Instructions and manual for Indesit IWUB-4085-(CIS) in Russian

Motor brush wear

Graphite brushes are a component of the commutator motor that ensures its rotation. They transmit voltage between a stationary stator and a moving rotor. When the brushes wear out, weak contact occurs between them and the commutator, the electric motor loses power, jerks or does not rotate at all.

*Parts are not included in the price and must be paid separately.

Water leakage

The presence of a leak indicates a hole in the rubber cuff sealing the hatch. If the cuff is not damaged, but water is leaking, you should clean the lower part of the door glass from the inside.

During operation, dirt accumulates in this place, worsening the contact between the glass and the rubber seal. To eliminate this problem, simply wipe the glass with a cotton swab dipped in nail polish remover.

Washing machines of the Wisl series provide additional protection for the housing against leaks.

The body must be level

It is important not only to install the Indesit machine, but also to align it with the floor. This is the only way the machine will be stable, which will eliminate strong vibration, knocking and “jumping” around the room. If you ignore this step, even automatic imbalance control will not save you, and the unit will break down faster and require repair.

Leveling occurs with the help of adjustable legs, making straight lines possible even on curved floors. The fitting process looks like this:

• put the building level on top of the washing machine and, using it as a guide, unscrew or screw in the legs;
• we lower our hands to the corners and slowly pump the equipment (if there is no vibration or strong rocking, everything was done correctly, otherwise, we go back and repeat the adjustment);
• tighten the fixing nuts on the legs using a suitable wrench.

The best test is to start the mode at maximum spin. Even at high speeds, the unit should not move independently in space. Special vibration-smoothing attachments, which are sold in service stores and supermarkets, will also come in handy.

Where should I put the detergent?

In older models of Indesit washing machines, detergent is poured into the dispenser. It is unacceptable to add powder for hand washing into the cuvette. This will lead to excessive foam formation and equipment failure.

Order of compartments:

• 1 compartment – ​​powder for pre-wash;
• 2 compartment – ​​powder or gel for the main wash;
• 3 compartment – ​​additives (flavors, conditioners), the compartment should be filled no higher than the installed grate;
• 4 compartment (not available in all old-type SMAs) – bleach.

Once the detergent is in the desired compartment, the dispenser is pushed back. Then you need to check again that all the steps have been completed correctly, and then click on the “Start” button.

Electric motor

A commutator type electric motor is installed here.

The most common problems:

• Brushing of brushes. Occurs if you use the device too often. When starting the program, it does not start working, which indicates a breakdown of the main motor brushes. The parts are paired and must be replaced at the same time for correct operation of the motor.
• Peeling of lamellas on the collector. The lamellas peel off most often in old devices when the brushes rub them into holes.
• Break or interturn short circuit in the rotor and stator windings. If there are any signs of winding burning, the motor must be completely replaced.

Electric motor failure is also determined by the lack of rinsing and spinning. If the washing machine heats the water and washes, but when moving to the final modes the engine starts to turn idle, this means that the engine is broken and must be replaced.

First wash

Before using the Indesit washing machine constantly, you should run the first wash cycle. To do this, you need to pour washing powder into a special tray, set the maximum temperature to 90 degrees, without adding laundry. This will remove any possible unpleasant smell from plastic, rubber, or metal components.

Connection rules

After purchase and transportation, the washing machine is unpacked and installed. Before connecting, you should read the operating instructions, which come complete with a warranty card for service in case of breakdown and a receipt confirming the fact of purchase. The user manual describes in detail the main points that explain how to use the Indesit washing machine for trouble-free operation.

Before installation, be sure to remove the transportation bolts. Level the washing machine as follows: twist the legs under the front of the device for a stable position. This will prevent noise and vibration during spinning.

The drain hose must not be kinked. The drain hole is installed at a height of sixty-five to one hundred centimeters above the floor. Dirty water should drain freely and the end of the hose should not go into the water.

The socket into which the washing machine is plugged in is grounded. The plug must match the type of outlet. It is not recommended to touch wet parts of an electrical appliance that is plugged in: electric shock may occur.

Various blockages

Blockages in the drain system are considered one of the main problems with Indesit washing machines. If the drain hose and filter are clogged, the machine stops draining water. If the model is equipped with a display, error code F05 is displayed on it.

Cleaning the filters yourself is not difficult even for those who do not have the skills to handle equipment. To clear the blockage, you need to open the bottom door on the front panel, lay rags on the floor or place a flat tray and pull out the catch filter, rotating it counterclockwise.

Garbage and small objects (coins, buttons, pins) accumulate here. After cleaning the filter, the unit is ready for use. This procedure is recommended to be done once every few months as a preventative measure.

We suggest you read: How to remove stubborn oil stains

How to set the desired mode?

The selection is made using the programmer knob. There are inscriptions and icons around the selector switch. On older models there are no verbal designations - only icons, hence the problems with choice. It happens that the owners of the machines do not understand the images, then they need instructions to decipher the symbols. In the new models, the manufacturer took this omission into account - all icons are duplicated with words.

Before you set the mode, you need to sort the things that you are going to wash. Evaluate them by type of fabric, color, degree of soiling. Taking these positions into account, a decision is made: choose a ready-made program or customize your own. If preference falls on the second option, then the user selects:

• temperature;
• duration of the process;
• rotational speed.

Whether a ready-made program is included or your own is being configured, the user can add additionally:

• soak;
• rinsing;
• light ironing;
• spin

The process can be delayed for a certain time, depending on the duration of the timer. Typically, the maximum delayed start time is 24 hours. Descriptions of the modes can be read in the instructions.

Do-it-yourself repairs, is it worth it?

Whether to start repairs yourself or call a repairman is up to the car owners to decide. It all depends on your own knowledge, skills, financial capabilities, and availability of free time. In any case, this is an excellent way out of a difficult situation, because if the repair is done with your own hands, this guarantees:

• savings, you only have to pay for spare parts;
• speed of work, no need to wait for your turn;
• quality, complete confidence in the correctness of the repairs.

In the vast majority of cases, do-it-yourself repair of an Indesit washing machine is justified, of course, if you have certain skills. It is also worth noting that you can only take on work related to complete or partial disassembly of the machine if its warranty period has expired. Otherwise, this is a loss of warranty with all the ensuing consequences.

Where to begin?

Working with Indesit equipment is not difficult. The unit is not overloaded with electronics; it does not have large touch panels, color displays or remote control. This makes the machine reliable and easy to use.

Are you unplugging your washing machine?

Oh yes! No

To start washing, you must perform the following steps:

• carefully open the hatch and load dirty things into it in a volume not exceeding the recommended amount;
• place a carefully measured amount of detergent into the tray;
• insert the plug into the socket;
• turn on the power using the general button - “ON/OFF”;
• set the program selector to the desired position;
• use the toggle switch to set the temperature and speed;
• if necessary, adjust the program in accordance with your preferences;
• press the start button.

Washing machine panel "Indesit"