Detailed instructions on how to restart a Kandy washing machine


An error in selecting a program, the need to remove a foreign object from the drum, a malfunction of the control module - this is an incomplete list of problems, the elimination of which requires rebooting the Candy washing machine.

Having carefully studied the information about exactly when and how the reboot is carried out, restoring the normal operation of the washing machine yourself will not be difficult.

We'll tell you how to restart the Kandy washing machine below.

When might it be required?

A reboot will help restore the functionality of a washing machine that has been frozen for some time due to a short-term failure of the control module.

Also, a reboot is simply necessary if:

  • a foreign object has entered the washer drum that can disrupt the normal operation of household appliances (for example, a small metal button or coin can deform the walls of the drum);
  • the washing machine is not loaded enough, which leads to imbalance and strong vibration (reloading the drum can eliminate the problem);
  • The running washing program does not correspond to the type of dirty laundry loaded (it is necessary to change the temperature, the number of spin speeds).

The washing machine signals a malfunction with an error code, deciphering which you can understand exactly what will help restore the operation of the household appliance: repair or reboot.

Is it possible to add powder during washing?

Manufacturer's operating instructions confirm that powder should not be poured into the drum. And the point here is not about maintaining the working condition of the machine, but solely about the quality of washing.

Interesting materials:

How to find out the SNILS of an individual? How to find out the period of the ban on entry into Russia online? How to find out the period of the ban on entry into Russia? How to find out your old Microsoft password? How to find out the amount of pension accrual? How to find out information about an individual's income? How to find out your FPS in CS? How to find out your device ID? How to find out your login and password in Odnoklassniki? How can I find out my travel restrictions?

When should you not reboot?


A reboot can be avoided if more than half an hour has passed since the start of the wash (in such a situation, it is more rational to wait until the end of the wash than to interrupt an almost completed process).

Also, do not rush to reboot if the Kandy washing machine has stopped due to a power outage. Most often, the washing process resumes on its own immediately after power is supplied to the network.

It is not advisable to restart the washing machine often, otherwise there is a high risk of failure of the control module, which entails serious and expensive repairs of household appliances.

Error codes for Kandy washing machines with display (Activa Smart series)

The Activa Smart series is equipped with an information screen, the error code is displayed in the form of letters and numbers. For Kandy washing machines of this type, the following types of errors are possible:

Error E01 indicates that the washing machine cannot lock the door. However, the buttons do not light up. The reason may be a breakdown of the UBL, electronic module, or broken wires. It is necessary to check the components, replace faulty ones, and also inspect the wiring for damage and, if found, restore it.

The appearance of this message on the display indicates problems with the fill. It may not fill at all or partially fills the tank; code E02 is also displayed if more liquid is poured than necessary. The reason for this behavior of the machine may be a malfunction of the water intake valve, electronic board, or pressure switch. There could also be a leak in the liquid level sensor pipes or a blockage in the filter of the water intake system. To eliminate it, you need to check the valve, diagnose the control board and pressure switch. If necessary, faulty components should be replaced. You also need to clean the filter and check the pipes for damage, and then replace them if defects are found.

This error indicates problems with the drain. Liquid discharge into the sewer takes more than 3 minutes or is not discharged at all. The reason may be a faulty pump or its circuit, a broken pressure switch, or a clogged drain system. It is necessary to check the pipes, drain hose, water level sensor and pump. Defective elements must be replaced with new ones.

This code indicates a faulty water fill valve. The liquid is poured in a larger volume than required, this is detected by the pressure switch and sends a signal to the control board. The reason may be a failure of the fill valve or a breakdown of the triac on the electronic controller. You should diagnose the central unit and intake valve, and if a defect is detected, replace the unit.

This error indicates problems with water heating. The reason lies in the breakdown of the heating element, temperature sensor or central board, mode selector motor or electrical circuits. It is necessary to use a multimeter in resistance mode to diagnose faulty elements and circuit links. If a faulty unit is found, replace it.

This code indicates that the motor is spinning too fast. After three attempts to run the program, the machine shuts down. Usually the cause of the malfunction is a failure of the tachometer.

This message indicates that the car's engine has broken down. The shaft stops rotating, the reason may be a burnt-out triac or a breakdown of the control unit. It is necessary to diagnose faulty elements and replace them if necessary.

Algorithm of actions

Depending on what caused the problem that requires a reboot, the process of restoring the functionality of a household appliance follows different algorithms .

To change previously set washing parameters

To restart the washing machine in order to change the washing mode, you must press and hold the “Start/Pause” button for 10 seconds. As soon as the indicators on the control panel blink green and immediately go out, the reboot of the washing machine can be considered complete. The next step is to configure the necessary parameters.

To remove a foreign object from a ram

If the purpose of the restart is to reload or remove a foreign object from the drum, the process follows the following algorithm:

  1. Press the “Start/Pause” button for five to seven seconds.
  2. Wait for the UBL to unlock (a characteristic click indicates that the door lock is unlocked).
  3. Open the hatch, get the necessary things or add dirty laundry to the ram.
  4. Close the hatch and restart the washing process.

This reloading option is possible provided that the washing machine drum has not had time to fill with water.

In the case when the Candy washing machine has already filled with water, the reboot proceeds according to the following algorithm:

  • the washing process is blocked by pressing the “Start/Pause” button;
  • the selector handle is moved to the neutral position;
  • Pressing the “Drain” button starts the process of draining water from the tank.

As soon as the water drains, the hatch door will unlock.

If for some reason it was not possible to automatically drain the water from the washing machine, you can solve the problem manually, through the drain filter. To do this, having previously covered the washing machine with rags, unscrew the drain filter at the bottom of the front panel through which waste water is drained from the tank.

To restore normal operation of the control module

If a reboot is necessary to restore the functionality of a washing machine that is “frozen” after a short-term failure of the control module, the process follows the following algorithm:


  1. Press the “Start/Pause” button for five seconds.

  2. As soon as all the indicators blink green and immediately go out, turn off the washing machine (press the “On/Off” button, disconnect the device from the network).
  3. After twenty minutes, the device is plugged in and the washing process is restarted.

Do not unplug the washing machine from the socket until the “Off” button is pressed. A sudden blockage of the power supply can cause serious malfunctions in the operation of the control module (the electronic board burns out, the replacement of which requires time and financial costs).

sma Candy cs4 1051d1/2-07 Touch control panel buttons do not work

Solution

Comments (5)

Your comment +5

There is a small radiator screwed onto the back panel. I don’t understand what kind of object this is, but it unscrewed and while it was being transported, everything weighed. I took a photo.

Hi. I knew that this forum is serious Thank you for all help from members I want to know the values ​​of these resistances.

By mistake, voltage was applied to the input of heating element J2. The SMA does not turn on, but sometimes when turned on, all the LEDs light up. You can see the smokeiness near the RL200 relay. RL2.

Good afternoon Help me please! Ariston AVSL-109R No. 80297010000. I removed the tank and replaced the bearing. By the way, I have one, not two. N.

Initially, the ubl did not work, the “tablet” burst, - I changed it, took the tab from the Samsung ubl. The hatch began to be blocked, the pump is triggered, on the spin cycle.

Good afternoon Help with the firmware (software + config). AEG L64840L (91454560-00) Firmware WBF20342 Electrolux code: 132670222 Jabil Code: .

How to turn it on after?

In a situation where the Kandy washing machine was rebooted without opening the hatch, then to start a new washing program, just press the “Start/Pause” button.

If during the reloading process you had to drain the water from the drum and open the hatch, then to restart the washing process you must :

  • select the desired mode,
  • adjust the temperature parameters and the number of spin speeds,
  • then press the “Start/Pause” button.

If the restart occurred due to a temporary power outage, then most likely the washing machine will continue washing on its own according to the previously set program after the power supply is restored.

If this does not happen, the washing mode and all the necessary additional options will have to be set manually by pressing the corresponding buttons or turning the selector knob.

Page 12

Press the START/PAUSE

to start the selected wash cycle.

Once the program is selected, the switch

position until the end of the cycle.

by turning the program selector switch to the OFF position.

.

Click to start the selected cycle.

LAUNDRY AFTER STARTING THE PROGRAM (PAUSE)

Press and hold START/PAUSE

approximately
2 seconds
(the light indicator and the time until the end of the wash will start flashing, indicating

paused).

Wait 2 minutes,

until the security system unlocks the door.

After adding or removing items, close the door and press the START/PAUSE

(the program will start from the moment it was interrupted).

To cancel a program, set the program selection switch to OFF.

.

This button allows you to delay the start of the selected wash cycle for up to 24 hours

.

A special safety device prevents the door from opening immediately after the end of the wash cycle. Before

end of the wash cycle (should go out

Program selection switch with OFF position

After turning the selection switch

display showing settings for the selected program. To save energy, the display brightness is dimmed at the end of the wash cycle and when the machine is not running.

IMPORTANT: To turn off the machine, set the program selection switch

The program selection switch must be returned to the OFF position at the end of each wash cycle, or when starting a subsequent wash cycle, before selecting and starting the next program.

Close the door before pressing the START/PAUSE button.

After pressing the START/PAUSE button, it may take a few seconds before the machine starts to operate.

To avoid overflowing, make sure that the water level is below the door opening before opening the door.

Source

If rebooting doesn't help

A situation where a reboot does not help restore the interrupted washing process requires careful diagnostics and repair of the washing machine. Most often, the cause of problems is related to the electronics and control module.

The washing machine indicates a malfunction with a specific error code on the control panel display or by flashing indicators. Knowledge of the Candy washing machine will help you solve the problem yourself, otherwise you cannot do without the help of service center professionals.

Calling a master: what do you need to know?

If you cannot solve the problem with a non-working Candy washing machine on your own, you should call a specialist. To do this, you should contact a company that repairs washing equipment and has been working on the market for several years.

You can find such a company on the Internet. There will also be reviews about the work of the masters and contact information. Calling a specialist from such a company will help you avoid falling for scammers.

The cost of repairs depends on the company’s pricing policy and the complexity of the repair work. For the capital, average prices are as follows:

  • replacement of the electrical wiring harness - about 2000 rubles;
  • repair of the control module – from 2000 rubles;
  • replacement of the hatch blocking device – from 1,500 rubles;
  • Replacing the washing machine power button – from 1000 rubles.

After the repair is completed, the technician performs a test run of the washing machine and issues a guarantee for the work he has done. If new parts were needed to restore functionality, their cost will be paid separately.

Checking the tachometer and engine

Unfortunately, the attached instructions do not include a detailed description of error E08. It only contains information that it occurs when the motor tachogenerator breaks or when it shorts out. It can also occur when the engine fails, and less often when the control module breaks down. Based on the information provided, first of all you should check the functionality of the following parts:

  • motor;
  • tachometer;
  • control module.

Verification requires compliance with a certain algorithm. At the first stage, the motor with the tachogenerator is removed, and then the following steps follow:

  • disconnecting the machine from power;
  • removing screws from the rear panel;
  • dismantling the panel itself;
  • removing the drive belt while simultaneously pulling it towards yourself and turning the pulley.

Then you should remove the engine. To do this, it is recommended to put marks on the wires coming from the motor in order to prevent difficulties during connection. Then we unscrew the bolts that hold the engine and remove the latter from the housing. Now we inspect the Hall sensor in the machine: strong vibrations could lead to loosening of the fastening or loosening of the contacts. In such a situation, you only need to tighten the mounting bolts and restore the connections.

If this is not the problem, you will need to check the resistance of the tachometer. There are two methods for this.

  1. Setting the tester to resistance determination mode. It is necessary to release the wire connectors and remove them from the sensor contacts. Then the probes are adjusted to the contacts to check the resistance. The normal range is considered to be from 60 to 70 ohms.
  2. Switching the tester to voltage detection mode to understand whether current is being generated or not. To check, probes are applied to the sensor contacts while the engine is cranked. If the values ​​change (approximately 0.2 Volts), then the part is in working condition.

It is imperative to check the wiring for integrity, because Often it is this that leads to breakdown of the tachogenerator. And if the part is in a faulty condition, it will need to be repaired or completely replaced.

If the breakdown has not yet been identified, you should start checking the motor. At the starting stage, we check the brushes, and if it turns out that they are worn out, we replace them.

So, using a multimeter, we check the wiring supplying the tachometer and the motor for breakdown. If no breaks are found, you will need to check the rotor and stator resistance. Then we check whether there is a current leakage to the housing, followed by testing the turn-to-turn short circuit in the winding. A breakdown means that the engine cannot be repaired due to the high cost of repairs, and the best option would be to install a new engine.

Individual approach

Despite the existence of general rules for resetting washing machine programs, representatives of each brand have their own special cases.

On older Ariston and Beko models, there are no buttons to start washing at all. This action is carried out by turning the program selection knob. To reset, you need to set it to neutral, then hold the off button and turn the washing machine back on after 30 seconds. How to do this correctly is shown in the video.

The same situation is with older analogues of Elgie. Modern LG and Samsung models are equipped with a special program reset button, which can be used at any stage of the wash. She will stop the process on her own, drain the remaining water and then open the hatch.

Elgie washing machine

Resetting the program of the Indesit washing machine can be done using the button above which there is a diamond with a vertical line in the center. If it is not on the control panel, then simply turn the programmer to the neutral position.

Washing machine Indesit

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]