Hansa dishwasher operating instructions

Installation and connection

The Hans dishwasher is quite simple to use. By following simple installation rules and recommendations, you can ensure long-term performance.

Basic rules for installing a dishwasher:

• Upon receipt and delivery, check the integrity.
• Before turning it on, be sure to ground the outlet; call a technician to do this.
• Check the power supply readings.
• During installation, turn off the power and water supply (close the valve).

An extension cord cannot be used; an original plug is required to connect to the outlet.

There are a number of the most important recommendations from the manufacturer that ensure the longevity of the machine:

• Before use, carefully read the built-in dishwasher manual and safety precautions.
• Restrict access to the car to people with mental and physical disabilities and children.
• Place sharp instruments horizontally or vertically with the sharp end down to prevent injury.
• To avoid damage, do not place heavy objects on the machine.

To eliminate breakdowns, it is better to contact professionals at certified centers.

Device

Each model offered by the Hansa brand has its own characteristics, but basically the PMM scheme is as follows:

• control panel equipped with a display;
• baskets for dishes (upper, lower);
• shelf for cups;
• instrument compartment;
• dispensers for detergent, rinse aid, salt;
• filters and sprayers inside the workspace;
• drain hose;
• inner tube;
• water supply hose.

How to use

The basic rules of use are as follows:

• The upper basket is designed to accommodate lightly soiled tableware made of fragile glass and porcelain. It is best to place glasses and cups here, and place cutlery horizontally between them.
• Plates and cups must be placed in such a way that they do not touch the filters and sprinklers.
• The lower basket is intended for very dirty plates, cups, for example, baking trays, bowls, salad bowls. The manufacturer recommends placing the plates upside down so that the entire surface gets water.
• Special trays (available in some models) are designed specifically to accommodate spoons and forks.

Indicators

Each Hans car has the following panel icons:

• Power supply – lights up when the equipment is plugged in.
• Half load indicator.
• Level indicator for cleaning and polishing solution (if it is on, you need to add more).
• Salt presence/absence sensor (if it lights up, you need to add salt).

Buttons

The following buttons are located on the PMM body:

• “On/Off” to stop or supply power;
• program selection button, cleaning cycle;
• half load button if less than 7 sets of dishes have accumulated;
• reboot and start.

Programs

As standard, Hansa appliances have the following dish cleaning modes:

• Standard sink for everyday use, used for dishes without dried dirt.
• Intensive mode, which makes it possible to clean even old dirt from dishes.
• Delicate mode – used for glasses and glasses without heavy soiling.
• The “hour” cycle is designed for lightly soiled dishes; there is no drying of the dishes.
• Pre-soaking – required for heavily soiled dishes, used before the main wash.
• The “eco-cleaning” mode is intended for cutlery made of crystal and porcelain to provide delicate washing and prevent chips and cracks.

It is necessary to turn on the machine only after all compartments have been loaded.

How to turn it on

Hansa PMMs are quite easy to use; in order to turn on the dishwasher, you need to:

1. Plug in the power cord and check if the water supply valve is open.
2. Add dishes, cleaning agent and close the door.
3. Select a program, mode and press the appropriate button.
4. Click "Start".

First start

The first start of the washing mode must be carried out according to the following recommendations:

1. Load the dishes into the working plane of the device and, if possible, move them towards the rear wall.
2. Add the tablet, powder and salt, pour in the rinse aid.
3. After downloading and selecting the “Start” button, the machine will start working after 10 minutes.

If you urgently need to stop the machine and change the cleaning mode, you can do this before the device begins to flush detergent from the specialized compartments. To do this, you can open the door, and then the Hansa appliance will automatically stop operation. After this, switch the washing mode, close the door again, wait 10 minutes - the machine will start working.

How to drain the water

If the filter is clogged and water does not flow out of the machine completely, you must drain the water from the Hansa dishwasher yourself:

1. Select the manual water drainage program on the control panel.
2. Monitor the process.
3. Disconnect the equipment.
4. Close the water supply valve.
5. Place rags under the device to absorb any remaining water from the work area.
6. Unscrew the filter cover at the bottom of the housing and the salt compartment cover.
7. Tilt the machine on one side to allow any remaining water to drain.
8. Wash the inside of the device dry, leave the door open for 10-15 minutes so that it dries well inside to prevent an unpleasant, musty smell.

If the PMM is used only in the summer in an unheated room, then leaving it with water for the winter is dangerous. When water freezes inside, it ruptures the plastic pipes, requiring expensive repairs.

Replenishing salt in the dishwasher

Page 9

• Image
• Text

7

Pour salt into the container using the included watering can (Fig. 2).

Add enough salt to fill the container. Capacity

is approximately 1 kg of salt.

Tighten the plug thoroughly.

Start the washing program immediately after filling the salt container. Washing program

will prevent damage to the machine due to leakage of salt solution.

If your dishwasher is equipped with a low salt warning light, then

filling the machine with salt, the light usually goes out after a few days (water in the container

must reach a certain concentration)

Attention

Each time after replenishing the amount of regeneration salt, the program should be started

sinks

Replenishing salt in the dishwasher

Attention

To soften water, use only dishwasher salt.

The manufacturer is not responsible for damage resulting from the use of

inappropriate type of salt.

Do not use coarse salt as it will be late in reaching its proper level.

concentrations in the water, which can cause the low salt light to stay on.

Small grains or salt in powder dissolve much more easily.

Never use kitchen or table salt. These types of salt do not dissolve easily

in the water and will damage the softening system.

Remove the lower rack from the dishwasher.

Unscrew the cap of the salt container by rotating it against

clockwise (Fig. 1).

When filling for the first time, pour 0.5 liters of water into the salt container.

Problems and solutions

Due to improper connection and operation, users often encounter problems and breakdowns.

Filling system problems

Such problems are always associated with blockages, so you should know how to eliminate them:

1. Turn the water supply valve to the “Off” position and disconnect the machine from the mains.
2. Disconnect the water supply hose from the housing and check for plugs and debris. Do the same steps with the filter and mesh.
3. To remove stagnant debris, place the filter in water with citric acid.
4. Carry out valve diagnostics by ringing the coils; if necessary, replace worn elements.

Checking the circulation pump

It is better to check the circulation pump when there is no water injection and it does not enter the working space of the machine, because due to the circulation pump, water flows into the rocker arms and the dishwashing function is activated. Diagnostics and repairs will be necessary if you hear knocking, buzzing, or noise.

For repair you need:

• Provide normal access to the bottom of the workspace and remove the bottom panel of the housing.
• Remove the fasteners and drain pump by turning the pump clockwise.
• Remove the special clamps with an adjustable wrench and disconnect the pump, replace the non-working equipment.
• Transfer the clamps and mounting bolt from the old pump to the new element and perform the same assembly, only in reverse order.

Installation and connection

The Hans dishwasher is quite simple to use. By following simple installation rules and recommendations, you can ensure long-term performance.

Basic rules for installing a dishwasher:

• Upon receipt and delivery, check the integrity.
• Before turning it on, be sure to ground the outlet; call a technician to do this.
• Check the power supply readings.
• During installation, turn off the power and water supply (close the valve).

An extension cord cannot be used; an original plug is required to connect to the outlet.

There are a number of the most important recommendations from the manufacturer that ensure the longevity of the machine:

• Before use, carefully read the built-in dishwasher manual and safety precautions.
• Restrict access to the car to people with mental and physical disabilities and children.
• Place sharp instruments horizontally or vertically with the sharp end down to prevent injury.
• To avoid damage, do not place heavy objects on the machine.

To eliminate breakdowns, it is better to contact professionals at certified centers.

Device

Each model offered by the Hansa brand has its own characteristics, but basically the PMM scheme is as follows:

• control panel equipped with a display;
• baskets for dishes (upper, lower);
• shelf for cups;
• instrument compartment;
• dispensers for detergent, rinse aid, salt;
• filters and sprayers inside the workspace;
• drain hose;
• inner tube;
• water supply hose.

How to use

The basic rules of use are as follows:

• The upper basket is designed to accommodate lightly soiled tableware made of fragile glass and porcelain. It is best to place glasses and cups here, and place cutlery horizontally between them.
• Plates and cups must be placed in such a way that they do not touch the filters and sprinklers.
• The lower basket is intended for very dirty plates, cups, for example, baking trays, bowls, salad bowls. The manufacturer recommends placing the plates upside down so that the entire surface gets water.
• Special trays (available in some models) are designed specifically to accommodate spoons and forks.

Indicators

Each Hans car has the following panel icons:

• Power supply – lights up when the equipment is plugged in.
• Half load indicator.
• Level indicator for cleaning and polishing solution (if it is on, you need to add more).
• Salt presence/absence sensor (if it lights up, you need to add salt).

Buttons

The following buttons are located on the PMM body:

• “On/Off” to stop or supply power;
• program selection button, cleaning cycle;
• half load button if less than 7 sets of dishes have accumulated;
• reboot and start.

Programs

As standard, Hansa appliances have the following dish cleaning modes:

• Standard sink for everyday use, used for dishes without dried dirt.
• Intensive mode, which makes it possible to clean even old dirt from dishes.
• Delicate mode – used for glasses and glasses without heavy soiling.
• The “hour” cycle is designed for lightly soiled dishes; there is no drying of the dishes.
• Pre-soaking – required for heavily soiled dishes, used before the main wash.
• The “eco-cleaning” mode is intended for cutlery made of crystal and porcelain to provide delicate washing and prevent chips and cracks.

It is necessary to turn on the machine only after all compartments have been loaded.

How to turn it on

Hansa PMMs are quite easy to use; in order to turn on the dishwasher, you need to:

1. Plug in the power cord and check if the water supply valve is open.
2. Add dishes, cleaning agent and close the door.
3. Select a program, mode and press the appropriate button.
4. Click "Start".

First start

The first start of the washing mode must be carried out according to the following recommendations:

1. Load the dishes into the working plane of the device and, if possible, move them towards the rear wall.
2. Add the tablet, powder and salt, pour in the rinse aid.
3. After downloading and selecting the “Start” button, the machine will start working after 10 minutes.

If you urgently need to stop the machine and change the cleaning mode, you can do this before the device begins to flush detergent from the specialized compartments. To do this, you can open the door, and then the Hansa appliance will automatically stop operation. After this, switch the washing mode, close the door again, wait 10 minutes - the machine will start working.

How to drain the water

If the filter is clogged and water does not flow out of the machine completely, you must drain the water from the Hansa dishwasher yourself:

1. Select the manual water drainage program on the control panel.
2. Monitor the process.
3. Disconnect the equipment.
4. Close the water supply valve.
5. Place rags under the device to absorb any remaining water from the work area.
6. Unscrew the filter cover at the bottom of the housing and the salt compartment cover.
7. Tilt the machine on one side to allow any remaining water to drain.
8. Wash the inside of the device dry, leave the door open for 10-15 minutes so that it dries well inside to prevent an unpleasant, musty smell.

If the PMM is used only in the summer in an unheated room, then leaving it with water for the winter is dangerous. When water freezes inside, it ruptures the plastic pipes, requiring expensive repairs.

Problems and solutions

Due to improper connection and operation, users often encounter problems and breakdowns.

Filling system problems

Such problems are always associated with blockages, so you should know how to eliminate them:

1. Turn the water supply valve to the “Off” position and disconnect the machine from the mains.
2. Disconnect the water supply hose from the housing and check for plugs and debris. Do the same steps with the filter and mesh.
3. To remove stagnant debris, place the filter in water with citric acid.
4. Carry out valve diagnostics by ringing the coils; if necessary, replace worn elements.

Checking the circulation pump

It is better to check the circulation pump when there is no water injection and it does not enter the working space of the machine, because due to the circulation pump, water flows into the rocker arms and the dishwashing function is activated. Diagnostics and repairs will be necessary if you hear knocking, buzzing, or noise.

For repair you need:

• Provide normal access to the bottom of the workspace and remove the bottom panel of the housing.
• Remove the fasteners and drain pump by turning the pump clockwise.
• Remove the special clamps with an adjustable wrench and disconnect the pump, replace the non-working equipment.
• Transfer the clamps and mounting bolt from the old pump to the new element and perform the same assembly, only in reverse order.

Drain system malfunctions

If, after washing dishes, the water does not completely leave the workspace and accumulates below, it means that there is a problem with the drainage system. Often this is due to stuck and accumulated debris, to fix the problem you need to do the following:

• Remove all plates and glasses from the machine and pull the lower rocker towards you, carefully unscrew the upper rocker.
• Check sprinklers for debris. If necessary, clean the injectors using a toothpick.
• The drain filter and the metal mesh at the bottom of the working area should also be inspected and cleaned.
• If glasses or plates were chipped during the washing process, perhaps a splinter blocked the pump; Wearing gloves, it is necessary to carry out diagnostics.

Replacing the level sensor

In dishwashing equipment, the level sensor is called a pereostat; its function is to monitor the water level in the tank. Failure of this element may consist of physical wear, blockage, or malfunction of the electronic part.

Before a complete replacement, you need to check the element for blockages. To do this, you need to unscrew 2 screws from the bottom of the machine, the mounting clamp, and blow out the tube. The electronic part can be diagnosed using a multimeter.

Heating element diagnostics

The basis of the heating system is a flow-through heater, which is necessary to increase the temperature of the water when cleaning dishes. Its breakdown may be due to the inoperability of the heating element located under the bottom of the Hansa dishwasher. It is better to entrust the installation of the heating element to a specialist; for self-repair, the following is required:

1. Disconnect the heating element with the pump.
2. Unscrew the pump fasteners by turning them clockwise and remove the rubber seal.
3. Remove all tubes and pipes, replace the non-functioning part and reassemble everything in the reverse order.

Leak

To eliminate leaks, it is necessary to identify the exact cause and location; for this, the following occurs:

• Carefully inspect the inside and outside of the dishwasher.
• Check the quality of door closure and the reliability of the door seals; if necessary, replace them.
• Inspect the rubber seals on the drain pump; their wear can also lead to leakage. In this case, it will be necessary to replace the seal or the pump completely.
• Conduct diagnostics of the hose at the inlet and outlet, if necessary, tighten the tightening elements or replace the hose.

Hansa brand PMMs are reliable, convenient and functional; for simple and long-term use, each model comes with detailed and understandable instructions.

Share on social media networks:

When choosing household appliances for the home, every housewife strives to choose the most reliable and easy-to-use and maintain unit. Especially when it is a dishwasher, which you will have to use every day, or even several times a day. The Hans dishwasher, the instructions for which are presented in several languages ​​in a form that any user can understand, is German quality combined with a rich history and constant development of the brand. Let's talk in more detail about the various models of this German brand.

Basic moments

How to turn on the car? Any instructions for Hansa household appliances are quite detailed and contain about 40 pages of text, diagrams, tables and photos, which are convenient to use both when connecting the device and installing it, and during its direct operation, where you can also see how the machine turns on.

On the first pages, the manufacturer writes a greeting and gratitude for choosing the brand, as well as a recommendation to carefully read the instructions for a specific model before using it.

Instruction sections:

• symbols used in the instructions and their interpretation;
• safety precautions for handling a Hans dishwasher;
• installation instructions;
• description of the main parts of the machine;
• recommendations for preparation for launch;
• description and selection of washing programs;
• cleaning and care tips;
• possible errors and ways to eliminate them;
• device data sheet.

Any Hans dishwasher is equipped with similar information. The instructions are also supplemented with practical advice from the manufacturer.

Important! You will find similar recommendations in the instructions for any equipment from different manufacturers. If you haven’t bought one yet, but are just planning to get a dishwasher, perhaps our reviews of the best models in the following categories will help you:

Let's look at the most important points in more detail.

Dear Customers, Before plugging in the cookware cord...

Page 2

• Image
• Text

Dear customers,

Before you plug the dishwasher into an electrical outlet and

turn on the device, be sure to read the entire instruction manual

operation and installation. The instructions it contains will help reduce

risk of personal injury and damage to the device.

Machine documentation should be kept in a safe place for correct

operation and seeking help if necessary.

These operating instructions have been prepared for

devices and the individual features described herein may

do not touch your dishwasher.

Safety precautions

In this section, the manufacturer gives valuable instructions, following which you will be able to use the device correctly and definitely not harm yourself:

1. Check the packaging and integrity of the machine upon receipt. If you have any doubts about the integrity of the device, do not use it, but contact the seller for clarification.
2. Before connecting the device to the network, the outlet must be grounded. Doing this yourself is strictly prohibited, so you will have to contact a specialist.
3. Before turning on, check the electrical readings with the readings required for the operation of the Hans dishwasher.
4. During installation or repair, it is necessary to turn off the power and water supply to the device.
5. The manufacturer does not recommend using a connection via an extension cord, and also requests that only the original plug be used to plug into the network. The socket and plug must be quickly and easily accessible.
6. The use of a Hans dishwasher by persons who have not studied safety precautions, or by people with physical or mental disabilities is prohibited if the danger of using the device is high for them.
7. Separately, the instructions for the Hans dishwasher highlight the use of the device by children. Children over 8 years old are allowed to wash dishes in it, provided they have undergone instruction and understand the dangers that can occur if handled incorrectly. Children under three years of age are not allowed near the device. It is forbidden to play with the machine, drink water from the device, and detergents must be stored out of the reach of children.
8. During use, remember that the water may be heated, so there is a high risk of getting burned when opening the door while running the program.
9. To avoid injury from sharp objects, they are placed horizontally in the upper compartment or point down in the cutlery compartment.
10. It is prohibited to use a Hansa dishwasher for purposes other than its intended purpose - washing dishes.
11. Solvents must not be used in the device due to the risk of explosion.
12. Do not sit down, stand up or place heavy objects on the door of the device - the machine may tip over.
13. If repairs are necessary, you should contact a specialist.

These are the manufacturer’s main recommendations for safe handling of equipment. You can always find out more about the requirements and recommendations in the instructions for your model or use our article, which describes in detail the installation and connection processes of the dishwasher.

Proper care of your PMM

To avoid damage, use PMM only for dishes that can be washed in it. Do not load wooden or pewter items; not all dishwashers are suitable for washing plastic items. Don't forget to take care of the device. Wipe the doors, clean the filter. Of course, there are models with self-cleaning, but this also requires periodic supervision. The door seal should also be cleaned with a special product or a melamine sponge to prevent mold from forming or drying out.

Device structure

The design of dishwashers is determined by the manufacturer and depends on the specific model; it can also be built-in. In general, the device looks like this:

• drain hose and water supply hose fitting;
• filters and sprayers;
• inner pipe;
• dispensers for salt and detergents;
• shelf for cutlery;
• shelf for cups;
• lower and upper baskets;
• control panel with display.

Important! Please note that some parts may not be available depending on the model or that the Hans Dishwasher may require additions. Always check the instructions for details.

Next, we’ll look at how to properly place dishes in the dishwasher.

Program selection

Different models of Hans dishwashers have their own characteristics. We list the main functions that are found in almost all devices:

• Pre-wash or pre-soak - used when you need to soak stuck or burnt-on food residues.
• High-intensity washing allows you to remove the most stubborn stains at temperatures of +65 - +70°C.
• Standard sink - for cleaning dishes from medium to heavy stains.
• Eco-wash is used for all degrees of soiling, except heavy. It features reduced consumption of electrical energy, water and detergent.
• The delicate wash is suitable for fragile items: glass, porcelain, crystal at a temperature of +45°C.
• Quick wash is half as long as the standard cycle and takes place at +55°C.

Loading the machine

You can highlight the basic rules for loading products into the device, the observance of which will allow you to use it most effectively.

Upper basket

In this basket you can place fragile glassware, porcelain, as well as tea pairs, cups and glasses. You can also place cutlery between them. The dishes must be laid out so that they are not touched by the spray nozzles when the device is operating.

Important! It should be remembered that items placed in the upper basket should be lightly soiled.

Lower basket

More soiled items and deep dishes can be placed in this basket. For example: bowls, pans, baking sheets. As in the case of the top one, it is necessary to arrange objects in such a way that they do not touch them when the device is operating. And so that the water drains, it is better to place the products upside down.

Cutlery tray

If the machine is equipped with a special compartment, then cutlery should be placed in it. It is important to fold them with their handles up, place the longest utensils in the middle, and also make sure that they do not cling to each other.

You can find out more about the loading rules in the instructions for the Hansa dishwasher of your particular model. Our article on how to use a dishwasher correctly will also help you.

Let's take a closer look at the design of Hansa machines using the example of several models.

Unpacking, kit

HANSA ZIM 626EH is packaged as standard for a dishwasher - installed on a tray, covered with a thick cardboard box on top. Wherever necessary, additional seals are laid.

Since the machine is built-in, all the necessary installation kit is included.

Equipment:

• Dishwasher HANSA ZIM 626EH
• Mounting kit
• Funnel for loading salt
• User manual, installation diagram, stickers

The set is quite laconic: there is only what you cannot do without. However, there are no test strips for determining water hardness, nor a starter kit of detergents.

Hansa ZWM 476 SEH

This is a full-size dishwasher with six different programs and five temperature settings, as well as Aquastop leak protection. The device can hold up to 10 place settings. The device control type is electronic.

Let's look at the main indicators and buttons on the control panel.

Indicators:

1. Power supply. When the indicator is on, the machine is connected to the network.
2. Program indicators. Indicate the selected cycle.
3. ½ load. When the indicator is on, it means that the half load function is active.
4. Lack of dish polish solution - if it burns, you need to add product to the compartment.
5. Lack of salt - when the indicator is lit, add salt to the appropriate compartment.

Buttons:

1. Turn on/off the device. By pressing this button, electricity flows into the device or stops flowing.
2. Selecting a program. Using this button you can select the required washing cycle.
3. ½ Load Enables the half load function. It can be used if you have accumulated less than 7 sets of dishes.
4. Start/Reboot. Used to restart, select a cycle or reboot the device.

Next, let's talk about the wash cycles available for this model.

Programs

The model has six modes:

1. Daily wash - designed for washing dishes without dried stains.
2. Intensive mode - allows you to wash away heavy stains, but without dried food particles.
3. Delicate cycle - will help wash glass or porcelain dishes, but without heavy soiling.
4. Eco 50 - allows you to wash more dirty glass or porcelain items.
5. One-hour cycle - designed for dishes with light soiling, without additional drying of the items.
6. Soaking mode - will help get rid of dried dirt before the main wash.

Important! Switching on is possible only after filling all the necessary containers with the product and loading it with dishes. In order not to spend a lot of money on purchasing consumables, but also not to lose on the quality of detergents, use our thematic selections:

First start

In order to start the washing cycle, you must perform a certain procedure:

1. Load dirty dishes into the device and move them to the back wall.
2. Add detergent, salt and rinse aid to the required compartments.
3. Connect the device to the network and open the water supply.
4. Use the program selection button to set the desired mode.
5. Press the start button to start the device.

The dishwasher will start operating approximately 10 seconds after starting.

Important! You can also change the program, but before the machine starts washing detergent out of the trays. To do this you need to open the door. The machine will automatically pause. Next, you can select the desired program and close the door. The device will resume operation in the new mode in approximately 10 seconds.

Hansa ZIM 414 H

This built-in dishwasher can hold up to 9 standard place settings. The model has 4 programs and is protected from leaks.

Control Panel

Key control panel elements include:

1. Washing program selection buttons.
2. Program indicators.
3. Indicators of lack of salt and rinse aid.
4. Device on/off button and corresponding indicator.

Modes

The model is equipped with four programs:

1. Intensive mode - allows you to wash very dirty dishes with dried particles. The cycle lasts 130 minutes.
2. Short wash is a half-hour cycle that can handle lightly soiled dishes without starch.
3. The ECO program will help wash lightly soiled dishes, but will cope with starch. The cycle duration is 160 minutes.
4. 3 in 1 mode - a cycle suitable for daily washing of dishes with dried stains lasting 160 minutes.

Important! All programs additionally dry dishes, with the exception of the short cycle.

The first start-up sequence is similar to the ZIM 414 H model.

Distinctive features

When you decide to purchase a Hans dishwasher, you should learn about the features and advantages of the equipment.

These include:

• Stylish, modern design of each model . Any Hans device can fit harmoniously into the kitchen interior;
• saving . Thanks to the Hansa dishwasher you can significantly reduce electricity, water and your time, which you can devote to more important matters;
• effective cleaning . The machine can easily cope with any degree of contamination, perfectly washing each product.

Hansa ZIM 636 EH

This built-in dishwasher can hold up to 14 place settings. It has 6 programs, electronic control, and is also equipped with a child lock and leak protection. An additional pleasant bonus is the delay start function.

Control

The control panel consists of buttons and indicators. There are several more of them here than in the previously discussed models:

1. On/off button and corresponding indicator.
2. Warning indicator that the salt or rinse aid is running low.
3. Indicator and delay start button. The delay start time can be set to 3, 6 or 9 hours.
4. Indicator and ½ loading button. The button allows you to select a given program and the corresponding lamp lights up.
5. Indicator of the selected mode.

Programs:

1. Intensive - suitable even for dried stains. Cycle time is 140 minutes.
2. Normal wash is a mode for washing every day. The utensils may have food residues, but not dry ones. The cycle lasts 160 minutes.
3. Eco mode - allows you to wash medium-sized stains and is also suitable for daily washing. Its duration is 170 minutes.
4. Glassware - allows you to wash lightly soiled dishes and glassware. The duration of the regime is two hours.
5. Hour mode - suitable for dishes with light stains that do not require perfect drying. Duration: 60 minutes.
6. Quick wash - allows you to wash lightly soiled dishes in half an hour, without using a dryer.

Important! The end of the cycle is accompanied by a sound signal.

Specifications