Hotpoint Ariston LST 53977: Instructions and manual in Russian

To ensure comfortable living conditions, a dishwasher is installed. Its purpose is to automate the washing process. The Ariston-Hotpoint dishwasher, the instructions for which can significantly increase the efficiency of the equipment and extend its service life, should be installed exclusively in accordance with the recommendations.

Test run of the dishwasher

So, detergents are loaded into the compartments and all communications are connected. The water valve on the tee that drains water to the PMM is open. All that remains is to press the power button and start setting up the household unit.

Inside the chamber there should be only nets, baskets and other utensils included in the dishwashing kit

The type of detergent and salt consumption have already been set. Switch the dough rinse aid flow rate to the minimum value. With further use, you will select the optimal level of consumption.

The rinse aid consumption is set by moving the arrow (position 1 corresponds to the minimum level)

The setup manipulations are completed by choosing a program that will allow you to wash the camera and all the parts located inside as efficiently as possible. To do this, set the longest wash program with the highest water temperature .

Bosch PMM control panels of different models - built-in and partially built-in

Close the door, launch the program and monitor the status of communications and the speed of work at different stages. If the PMM is working, then:

The water supply runs continuously, the machine does not stop the program;
the liquid is heated over a short period of time;
the spent liquid is completely drained into the sewer;
After the drying process, no moisture remains inside.

How to install and connect

With proper installation and use of PMM, it is possible to extend the service life. Among the main recommendations for installation and connection, the following points can be noted:

The site for installation of the device is carefully prepared. Deviation from vertical placement by more than 2° is not allowed. In this case, it is recommended to insulate the floor surface, which will eliminate the possibility of flooding the neighbors below in the event of a leak.
It is allowed to connect the equipment only to cold water. This is due to the fact that hot water has a large amount of impurities.
When creating a sewer system, the possibility of reverse flow should be eliminated. A special element is installed for this purpose.
Attention is also paid to the electrical part. The socket and electrical cable must be of the correct type. In this case, grounding is carried out to eliminate the possibility of a short circuit.

At the time of installation, the position of the equipment is checked using a building level. When connecting individual pipeline elements, it is recommended to use FUM tape.

How to properly start a dishwasher with dishes

If the test run was successful, the machine is ready for long-term use. We wrote in one of the articles how to load dishes correctly.

Let's look at the requirements for including PMM Gorenje, Whirlpool, Vestel, Zanussi, Hansa along with dishes:

Detergent is added once, before each wash. Rinse aid and salt are enough for several times. The indicators on the control panel will inform you about their completion.
Clean appliances of food residues before loading.
Place dishes at a short distance from each other, otherwise they will not be washed. Large cutlery is located in the lower basket, plates in the middle, cups and glasses in the upper (depending on the configuration of the dishwasher). Many models have glass holders. It is important not to overload the baskets, otherwise some devices will block others, and water will not get to them.

Do not place objects in the tray; the sprayer must rotate freely.
Close the door and select the optimal mode to start working, focusing on the degree of soiling and the type of dishes.
After washing, do not remove items immediately. Let them cool and dry.
Every time, clean the drain filter from food debris and check the spray nozzles.

Follow the instructions carefully. The manufacturer indicates which dishes can and cannot be washed in a machine. Otherwise, you risk damaging the devices.

In one of the articles we wrote that it can be washed in the dishwasher. Briefly about what should not be washed:

Aluminum, wood, tin cutlery.
Products made of non-heat-resistant plastic. Such vessels and plates must have washing instructions.
Porcelain, crystal.
Cast iron, Teflon coating.
Thermoses, thermal mugs.

Users on forums often ask: is it possible to run the dishwasher without salt? It is not advisable to do this, since over time, white spots will appear on the dishes, and the parts will become covered with scale and deteriorate.

Service

Manufacturers recommend periodic maintenance of the device. It takes a little time to clean the filter element and nozzle. The recommendations are as follows:

The filter purifies the water that is supplied to the device during operation. It is recommended to check the filter element after each use. The surface is cleaned using a metal brush or other similar product.
The sprayer needs to be cleaned much less frequently. Food particles can cause rust to form, which will reduce the flow of the nozzle.
Removing dirt from the filter element, which is located on the inlet hose. To do this, it is enough to dismantle the hose, after which you can remove all dirt with a brush.

If the machine operates with a dirty filter, there is a possibility of a malfunction.

How to turn it on

It is easy to turn on the Ariston dishwasher when it is installed correctly. The instructions look like this:

The machine is loading. It is recommended to place fragile dishes in the upper basket.
The next step is to determine the appropriate program. The control panel allows you to select the dose of detergent.
After selecting the program, you can close the door, after a few minutes the washing cycle begins.

If installed according to the manual, there will be no problems turning on the dishwasher.

Malfunctions and their elimination

There are many problems that can cause the device to become unstable. If the machine does not start to function, the reason may be the following:

The water supply tap is closed. If there is no water, the device will not turn on.
Incorrect hose connection. If the installation was not carried out according to the instructions, there is a possibility that water will not flow in the required quantity.
There is no water in the water supply system.
Insufficient water pressure. A similar problem often occurs in country houses that have an autonomous water supply system.
The inlet hose was bent. Incorrect connection of the device may result in the hose being bent during operation and the throughput being reduced.
The filter on the inlet hose is clogged. It is designed to remove contaminants.
The door was not completely closed. If a foreign object gets into the space between the housing and the door, the PMM will not turn on. The device is equipped with a special sensor, which eliminates the possibility of flooding of the room due to poor sealing of the working part.

Most problems can be eliminated on your own, since to do this it is enough to provide the required water pressure and clean the filter element. If the washing procedure is ineffective, you need to pay attention to the following points:

The container does not contain the required amount of detergent.
The washing program was selected incorrectly.
The fine filter is clogged.

There is a possibility of a problem with water drainage. It can be caused by a bent hose, as well as a clogged sewer. A white film may appear on the surface of the dishes if the lid of the special container for storing salt is not tightly closed.

The built-in dishwasher is equipped with a device that can independently detect a malfunction and indicate the corresponding code on the display.

What programs are available to the user?

The memory of modern PMMs contains several modes that differ in duration, water heating temperature, number of rinses, etc. Each model has its own set of programs and additional functions. To figure out what the device can do, you need to look at the user manual.

A full description of the washing programs is presented in the instructions for the PMM.

If you buy a used dishwasher and the user manual is lost, you can look up the information on the Internet by specifying your PMM model in the search bar. Let's figure out what washing modes are available on most Hotpoint-Ariston machines.

The intensive program is designed specifically for heavily soiled cutlery, including pots, pans, and baking trays. This mode cannot be used for washing crystal, porcelain and other delicate dishes. The cycle duration is 145 minutes. Includes pre-soak, main wash, rinsing and drying. The water warms up to 65°C.
Auto. Standard mode designed for washing moderately soiled dishes. This is a normal cycle, optimal for daily running. Assumes drying. The program execution time is 110 minutes. The water temperature during the process reaches 55°C.
Pre-rinse. An additional step before standard washing. There is no need to load cleaning agent into the cuvette. The cycle duration is 8 minutes.
Eco. A mode designed for washing dishes with a medium degree of soiling. The program provides for reduced electricity and water consumption. The cycle includes pre-rinse, main wash, rinsing and drying. The duration of the algorithm is 155 minutes. The maximum water heating temperature is 50°C.
Fast cycle. A short program for washing lightly soiled cutlery immediately after eating. Assumes incomplete loading of the working chamber. Duration – only 25 minutes. Drying of dishes is not provided - after removing the product you will have to wipe it manually. The water is heated to 45°C.
Crystal. Economical, delicate mode, suitable for washing fragile dishes with a low degree of soiling. Ideal for washing crystal and porcelain cutlery. Not available on all Hotpoint-Ariston models. At the end of the cycle, drying is activated. The duration of the program is one and a half hours.
Short Time. A mode designed for washing plates and pots with normal soiling. The duration of the program is 1 hour 20 minutes. Finally, the drying of the dishes is activated.
Ultra Intensive. The most “hard” mode, designed specifically for washing pots, saucepans and baking sheets with dried food residues. The cycle continues for 155 minutes. There is a stage of pre-soaking, main washing, rinsing and drying. The water warms up to 70°C.
Good Night. Optimal mode for starting the car at night. The dishwasher operates almost silently, doing an excellent job of removing dirt. The cycle duration is 3 and a half hours.

Although the Eco program lasts longer than most other modes, it still ensures minimal consumption of kilowatts and water. Consumption is comparable to a fast cycle. Therefore, you should not be afraid of a duration of 2.5 hours.

Most Hotpoint-Ariston dishwashers have modes: “Intensive”, “Eco”, “Fast”, “Auto” and “Pre-rinse”. Other algorithms are found on separate models. Knowing the description of the washing programs, you can accurately select the optimal settings, focusing on the type of dishes and the degree of contamination.