swung open (due to damage) and is blocking movement;
  • the locking function - UBL is responsible for it - the hatch block device, replace if damaged;
  • the control module for serviceability and replace the faulty one.

A reverse failure may occur when the drum does not stop. The situation will be solved by disconnecting the washing machine from the network for 20 minutes.

#7 - hatch sealing does not work (F17)

A problem identical to the previous number in terms of symptoms is caused by the fact that the door could not be locked before starting.

On models without information screens, it appears simultaneously by the indication of the “Spin” and “Re-rinse” (“Power”) buttons or a combination of “Push-ups” and “Delayed start”.

Perhaps the lid just needs to be closed more tightly. If this does not work, check for foreign objects or breaks between the inlet hole and the hatch valve or between the hatch and the rubber lip. The door also does not close when the drum is overloaded.

Another option is that the UBL has deteriorated or the control center has shorted out. Replacing them will solve the problem. The third option is low voltage. This is often observed in individual houses, but it is not uncommon in apartments.

If the power supply does not reach 220 V, an electrical appliance of this size will not work.


The rubber seal between the body and the tub door can accumulate laundry waste or foreign objects that have fallen into the drum. This may cause the lock to fail to lock, so it is better to periodically clean the cuff cavities

The manufacturer Indesit received 19 signals about defects in the operation of its equipment.

If a situation arises that does not fit any of the described errors, you will have to contact a reliable service center or official representative office of the company individually.

We also recommend reading our other material, where we described in detail the popular malfunctions of Indesit washing machines and how to eliminate them. For more details, follow the link.

Errors related to the ECU board

The memory chips located on the control unit board contain all service algorithms and washing programs. If a failure occurs, the memory must be removed from the ECU (unsoldered or removed from the microcircuit connectors) and reprogrammed with a special device - a programmer.

If the connection between the display module and the ECU board is broken, this malfunction of the Indesit washing machine manifests itself in the lack of response to buttons and the inability to execute programs. If after disconnecting from the 220 V network and rebooting the ACM nothing has changed, check the condition of the connectors and the reliability of the switching connections. The most likely fault is in the display module board or ECU.

Control and display module in some Indesit CM models

Common error manifestation

The car breaks down when you least expect it. The user, out of habit, places the laundry in the drum and starts the wash cycle. However, contrary to normal operation:

  • the washing does not start, instead, the lights on the control panel blink;
  • the process starts, but after a certain time the machine freezes, stops functioning, and the LEDs on the panel light up or blink.

The washing cycle can be interrupted at any stage: soaking, rinsing, spinning, draining. A lit indication coupled with the washing machine stopping operation indicates a malfunction of the equipment. To find a solution to the problem, you need to understand what kind of failure the device is reporting. Deciphering blinking indicators is not as difficult as it might seem at first glance. In this article we will try to describe all possible fault codes and the corresponding indication. To decrypt errors, you should:

  • find out the type of your Indesit washing machine by the first letters in the model name;
  • understand which combination of light bulbs is lit;
  • Based on the description presented in the article, identify the alphanumeric designation of the error code indicated by the self-diagnosis system of the machine.

You can often find out the cause of the breakdown and repair the washing machine yourself. However, if you find it difficult to decipher the code by the blinking lights, you can invite a qualified technician to help identify the problem and fix it.

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]