Indesit W 84 TX: Instructions and manual in Russian

Detergent dispenser…

Page 2

Image
Text

W 84 TX, W 84 TK

Detergent dispenser (p. 14-15)

How to use the detergent dispenser and cleaning compartment

pourer.

Control Panel (page 5-7)

The design of the control panel of your washing machine is very simple.

hundred. Just a few buttons with which you select the mode

washing - from intensive, capable of washing even heavily soiled

New work clothes, up to delicate wool. Correct

choosing a mode guarantees high quality washing and a long service life

machine services.

Washing programs (pages 8-9)

A simple table will help you choose the right program, temp.

temperature regime, detergents, rinsing agents and softeners. You-

By choosing the right program, you get excellent washing quality

and at the same time save your time, water and electricity.

Maintenance and care (p. 26-27)

A little attention and care - and the washing machine will respond to you...

givenness and gratitude.

Not too burdensome care of the washing machine will extend the life

her service for many years.

Problems and their resolution (p. 17-20)

Before calling a technician, read these pages: many problems

we You can decide for yourself. In difficult situations, immediately call

Call specialists from an authorized service center.

10.

Technical specifications (p. 20)

Brief technical data that the owner of the style needs to know

ral machine: model, electricity consumption, water consumption,

dimensions, loading volume, spin speed, compliance with Italian

and European norms and standards, etc.

11.

Safety is a good habit (p. 28)

Read this section carefully - it contains the basic rules

safe operation of the washing machine.

Starting the car, How to get rid of stains: general recommendations

Page 4

Image
Text

W 84 TX, W 84 TK

Starting the machine

After installing the new machine, carry out a test wash without loading,

using program “1” at a temperature of 90°C.

Proper starting of the machine is very important for obtaining a quality wash,

preventing problems in the operation of the machine and increasing its service life

tations. After loading the machine and filling with detergents and various additives,

In addition, be sure to ensure that:

1. The car door is securely closed.

2. The machine is connected to the electrical network.

3. The water supply valve is open.

4. Handle A is in position l (Stop/Reset).

Program selection

The program should be selected according to the type of fabric (see pro- gramme table).

grams per s. 8-9).

•

By rotating the program selection knob A, select the program (combining

marker on the handle with the desired program).

•

Use temperature selection knob B to set the desired washing temperature.

•

Press buttons D, E and F if necessary.

•

Now press the on/off button G (position

- included).

Remember, if you want to use a programmed start, set

Turn it until you set the washing program.

After finishing the wash...

Wait for the I indicator to go out - this should happen approximately

3 minutes after the end of washing. Turn off the washing machine

by pressing the G button (position

- turned off). Open the car door. You-

After washing the laundry, leave the machine door ajar to allow it to evaporate.

remaining moisture. Be sure to turn off the water supply valve and turn off

machine from the network.

In the event of a power failure or self-shutdown of the machine,

This program is stored in the machine's memory.

How to get rid of stains: general recommendations

Ballpoint pen paste or felt-tip pen: apply methyl alcohol to a piece of cotton wool

and wipe the stain, then wash at 90°C. Tar and grease: remove thick layers of dirt, soften remaining margarine

nom or creamy mass, leave for a while; then remove with turpentine and immediately

then stretch the thing. Wax: Remove the wax, place the cloth between two sheets of loose paper and

iron with a hot iron; immediately treat with a cotton swab moistened with

pidar or methyl alcohol.

TK The same handle sets the delayed start of the program. IN…

Page 6

Image
Text

W 84 TX, W 84 TK

The same handle sets the delayed start of the program.

Select one of four delayed start positions, press the power button

switching/off G (position

- enabled) and wait 5 seconds. When tired

the new message will be accepted, the G indicator will stop flashing (will remain lit),

You can now set the desired washing program.

An indication that a delayed start is set is a special operating mode.

indicator bots: 2 sec. on, 4 sec. does not burn.

While the delayed start time lasts, you can open the door and

need to change the machine load.

After installing the program and accepting it by the machine, turning handle A is already

have no significance, except for installation in position

l (Stop/Reset).

Temperature selection knob

The handle is designed to select the washing temperature according to the table

programs (see pp. 8-9). In addition, with this handle you can install

change the temperature below the recommended temperature or perform a cold wash

(character B).

Detergent dispenser

The detergent dispenser has three compartments: 1 – detergent for pre-wash; 2 – detergent for washing; 3 – additives (softeners, flavors, etc.). Additional compartment 4 (included in the accessory kit), intended for

started for bleach, is inserted into compartment 1.

Detergent dispenser

with additional insert for

bleach is here.

Most popular programs

Indesit washing machines have many modes. Some modes are used much more often than others.

Article on the topic: What is better: a washing vacuum cleaner or a regular one

Users of Indesit washing equipment most often use the following programs:

Mixed things (the program is indicated by number 3 on the selector);
Wool (indicated by the number 14);
Moderately soiled non-fading synthetics (indicated by the number 9 on the selector);
Heavily soiled white items (number 1)
.Colored things (number 4);

To wash heavily soiled white items, select washing mode 1. This is done using the program selector. Use the temperature selection toggle switch to select MAX or 900C. If you don’t need to boil the laundry, you can set it to 600C. There is no need to choose a lower temperature.

The number 3 on the toggle switch indicates the “mixed things” program. This program is the most universal and is used most often than others. It is chosen when washing faded colored items or white, non-fading colored laundry. In the first case, the temperature is set to 400C, and in the second – 50-600C.

The number 4 indicates the “colored things” mode. This mode is necessary for washing lightly and moderately soiled items. The water temperature is 400C. However, this mode can be used to wash not only colored but also white items.

For synthetic items it is better to use the mode number 9, and for woolen items – number 14.

preventing wrinkles...

Page 7

Image
Text

W 84 TX, W 84 TK

Easy ironing (prevents wrinkles)

This feature allows you to wash without wrinkles on the

linen, making it easier to iron later. The D button can be used

with programs 3-4 (cotton), 5-6 (synthetics), 8-9 (delicate fabrics).

When you press button D on programs 5-6-8-9, handle A will stop at sym-

will. You can end the wash by pressing button D again.

Important: This function cannot be used in conjunction with the "Output" function.

“Spot Removal” (button F pressed).

Slow spin

Use the button to decrease the spin speed:

from 800 to 400 rpm. — washing programs for cotton fabrics;

from 700 to 400 rpm. — synthetic washing programs.

Removing stains (see page 16)

This button sets the intensive wash mode. Efficiency of use

the number of additives to the detergent increases, while removing

the most persistent stains. After clicking this button, you will not be able to play

use the pre-wash mode.

On/off button

Pressing the button turns on the machine. If the G button is not pressed, the machine

off.

Turning off the machine does not cancel the set program.

On/off indicator

The H indicator flashes when the machine is turned on and is waiting for a program to be entered.

Steady lighting of the indicator means that the task has been accepted.

Door locked indicator

A lit indicator indicates that the car door is locked to prevent

tion of her unexpected discovery. To avoid damaging the locking mechanism,

Wait until the I indicator goes out before opening the door. Indica-

The light will go out 3 minutes after the end of the wash.

Repair and operation of Indesit washing machines

_____________________________________________________________________________________

WISL models
Models WIUN, WISA, WIA
Models IWSC, W, WITE, IWUD, NWS, WITP
Models IWSD, WITL, WIL, IWUC
Models ITW, WISN, BWSA, WISE, IWUE, WIUL
Error codes

Indesit iwsb 5085. The hatch lock failed. I changed the lock and the exploded triac Q018 Z0607. Water is poured in, then the pump turns on and drains endlessly. The top (horizontal) row of indicators blinks. It can only be turned off by using a plug from the socket. The periphery is normal. I noticed that the factory triac was soldered incorrectly (turned 180 degrees). I soldered it as expected. On these modules the UBL circuit is connected to the motor circuit, check everything. These triacs are soldered 180 degrees relative to the picture on the board; if there is a simple UBL, according to the picture, another triac is soldered in under the “fast” lock. Indesit iwub 4085, UBL was replaced with the original UBL. The drum works - it's working, the engine is intact, there is some darkening on the electronic control board, but it's probably from the belt. If the UBL is new, then it is very strange and a diagnosis of SMA is necessary, because flashing lock means the UBL is broken. The win 102 machine begins to fill with water, then the lock and dirty laundry indicators begin to blink. She doesn’t start the wash, but starts draining the water! What could it be? A flashing “lock” and a lit dirty linen indicator means error F04. Most likely, the water level sensor is faulty or the control module is faulty and the processor needs to be rebooted. The Indesit ws84tx washing machine is in operation. Apparently, over time the oil seal wore out and as a result the bearing began to knock. I decided to open it up and, if possible, repair it (by this time the unit had been out of service for about six months). I got to the point of removing the crosspiece without any problems, but I removed the crosspiece only with the help of a puller (it looks like the bearing had time to rust). Moreover, the outer race of the bearing remained in the crosspiece, and the inner race had to be removed separately from the shaft. The shaft is clean and smooth, but on the bronze bushing (at least it looks like rusty metal) there is a groove from the oil seal. Does it make sense to continue repairs with such wear on the shaft? And if yes, then tell me, in what order? The oil seal was: ROLF 35 52/65 7/10.5. Bearing: SKF 30x60x37 BA2B 026298 633667. Bearing (code 26298) 30x60x37. Polish the bushing, it will still work (if you assemble it properly). 1-press in the bearing. 2-insert the oil seal into the crosspiece. We put the 3-cross on the drum shaft and fasten it. Washing machine Indesit ws105tx, only the wash cycle works, drains the water and does not go on to any more cycles (rinse, spin), it can be opened if you manually set the end of the program. After that, it doesn’t work right away in the wash, it can only turn on after a few hours and then everything repeats. I apparently explained it incorrectly; when I press start, the hatch is blocked, but after stopping the car, I manually flip the program selection knob until the cycle is completed and the lock snaps back to open the hatch. Most likely the water supply valve has failed. The valve consists of two parts - one supplies water to the main wash, and the second to rinse. So, it supplies water for the main wash, but not for rinsing, and the unit does not switch to the next mode. If the valve does not work, it must be replaced with a new one. Malfunction of the Indesit Wiu 80 washing machine. After turning on the washing mode, a small amount of water is poured in (the powder is not washed out of the box) and the door lock indicator and 3 more indicators (rinse, spin, spin speed) begin to flash frequently. After this, the washing machine stops responding to any buttons. Only turning off the network helps. Or is it the control unit? In your case, blinking - “lock”, “spin”, “rinse” and “revolutions” - this is error F11. Most likely, the drain pump has failed and needs to be replaced. Machine iwsb 5085, description of the problem. She pours water, the drum rotates for a couple of seconds in one direction, stops, then 2 more times, a couple of seconds each, in the opposite direction and silence. The indicators light up as expected, programs switch, but on any program, the drum rotates 3 times. When turned on, it does not show any errors. The drum rotates easily, I checked the tachometer - it works. The issue was resolved by replacing 4 resistors (tachogenerator circuit), after several weeks of proper operation, the lock indicator began to blink, the washing machine did not work, the lock did not lock. Possible error F01. I'll look at the triac. It makes sense to check the engine for breakdown, for example. Length of brushes, condition of commutator, connector. The UBL circuit still needs to be looked at. Indesit iwub 4085 cis. The machine was washing and then turned off. Later, when you turn it on, an error appears. I can’t figure out what the error code is for this model and electronic module. I checked the heating element, NTS sensor, power button, and power supply in the module. I removed the module and the display panel and connected them separately, the same error comes on. Tell me what the error is and what to check next. The horizontal ones all blink, and 3(9h) and 4(12h) (from top to bottom) are constantly on. Apparently, error F12 (when all horizontal lights are blinking, the spin and drain lights are on). Reflash the module (minimum to start with). If that doesn't help, replace the module. The iwub 4105 cis washing machine is in operation. And here’s the problem: I turn it on and start any wash cycle, it fills with water, but it doesn’t start the wash. All buttons light up and blink approximately 3-5 times per second. At the same time, a sound is heard as if a drum is spinning - although in reality it is not spinning. I turned on the rinse cycle and the machine started working, but during the spin cycle everything happened again, but without any extraneous noise. She just blinked all the buttons. Tell me, what could it be? And how to fix this? If all the indicators are blinking, then the reason may be a current leak to the housing. The leak may be due to a breakdown of the control module, motor or heating element. Indesit ws105tx. At low speed, in washing or spinning mode, the motor cannot turn the drum, but at high speed, 800 or 1000, it turns without problems. What kind of malfunction is this? How is speed controlled in this model? What voltage should be on the brushes and on the stator in the washing mode and in the spin mode? Take out the brushes and measure how long they are. Possibly a short circuit in the stator. The ws 84 tx machine stopped rinsing, but the laundry was wrung out, everything is fine. I tried to turn on the rinse mode again, it didn’t even draw water, and then I just wanted to start the “quick wash” program and it stopped drawing water at all. What to do? The washer has stopped rinsing because it cannot get water. This is the root cause. The most common reasons: a malfunction of the inlet valve, which opens to fill in water; control module malfunction; The pressure switch, a sensor that controls the water level, has failed. Indesit IWD 71051. After washing, I started spinning and stopped. All buttons are lit and error F11. We checked - there is no garbage. Maybe the drain hose is clogged? And if it’s a pump, how much will it cost compared to the cost of the pump? Error F11 means a malfunction in the drain pump circuit. The Wiu 81 machine, when you turn on the washing program (any), it fills with water for 20 seconds and stands up, the drum does not turn, but the heating element heats up. If you add water manually through the tray, it comes to life and continues to wash until the 2nd cycle, then you also need to manually add water, otherwise it stops. In the last cycle it fills itself, and there is no need to top it up manually; the wash ends on its own. What has been checked: both water intake valves are working, the heating element is working (29 ohms according to the multimeter, it doesn’t ring on the case), the tachometer is working, the pump is working, the motor is working and the brushes are working too, the commutator on the motor is clean, the board is visually in order; condensates, diodes rang normal. True, I couldn’t ring the pkc 136 diode - the multimeter shows 1 in both directions, but it seems to be working. Suspicion of the pressure switch or I can only think about the control board (maybe the firmware is faulty). The pressure switch itself seems to be a working 4-pin, single-chamber one. Three modes work, if you blow it manually and ring (empty tank, full, overflow), everything is normal. The potentiometer with which you set the programs works normally and the reset works. You have already checked everything possible. If the water does not fill up completely, then the problem is either in the pressure switch (water level sensor) or in the control module. The module can burn out in such a way that all the microcircuits and capacitors are intact; check the valve for a closed circuit through the wires and the control module with the microcircuits to the pressure switch. The Indesit iwub 4085 machine stopped turning on. After washing, you plug the cord into the network, it does not react at all, the power light does not light up and the other lights do not light up either, as if there is no electricity, the socket is working, we checked it. What could it be? If the washing machine stops working when plugged into a working outlet, you need to check the power cord for kinks or breaks and check whether the interference filter has burned out. Malfunction of the iwsb 5105 washing machine. The drum does not start in the washing mode, but spins during rinsing and spinning. It seems as if the water is simply poured in and drained. I turned it on without checking how it worked, but it kept running water for an hour and a half, with only the underwear underneath getting wet. I opened the pump, but it didn’t help (it somehow corrected the situation when it wouldn’t start at all). I think the pressure switch is faulty. When rinsing, I also noticed that the water was not getting in, although it was spinning. In general, it’s a problematic model, even though it’s new (more than a month old). Initially, it stopped when switching to rinsing and worked until you turned it off, so every wash I change the programs manually - first wash, then rinse, then spin. But this doesn't bother me too much. At the moment I am concerned about the problem with the drum. It drains, but there is no obvious sound of the pump operating. Just once, to check, remove the drain hose from the sewer and lead it to the bathtub, sink and do one wash. SMA ws 105 tx. Previously, there was a noise when the drum rotated in the spin mode, then it began to make noise in the washing mode too. We turned it on to mode 7, the water filled, but the drum does not rotate, only the quiet hum of the engine can be heard. I drained the water, tried to turn the drum by hand - it turns in increments of 10-15 cm and everything stops. I tried to rotate the drum with play in the longitudinal direction - the drum began to rotate by hand, but it still refused to wash, water filled in, the drum did not rotate, only the quiet hum of the engine was heard. What could be the reasons? Perhaps the belt or bearings have fallen off, it's time to change. SMA Indesit ws84tx does not include a second water fill valve. The program starts normally, then the water fill is turned on, then there is a pause, it should turn on after topping up, but this does not happen. Follow the wires to track where the valve connector is located, and look along the tracks for non-working elements of the module. My machine has this problem, while it washes everything fine, when it starts rinsing, the lights start blinking. Then it doesn’t turn off and blinks until you pull it out of the socket, then you plug it into the socket and it continues to blink and there’s nothing you can do. Tell me, what problems could there be? If the wash delay, dirty laundry and lock indicators are on, then this is error F12, which means the loss of indication between the module and the command buttons. The reason may be either in the wiring or in the control module. The Wiu 100 washing machine is installed and connected. When it reaches the “spin” mode, it turns off, during rinsing, it practically does not rinse, after it turns off, the lock and speed indicators flash (500/1000). Tell me what to do? A lit RPM indicator of 500/1000 means error F08. Either the heating element or the control module has failed. The Indesit Wiu 61 washing machine is in operation. The wash starts, takes in water, but washes with long pauses of 3-5 minutes. The water does not drain, even when changing the program to drain, but the operation of the drain pump is barely audible. I checked the filter and pulled out a couple of coins! Please tell me what the problem might be. The drain pump in the SMA has failed. It's very easy to check, just measure the resistance. If the pump resistance is outside the range of 160 - 200 Ohms, then the pump is broken. The machine is iwsb 50851, it pumps water, but the programs do not turn on, and the first indicator blinks. When the first indicator is on, it means error F08. This is a problem with the water heating system. Most likely, the heating element has burned out, after filling the water it cannot heat up and the fault code is on. Washing machine Indesit iwsb 5851. Starts to fill with water and drains after 15 seconds. All horizontal indicators and the top vertical one, where “3h” is written, begin to flash. If you set the “rinse” or “spin” mode, it does them without problems. Tell me, what is the error code? Slowly add water, then clean the inlet valve mesh. The iwub 4085 washing machine does not turn on, that is, when the power is applied and “start” is pressed, there is no indication or other reaction, the previous wash completed normally, after which the unit was not turned on for 5 days. Disassembled and inspected. Power comes through the input filter to the control unit - code 21501264600 seems to be leaving it (but I’m not sure about this, since there is no circuit diagram). I pulled all the connectors, the contacts are all dry, not oxidized, there are no signs of water ingress. The SMA is new, the warranty expired 2 weeks ago. Question: How can I verify the serviceability/failure of the control unit? What can be done with the block (I read that it can be reflashed). My further diagnostic steps if the problem is not in the control unit. Turn on the SMA and wait 10-15 minutes; if F12 appears, the module needs to be reflashed. The ws84tx washing machine with laundry does not spin the drum, but goes through the entire cycle when empty. Most likely, either the electric motor brushes or the drive belt are worn out. The contact is no longer sufficient, and the rotor force is not enough to rotate the drum with laundry. Indesit iwsb 5085, during switching on, the circuit breakers in the panel tripped. Turning it on again produced a quiet noise in the form of a pulse in the Arcadia module. The check showed that the triac did not work, since the relays did not work; after replacing the triac, the water valve came to life. The water started pumping, but immediately the water drain worked and the top row of indicators began to blink and 3h seemed to be blinking dimly. The top row shows that the SMA is not working. Check, measure, the triac just doesn’t light up - this is a consequence, look for the cause. The error is shown in a vertical row, count from bottom to top using 5 indicators. Malfunction of the IWB 6105 washing machine. Transported, installed, does not turn on. You can hear a quiet squeak when plugged in. During transportation, one of the contacts from the interference filter to the control module could fly off. Check it. To access, simply remove the top cover of the washing machine and check all contacts. Washing machine Indesit iwub 4085. It began to make a lot of noise during the spin cycle. And the last time, during the next spin cycle, a lot of stones or scale came out. What could it be? As far as we understand, after the stones and scale came out, the noise during the spin cycle did not stop? The most likely cause of the noise is wear on the drum shaft bearing. It needs to be replaced. If the reason is indeed in the bearing, then after a while the unit will stop pressing. I have a question, the “Start” key and the first key (with the 3 o’clock indicator) are lit at the same time. What to do? If the power indicator is on and the drain indicator (3H) is blinking, then there is a malfunction in the water heater (heater) and it needs to be replaced. The Indesit Wiu 82 washing machine is installed and connected. When you plug the plug into the socket, the inlet valve knocks at a frequency of a couple of times per second, and water immediately begins to flow. The door is locked and no indicators light up. Most likely the water supply valve is faulty. The valve solenoid has failed. Indesit Wiu 80, turns off during the wash cycle, the lock indicator goes out. What could be the reason? If such actions occur 5-15 minutes after the start of washing, then the reason may be the failure of the heating element. To avoid short circuit wiring and fire, the device resets the program. Washing machine iwsb 5085 cis, drain pump replacement. Please help me choose a replacement pump. Written Askoll M231, and 34 watts. Terminals for the chip. But for some reason the M231 catalogs have separate terminals. Its terminals are the same as mine, and the chip key is in the same place. But the power is not 34W, but 30. The water is not drained every time. I think it's the pump. Isn't this difference in power critical? Install any one, and in order not to redo the terminals, just rearrange the coil, don’t pay attention to the power. I disassembled the iwub 4105 SMA, during reassembly I connected the motor terminals incorrectly (vice versa), then I turned on the program, but the motor does not work. I rearranged the terminals correctly, the engine works, but incorrectly, it turns for a short time and stops, although it should work constantly. It collects and drains water. What is the problem? I also removed the top counterweight. I tried to wash it with things, the machine started jumping. You have burned out the current limiting SMD speed control resistors on the ARCADIA module. Contact a specialist. SMA Indesit iwsb 5105, when turned on, the top four green LEDs blink, plus the two outer ones are lit. Doesn't respond to buttons. Board EDT0117.11. I checked the output voltage from the power submodule, there is 12V. I checked both capacitors on the power supply, they are normal. Is it the firmware that has crashed or is there a malfunction of the element base? The testing procedure does not start 9h (9h) is on. Is there any way to do this without a programmer? If 9h is on, then it is F08. But with a lock - F09. Washing machine Indesit ws105tx. For example, you set it to the first mode and it can wash without switching for 5 hours until you notice and switch it yourself. This problem occurs in all washing modes, but not all the time. It also happens that it fills up and immediately drains water, sometimes the programmer starts walking in a circle, without stopping until you unplug it from the socket. In operation for about 10 years, the only repairs included replacing the bearing and cleaning the drain pump twice. You need to turn off the hot water and check whether the heating element really heats the water. Check for self-draining. Washing machine 789 W, during operation there is a chemical smell inside and smoke appears, what should I do? Most likely there is a problem with the wiring. We do not recommend using such a malfunction. Indesit IWSB 50851. In the washing mode, it picks up water, immediately drains, begins to flash the upper row of indicators, and the “start / pause” flashes in yellow. In rinsing mode, it picks up water, twists, drains in 5 minutes, begins to blink, stops twisting and the pump periodically turns on just like that. Horizontal series shows that SMA does not work. In the vertical series, only the lowest button flashes? Then error F01, with all the ensuing consequences. In operation, the IWUB 4105 washing machine. At the launch of washing, the Start, Washing indicator and blinks the Luke lock indicator. The wash cycle does not start. What could be the problem? Most likely, we are talking about an error F04 (the receipt of the signal overflow and empty). The water supply valve or a press start (water level sensor) is faulty. The IWSB 6105 Indesite washing machine was a closure on the network. Changed the heater, the castle, it earned, but it stops in the process of work, and all the upper lights blink. If all horizontal indicators burn, then this is a F09 error. Most likely, the control board failed. The washing room worked yesterday, and today, when turning on, even the indicators do not burn, I checked the voltage on it and then went on a fee. What to do? If the electricity reaches the control board, through the network filter, then, most likely, the case is in the control module. We recommend checking it. Try, in the same way, turn off the unit for 20-30 minutes to reboot the processor. Indesit IWUB 4105 CIS. All indicators blink, the lock is constantly on. When examining the module, a burning component of Q018 was found. The marking, unfortunately, cannot be read. What to replace it with? What else to check, maybe he still pulled something behind himself. Q018 is the Simistor of the UBB. Its marking is Z0607. Call three SMD diode surrounded by a resistor at the bottom of the board. Ubble is definitely a replacement. Or KZ in the connector or burning with ub. The Wiu 102 Indesit washing machine, the “squeezm” indicator is on, turn off, turn it off, nothing changes, does not erase, does not gain water, begins to immediately squeeze. What to do? If the squeezer indicator burns and the lock indicator flashes, this means error F01, which is associated with a malfunction in the engine. Failure to the IWUB 4085 CIS washing machine. After turning on the washing, it makes 3 revolutions and the hatch blocks, quiet clicks are published 1 time per second, what is the reason, tell me? If only the hatch is blocked, then the matter is in the breakdown of UBB (Luke lock device). Check if nothing interferes with the closing of the hatch. If not, then diagnostics are necessary and, if necessary, repair the master. Also, try turning off the device from the power supply for 20-30 minutes to reboot the processor. Indesite WiU 82. Gains a full drum of water, stops only when you turn off the outlet. When filling with water, the drum does not spin and not a single light burns. And water can only be drained through the hole, which is located under the lid. What is the problem? Tell me, and is it possible to fix it yourself? Look at the water level sensor, a pipe goes to it, blow it. Remove the top cover, you will see everything there. I have a Wi84X Indesit machine. In the first and second washing modes, she just goes crazy. That is, he will heat up the water to 90 degrees, and then the handle of the regimes simply spins and that’s it. And in the third mode she does not want to fill in water. Most likely, a failure in the operation of the drain system. The IWB 6085 washing machine. During the washing, I heard a strong rattle, and a white plastic chip appeared on the clothes, I have been using it for about 5 years. Tell me what the reason can be and whether repairs are possible at home. The rattle can be due to wear of the bearing. Replace the seals and bearings. In the work, the IWUB 4105 washing machine. When turning on, the water is typed, and it calms down, that is, the indicator of washing and blocking the door burns, and the drum does not twist, and the sound of the motor is not heard. He does not respond to other programs until he turned off the outlet, then turned on to drain the water, the pump works. What could be the problem? What exactly indicators are burning will say what kind of malfunction. The WS 84 model was erased at night at the “5” program (with a stop before the spin and to take it out by hand). In the morning, the program switch walked in a circle, and the turning point indicator flashed (ready to turn off). When I took out linen, there was no water in the unit, but the linen was not unraveled. Today I turned on again, the inclusion indicator caught fire, the lock was blocked, but washing did not start. I turned my hands with the handle of the programs to the point "Stop". The smell turned off and the door was unlocked in the prescribed manner. I tried to start washing 2 more times and everything was repeated the same. Question: What is it connected with? This may be a programmer problem (control element). The heating element or a fill valve can also be damaged.

_________________________________________________________________________________

_____________________________________________________________________________________

Operation of the LG SMA I bought an LG E10B8ND DD washing machine and have only washed it 3 times so far. The problem is this. It washes very quietly, since the all-wheel drive goes directly to the drum. Even spinning at 1000 rpm is quiet, but when it drains...

Samsung WF 8590,6450,6520 We repair the Samsung WF8590NMW8 diamond washing machine (5 kg load). The DE error appears on the display, although 220 is supplied to the lock itself (checked). The most interesting thing is that I decided to test the lock on another SMA, and it worked. Has anyone encountered...

Ariston RSM, WMSF, AVTL Washing machine Ariston avtl 104, with vertical loading 5 kg. The situation is very unclear. SMA can wash off normally, but recently it has started to behave strangely. When rinsing, it stops and the indicator on the power button goes out...

Indesit IWSB, WS, WIU, WIN Machine iwsb 5085, description of the problem. She pours water, the drum rotates for a couple of seconds in one direction, stops, then 2 more times, a couple of seconds each, in the opposite direction and silence. The indicators light up as expected, programs switch, but...

______________________________________________________________________________________

FAULTS AND REPAIRS OPERATION AND SERVICE ERROR CODES

______________________________________________________________________________________

Repair of Bosch Maxx 5 automatic washing machine. Bosch maxx 5 speed edition WLX 20463 OE washing machine in operation. I began to perform the washing program incorrectly. We set the hand wash program, the spin was completely turned off. After washing, SMA switched to rinsing...

Candy Aqua, GVS4, GS3, CS2 There is a smell in the gvs4 126dw3 washing machine. I wash with the addition of liquid Calgon, but there is no effect. Sometimes I rinse my laundry with vinegar. If the linen is thin, like bed linen, then it does not smell. But the towels started to smell. What to do?

Electrolux EWW, EW, EWX The Electrolux EWW 1686 washing machine is in operation. It started tapping when washing, regardless of whether it was spinning, stopping before changing modes, or washing. It knocks periodically, not all the time. The sound comes approximately from the control module...

Zanussi ZWY, ZWSE, ZWT Washing machine zwy 51004 wa, bought about a month ago. I set the washing program, the final spin occurs, and the machine starts washing again, and so on ad infinitum, until you just turn on the water draining program. What could be the problem?

Repair of Ardo SED, TLN, FL Ardo TLN 126. It has a display, and when you turn on the washing program, the washing time is displayed. Gradually it should decrease, but here it is. I turn on the 20-minute wash, but in the end it takes 40 minutes or even more to wash, and the time is constant...

Beko WKB, WN, WKE, WM Model WM 3350 E. We started working in the “short wash” mode, the program worked completely (the door unlock button lit up), but water remained inside. In fact, rinsing and spinning did not work. When I tried to reboot, nothing changed, the sensors...

Repair of ACS Gorenje WS,WT Model WS 43100. The fill valve does not open. Writes "Error 9". This is an error related to aquastop. There is no aquastop. I bought a new non-original valve, took the coils from the old one, put it on with difficulty, one might say, hammered it in. I installed it, did a couple of washes...

Whirlpool AWE, WTLS, AWOC We bought a Whirlpool AWE 6516 washing machine with top loading and electronic control. Container for detergents under the lid. I pour the conditioner into the container, and it immediately pours out of the small...