Extension of trousers at the waist, hips and sides independently

Trousers are a universal item in men's and women's wardrobes. For the stronger sex, they have become the main item of clothing. But women have long appreciated and enjoy all the advantages and benefits of trousers. However, this familiar product sometimes unexpectedly fails. They match our figure too closely. And therefore they immediately point out that the owner of the pants forgot about a balanced diet and indulged in excess.

What to do if your trousers become tight? The answer is simple: they need to be expanded .

We have accumulated a lot of experience in such alterations. We will tell you what to do to ensure the required width for your favorite clothes.

Stretch – suitable for shrunken trousers

If your jeans become too small, it’s not a problem. Denim, the main material for denim pants, has good elasticity and strength, which allows you to stretch them in the waistband right at home without “surgical intervention.” There are two most common ways to stretch pants.

Spraying

To do this, you will need a spray bottle into which you need to pour warm, clean water. After this, wet the belt from the inside and outside until the material is completely saturated with water. Stretch the belt with a few smooth movements. The main thing is not to stretch the material where there are abrasions, otherwise there is a risk of simply tearing the product. After the belt has dried, you can look at the result using a centimeter.

Soak

This method is more labor-intensive, but much more effective. You need to fill the bath with warm water and sit in it for some time, after putting on jeans. While soaking, you need to stretch the jeans in the right places with smooth movements. After this, it is recommended to do several physical exercises in them: squats, stretching, etc. You need to dry the jeans a little while they are on, then dry them in the fresh air so that they retain their body shape. If you use a hair dryer or dryer, the jeans will shrink again and the procedure will be useless. Soaking will help stretch the jeans not only at the waist, but also in other areas that cause discomfort, such as the hips or buttocks.

It is important to remember that both of these methods are only suitable for stretch denim. The material for dress pants may not survive such procedures and may tear.

It is also possible that the jeans will shrink again and return to their original size after several washes. If this happens, then more radical measures cannot be avoided.

Stretching trousers after washing

Many people are familiar with the situation when their pants shrink after washing. It’s not clear what to do in this case, because you really don’t want to throw away the whole product. Of course, if the pants get too long and start to look more like breeches, there’s nothing you can do about it. But if after washing the product has simply become a little narrow, a few tips will help to stretch it. For example:

  1. Don't wait for it to dry completely. As you know, many modern fabrics have the ability to stretch when worn. If you put on something that is still wet and wait until it dries on your body, then you will have no problems putting on your favorite trousers until the next wash.
  2. Steam the product. To do this, you don’t have to buy a special steamer or use an iron; just fill the bathtub with hot water and hang your pants over it for half an hour. You can also place them in a steam shower. The method has been tested by many and works 100%.
  3. Use a special expander when drying. If this is not available, a regular stick will do, which is inserted into the waistband of wet, buttoned jeans and left until completely dry. Thus, the expander will simply prevent the fabric from drying out, and putting on the product will be much easier.

Thus, with the help of these small tricks and ingenuity, you can not only extend the life of your favorite trousers, but also significantly save your family budget.

Belt insert

This method is suitable if the trousers begin to put a lot of pressure on the waist. To widen the trousers at the waist, you need a material identical to that used in the trousers and plain threads. A rectangular insert of the required size is cut out of the material, then the belt is ripped out. The insert is sewn into the belt as discreetly as possible. In addition to similar material, you can also use lace fabric (if we are talking about women's trousers or jeans).

You don’t have to insert anything, but open the dart a little and let it out a little in all the seams due to the allowances - suitable for a slight increase in size.

How to widen a jeans waistband

The wet material also stretches around the waist. To do this, you need to unfasten the button, carefully lay the product, for example, on the floor and use a spray bottle to spray warm water onto the tight area.

  1. You need to moisten it generously, the fabric should get wet through. Then you should step on the side part (in the pocket area) with your foot, and pull the opposite side of the belt with your hands, applying some force, but so as not to tear off the fittings.
  2. To expand the belt, you can take a bath while wearing a tight product. But first prepare a place for drying - spread a towel or oilcloth on the floor. The bath should be filled with warm water, it should be taken for about 15 minutes, periodically gently stretching the material around the waist.
  3. Drain the water and sit in the bath for a while to let most of the water drain out. To speed up the process, you can stand up, move around, and do a few squats.
  4. Then go to a towel spread on the floor, do some exercises (squats, swinging your legs to the sides, forward and backward), gradually stretching the clothes until they dry on your body.

For final drying, jeans can be removed, but not dried on heating devices or in the sun.

Triangular inserts


If the inserts at the waist are not enough, and the trousers also need to be widened at the hips, widening triangular inserts are perfect. More information on how to arrange trousers at the hips with triangular panels:

  1. First of all, you will need material. If the trousers turned out to be long after purchase and were cut off at the bottom, then these trimmings will also work. Otherwise, you will have to look for similar material in stores so as not to spoil the appearance of the item.
  2. You need to know how many centimeters you will have to increase your trousers. To do this, just measure the waist of your body and the waistband of your pants using a centimeter. The resulting number will be the desired difference.
  3. Cut out two triangles from the selected material with a width half as large as required (inserts are made on both sides so as not to disturb the symmetry of the product). On triangles, you must leave seam allowance on all sides.
  4. Then open the side seam (without touching the waistband) a few centimeters and sew in the triangular inserts. It is better to do this on a machine, simulating the main side seam.
  5. Cut rectangular inserts for the belt from the same material.
  6. Open the waistband and sew in the inserts.
  7. The better the material is selected and the higher the sewing skill, the better and more inconspicuous the inserts will be.

Sewing the wedge

By and large, this method is essentially sewing in the same triangular inserts, only of greater length. It is used if the trousers have become too big at the bottom of the hips. The width of the inserts is calculated in the same way as in the previous case, only their length increases. It is also necessary to take into account that this method of expansion is much more noticeable, so the inserts can be masked using small strips of material of a different color. Then the wedges will look original and not spoil the overall appearance of the pants.

How to stretch the waist of trousers with an elastic band

www.galls.com

Elastic waistbands stretch, but they have a limit. If this limit is too low, tailoring experts recommend using an iron to stretch the elastic band. The Kipkis electronic resource provides detailed instructions on this topic. To work you will need an iron, ironing board and a pair of washcloths.

Take just three steps:

  • Pull the trousers onto the ironing board, although it is acceptable to use pins if this will help hold the item in place;
  • turn on the iron at maximum power and place the wet fabric on the elastic band;
  • press the hot iron for about ten seconds, then let the pants rest for about 10-15 seconds.

see also

Choosing denim shorts based on your body type

Repeat this process for 5-10 minutes, moving the iron along the waistband.

aliexpress.ru

The waist will stretch. Repeat these steps as many times as necessary until you get the desired size.

see also

To tuck in or not - how to wear a shirt correctly

Increasing size with gusset

To prevent the pants from chafing in the groin, you can sew in a gusset. A gusset is a piece of fabric sewn in at the intersection of the side and crotch seams. The gusset is usually placed on home pants (tights or sweatpants, for example) or on children's clothes. Such trousers become much stronger, since there is no weak point where many seams come together. How to sew a gusset into pants:

  1. Cut out the gusset itself from a plain material. In most cases, this is a rhombus 20-25 cm long and 4-7 cm wide. Sizes must be selected based on the current situation.
  2. Open the crotch seam to a length slightly less than the length of the gusset.
  3. Baste or pin the gusset on one side, then machine sew with an inside seam.
  4. Perform the same operation on the other side of the gusset.

It is important to understand that the above describes the least labor-intensive way to sew a gusset, suitable for pants with a simple cut. To carry out the same procedure with trousers with a complex design, you cannot do without a competent pattern: on different models there are quite a lot of differences, both in size and in the location of the seams.

Increasing trousers size

If a situation arises when the trousers need to be widened not only in a certain area, but their size needs to be increased in general, this can be done with the presence of a so-called reserve, or allowance. It is important to understand that using this method you can increase your trousers by only one adjacent size (from 48 to 50, for example). For a larger increase, you will need to reshape the entire product. So, how to make pants a size larger:

On classic-fit trousers with a grosgrain, you need to get to the inner seam. To do this, the tape is ripped open, and underneath there is a seam that passes from the main fabric to the waist part.

  • Measure out the portion of the allowance needed to increase the size and make a mark with chalk.
  • From the mark, lay a new seam going to the existing one.
  • After this, you can rip out the old seam. The place where the old seam was must be completely cleared of threads and ironed.
  • All that remains is to sew part of the inner bodice in place. Thus, the waist part of the trousers will become one size wider.

To increase the size of trousers at the hips or in the groin area, sew in panels or gussets as described above.

Jeans are tight in the hips

The most common way to increase the size is to dry a damp product in natural conditions, while wearing it on yourself, at room temperature.

There are 2 options for drying jeans on yourself:

  1. Wet the product and put it on.
  2. Put on a dry item and then wet it, for example, take a shower in clothes.

The wet fabric stretches and shrinks to your figure during the drying process.

But wet clothes are unpleasant to wear, and the knees of completely wet jeans will also stretch out. It is not at all necessary to wet all the clothes - just applying it to the problem areas is enough. The liquid can be poured into a spray bottle and periodically moisten the fabric in those places where the clothes are tight.

Stripes - the most unusual option

Stripes are stripes of colored cloth that run along the entire length of the pants. Red stripes can often be seen on the trousers of command staff of the Armed Forces. In addition to their decorative function, they can also be used to increase the volume of trouser legs.

They are cut in the form of thin strips along the entire length of the trousers. To decorate trousers, you can use several thin strips, glued directly to the canvas using a special spider net and an iron.

In order to widen the trousers using stripes, you need to rip the side seams up to the waist, and then carefully sew the stripes into the trousers on both sides.

When choosing a material for stripes, it is necessary to take into account not only its quality, but also how the chosen color will look on the finished item. Bright colors go well with black tights: light green, pink, blue, and black stripes will look best on white pants.

From all of the above, we can conclude that the main way to increase the volume of trousers is to insert various pieces of fabric into the problem parts of the trousers. This requires not only knowledge, but also considerable sewing skill. Also, in most cases, you cannot do without a sewing machine and the ability to choose the right material. Therefore, if you are not confident that you will not make a mistake with the size of the inserts or lay an even seam, then it makes sense to contact a studio where qualified specialists will work on the item. Enthusiasts who do not have sufficient skills should first practice sewing inserts on things that are not used for going out.

Hello, dear craftswomen! Each person sometimes fits into his clothes, sometimes they become too small for him. Today we will learn how to embroider trousers at the waist, hips, if they have become too small, what tricks can be taken. Experienced dressmakers and housewives will share their secrets with us.

Volume expansion

Before you start working, you first need to decide how many centimeters you should increase the volume of your pants. This determines how the trousers can be widened at the waist and hips. Most often this is done using:

  • seam allowances and darts;
  • side braid;
  • elastic fabric inserts.

Before you pick up the scissors and make the first cut, you should make sure that in order to increase the waistband of your trousers, you cannot limit yourself to simply rearranging a button.

Increasing your narrow waistband by one size

If the product is just a little narrow, then the easiest way to increase its size is by using seam allowances and darts.
To do this, undo the belt. Then reduce the depth of the darts. In most cases this is enough. If the width is still smaller than required, then you need to move the stitching on the side seams closer to the edge. In many products, seam allowances range from 0.5 to 1 cm, and the edge of the seam is finished using an overlocker, so there is no need to worry about the fabric fraying. To widen the pants at the waist, it is not at all necessary to make a new stitch along the entire length; it is enough to make a smooth transition from the hips to the waist.

When everything that can be arranged is arranged and the width of the product at the waist suits you, one problem remains - the length of the cut-off belt is much shorter than the hem of the widened trousers. What to do? There is only one way out, make an insert into the belt. To do this, you can use a fabric of suitable composition and color.

For a solid belt, it is better to insert the insert in the front, in the fastener area. If the top of the trousers consists of several parts, then it can be placed at the seams by sewing a strip of fabric there. When the length of the belt is as required, it can be stitched into place.

Braid arrangement

The easiest way to embroider the sides of trousers is with braid. It can be purchased either ready-made or cut out yourself. It is sewn into the side seams. To do this you should:

  • rip your pants apart at the sides;
  • attach the braid to each edge;
  • overcast;
  • iron the seams on the product;
  • Sew decorative stitches on the front side.

The top can be decorated with an elastic band or a belt can be sewn in. For products made from thin, delicate fabrics, various laces can be used instead of braid.

Fabric insert

This method is used to widen the pants at the hips. To do this you need a piece of elastic fabric. This is the main condition, since the insert must stretch. A wedge of the required length and width is cut out of the fabric and inserted into the side seams of the trousers. In some cases (for products made of dense fabric), the wedge is made double. To properly insert the wedges into the sides of your pants:

  • cut the trousers at the sides to the desired length;
  • carefully baste the insert by hand, calculating its elasticity;
  • stitch on a sewing machine;
  • baste the cuts;
  • iron seams on the product;
  • decorate with decorative stitching on the front side.

Sometimes inserts are made not only on the sides, but also along the back seam of the trousers.
This is usually necessary in order to increase the product by several sizes at once. This does not look very aesthetically pleasing, so using this method without good reason is not recommended. If inserting from the sides is not possible for some reason, there is another way to widen the trousers at the hips - inserting fabric from the inside. To do this, cut the crotch seam to the required length and insert small wedges, as in the previous version. The only disadvantage of this method is that the fabric will have to be selected the same as that of the main product.

Don't throw away your trousers and jeans

This situation often arises when your favorite jeans become too small. What should you do with them, throw them away?

Don't rush, you'll still have time to throw it away. Let's find ways to deal with the problem ourselves.

If you bought jeans that are too tight, you can stretch them. Do this trick with them:

  • Take a spray bottle, pour warm water into it and wet the waistband of your pants well.
  • Then start stretching. Where there are abrasions, stretch more carefully and softly.
  • Don't let it dry right away. Stretch while drying, otherwise there will be no result.

Many girls simply sit in their jeans in a bathtub of water. Then they let them dry on their body without using any additional drying equipment such as a hairdryer.

Or wet your jeans and put them on lying on the floor, it’s more comfortable. Also let it dry on your body. After the next wash, the items may shrink again, then this procedure will have to be repeated again. What can you do? Take scissors, a needle and thread, and widen the pants where they are too small.

How to widen pants at home

If the jeans do not stretch over the body, then they can be put on while lying down - in a horizontal position, the stomach falls in and the process is easier.

To enhance the stretching effect, you can first put on thick tights, and only then pull on the trousers. They wear out gradually, so walk around the house, do your usual activities or do physical exercise. It will be better if you periodically moisten problem areas with warm water from a spray bottle.

  • A very good method of steaming is when the damp fabric is ironed or the effect occurs in the steaming mode, and then the still warm product is worn on oneself, preferably until it dries completely.
  • If you do not have a special expander, then you can use any available means - you can insert a strong board or hanger into your trousers, they can be pulled over the back of a chair or a suitable box or canister.
  • To stretch the product in length, it must be wetted with hot water, and then tightly wound around a cylindrical vessel (bucket, jar) and left taut until completely dry.

Attention! To increase your pant size, you don't have to wet them or take a bath in them. It is enough to take a textile product (scarf, towel), moisten it, put it on your waist while wet (wrap it), and put on trousers on top, walk in them until completely dry, move, bend over and squat.

The products are too small in the waistband, what should I do?

If the waistband is too small, it is best to sew in a small denim insert. The main thing is to find a piece of suitable denim. Open the loop, cut it to the required length, insert a piece of fabric or leather, baste it, stitch it on a machine. Sew the loop in place and that’s it, you can wear jeans!

If you have enough denim, you need to sew another belt and sew it on. At the same time, spread out and smooth out all the darts, then there will be no shortage in the hips.

It happens that just by cutting out the darts, the pants do not widen at all at the hips. All that remains is to sew in small triangular inserts. For inserts, you can use the material that remains after shortening the legs.

Let's figure out how to stretch your pants at the waist

With the advent of online shopping in our lives, we sometimes find ourselves buying clothes that are smaller in size than we order. Given the variety of fabrics, it is not surprising that clothes shrink even after washing.

We especially often encounter the problem of adjusting the waist of trousers and jeans. Changing the trouser waist is necessary if the waist varies between two standard sizes. You can order an item from a tailor or find a suitable store that produces non-standard sizes, or you can come up with options for correcting sizes at home.

LifeHacker experts have figured out how to stretch the waist of your pants without going to the workshop.
See also: The blogger showed a way to buy jeans by size without trying them on

How to sew a gusset

You can increase the size of your home sweatpants by sewing in a gusset:

  1. Cut out a rhombus from a plain material. Approximate dimensions: 20-25 cm in length and 5-7 cm in width.
  2. Open the crotch seam to a length slightly less than the length of the insert.
  3. Baste the gusset on one side, then machine sew.
  4. Do the same manipulation with the other side of the gusset.

You can also increase your trousers by one size (for example, from 48 to 50). Embroidering men's classic trousers:

  • Rip the grosgrain tape in the area of ​​the step, under which there is a seam that goes from the main fabric of the trouser leg to the part at the waist.
  • On the seam allowance, mark the new seam that is needed to increase the size.
  • Lay a new one from the chalk mark.
  • Next, undo the old machine stitching, remove the threads, smooth it out, and re-sew the grosgrain ribbon.

Decorating trousers with stripes

If your jeans are too small on the sides, then there are 2 ways to space them out by 1-2 cm. Do this:

  • Turn the product inside out and open the inner single seam where the jeans are too small.
  • Reduce seam allowances and sew a new line.

The second way is to increase the size with stripes - a wide strip of fabric. They are sewn in full length on the sides.

To arrange denim products you need to do the following manipulation:

  1. Open the side stitches to the waistband.
  2. Cut strips of fabric or leather of the required width with seam allowances.
  3. Baste from the outside, sew on a machine.

Today, any women's trousers are decorated with stripes. It is possible and beautiful. Many girls insert lace inserts and then flaunt new models of their own invention.

Reducing allowances

Products made from tight fabric can be expanded by reducing the allowances on the side seams.

  1. Initially turn the product inside out.
  2. Carefully open the waistband, open the side seams in problem areas, for example, from the hip to the knee, and iron. If you need to widen the product in the hip area, then you can leave the belt alone and rip out the inner seams rather than the outer ones.
  3. Use chalk or a bar of soap to mark a new stitch, reducing the hem of the side seams to make the garment looser.
  4. Sew new seams along the marked line.

The finished product should be ironed, paying special attention to new seams.

To prevent your favorite jeans from shrinking, you need to wash them correctly, following the recommendations indicated on the label. If the markings are no longer visible, then simply do not wash the products at temperatures above 40 degrees.

Bleach and regular powders are not recommended; it is better to use special liquid formulations. Compliance with the rules of care and storage, as well as delicate ways to increase the size will help you use your favorite jeans for a long period of time.

Repair using a spider web

Is it possible to increase the size of a product using a web? Can be expanded by the amount of allowance on the sides.

Cobweb is a special material consisting of thin adhesive fibers.

How to glue cobwebs to fabric?

  1. First, open the seams on both sides of the product and smooth it with an iron.
  2. Measure out the required amount of web. Add 1cm on both sides for overlap.
  3. From the inside out, apply the mesh so that the edges of the seams of the product are located close to each other, leaving no gaps.
  4. Using a heated iron, iron over the paper base, then remove it.
  5. Place the other side on top to cover the adhesive base by 1–2 mm.
  6. Iron the surface to ensure good adhesion. You can put gauze on top and iron through the gauze.

If the seam stands out, you can sew on stripes.

Such products must be washed by hand and not often, otherwise the cobwebs will come off.

An elastic band will come to the rescue

You can widen your trousers using an elastic band. An elastic band will come to the rescue in all cases when you need to increase the volume at the waist, when the trousers have become too small with a zipper on the side. Let's look at how to increase volume with a side zipper correctly.

  1. Steam out the zipper and remove the hard belt.
  2. Sew the side seam where the zipper was to the stitching done with an overlocker. If this volume is not enough, then insert a wedge of the required size and sew it in.
  3. Sew fabric to the waistband to fit two or three rows of elastic.
  4. Sew on a new belt, make two or three lines, insert an elastic band.

Increasing volume with elastic fabric or wide elastic

When everything possible has been ripped apart and placed, but the width of the trousers is not satisfactory, we make an insert into the belt. We increase the volume with an elastic band.

  1. We rip the side seams to the desired length.
  2. We remove the zipper in front and also remove the belt.
  3. We select the front and back insert to the width of the elastic, and sew it with the elastic.
  4. Baste instead of a belt.
  5. We sew it on a machine and process the cuts with an overlocker.
  6. To make the belt look aesthetically pleasing, we add additional stitches along the seams.

Such a transformation is only possible on a thin figure. Fat ladies can do a different manipulation.

How to hide a big belly

Not all women have a thin waist and a flat tummy. If you have a big belly, it is best to buy maternity pants. What to do if you have already bought the trousers, but your belly has increased? They can also be expanded.

In the trouser model you need to insert a fairly large piece of knitted fabric to match the color of the product. Knitwear should be dense, but have good stretch. The work is delicate, so it can be done by experienced seamstresses, but novice seamstresses can also try it.

  1. Rip out the side seams.
  2. In front, cut a piece of fabric from one seam to the other.
  3. Apply the cut piece to the knitwear. Trace with chalk, making seam allowances.
  4. Baste and stitch with a zigzag.
  5. Insert an elastic band on top.

Using extra fabric

This method is suitable for those craftswomen who have a sewing machine and have some skills in working with it.

Step-by-step instruction.

  1. Choose a suitable fabric that harmonizes in color or, conversely, a different color, bright and rich.
  2. Take a measuring tape and measure your waist, as well as the waist of your jeans. By simple subtraction, find out the difference between the two numbers, thereby calculating the size of the insert, allowing for a seam allowance of approximately 1-1.5 cm on each edge. The insert will be triangular in shape.
  3. At the back of the trousers, you need to rip off the belt with the back loop, make a triangular cut of the required size (to “grow” the jeans to the actual waist size).
  4. The shape of the patch is sometimes completed on a prepared piece of textile, guided by the cutout on the trousers.
  5. Secure the insert with pins, or better yet, sew it on by hand, taking into account the seam allowances, and try on whether the patch is the right size and whether it will be comfortable with a piece of fabric of this size.
  6. Sew the seams using a sewing machine, finish the edges with an overlock, zigzag or by hand, and gently iron.
  7. Sew the waistband and back loop.

After such an insertion, the clothes will be looser, without causing discomfort when worn.

Step-by-step guide with photos for repairing jeans that are worn between the legs

  • Wash and iron jeans that need repairing.
  • Cut out the most intact flaps from another selected item. Wash and iron them too.
  • Open the top crotch seam and the middle back seam (to about the middle or a little higher).

  • Using a ruler and a piece of chalk or dry soap, mark the part on one front side of the jeans as shown in the photo. The rubbed area should be completely behind the line. Make a seam allowance by drawing a second line parallel to the first.
  • Cut along the first marked line.

  • Place the cut piece face to face on the second part of the jeans, trace a line, also draw a second parallel line for the seam allowance and also cut along the first line. Seam allowances should be the same. Check that the cut-out parts on both sides of the jeans are the same: all edges and lengths must match.

  • Now you need to make a pattern for the insert. Take a sheet of paper (you can use thick polyethylene), place the piece cut out of jeans on it and trace exactly along the contour. On the sewing side of the jeans, make an allowance (the same as on the jeans). Cut it out.

  • It’s good if the pattern fits completely on the scraps of denim: trace it exactly along the contour (no allowances need to be made) and cut it out. If not, then the pattern will have to be divided into two parts as shown in the photo. Make a seam allowance. When arranging the details, make sure you don’t make a mistake. The parts must be mirrored.

You can do it differently: fold 2 pieces of denim face to face. Lay out the pattern, trace it and cut it out. You will get 2 necessary parts. Check that they are the same.

You can make a different insert, for example, using this pattern:

The detail on the jeans is cut out along the bold line. Also mark a thin line on the jeans, as in the photo. We make the pattern with an allowance of about 1.5 centimeters. Cut out 2 parts for inserts. We process the edges of the parts, marked with a dotted line in the photo, using a “zigzag”. We also process the cut edges on jeans. To sew the insert to the jeans, you need to tuck its edges along a thin line and stitch, retreating about 2 mm from the edge. Then apply from the front side of the jeans, where the part was cut out, baste so that the part fits exactly into the cutout on the jeans from the side of the middle and crotch seam (if there are any unevenness, straighten them out). The other edges of the panel should line up exactly along the thin line marked on the jeans. Sew along the right side exactly along the first line on the insert.

  • Place the top and bottom pieces face to face and stitch along the seam allowance line. If necessary, trim the edges by trimming excess fabric. Finish the edges of the seam with a zigzag stitch. Fold the bottom down and stitch along the right side with threads that are similar to the color of the stitching on your jeans.
  • Place the pieces face to face on the back of the jeans and stitch. Make sure that both sides match each other: the beginning, middle seams and the end of the inserts should be at the same level. Finish the edges of the seams with a zigzag.

  • Unscrew the inserts and stitch along the right side along them (with threads in the same color as the stitching), folding the seam over the inserts.

  • Sew the back middle seam. Fasten the end of the previously opened seam (reverse button on the sewing machine). The edges of the right and left inserts in the seam should match. Finish the edge of the seam with a zigzag.

  • Topstitch the seam on both sides using thread in the same color as the stitching on the jeans. Do not forget to secure the ends of the opened seams so that they do not begin to unravel.

  • On the inside of the jeans, mark the crotch seam by drawing a line with a piece of soap or chalk. If the jeans are also frayed at the seam, draw a line so that the fray is hidden by the seam: step back a few millimeters from the original seam line, drawing a new line to the bottom of the legs exactly along the original seam. Sew the crotch seam along the marked line, tack the ends of the opened seam and finish the edge with a zigzag. When sewing the seam, make sure that the edges of the inserts are at the same level.

  • Now you need to stitch the crotch seam with threads the color of the jeans stitching. Place the seam under the foot of the sewing machine, make sure that the seam allowance lies in the direction in which it was stitched earlier and stitch along one side of the seam, making a neat “tack” of the end of the previously opened seam. Then sew a parallel stitch on the other side of the seam.
Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]