How to fix a zipper on jeans

If fabric or threads are stuck in the zipper

Lining or threads being chewed is the most common cause of fastening mechanism failure. This kind of trouble can happen if the zipper on your jeans is fastened in a hurry or jerkily. You can release stuck material by gently pulling the slider in one direction or the other. To troubleshoot the problem, it is important to be patient and avoid sudden movements. Most often, the lining becomes the “victim” of the dog. When fastening multi-layered items, you should be especially careful and adjust the fabric with your fingers when moving the slider up the links of the snake.

Source:

The teeth have fallen out of the zipper - how to repair it?

How to fix a lock on jeans if it has “lost” several teeth? Please note that this failure is serious and requires replacement of the mechanism.

But if you have enough patience, we suggest trying to repair the zipper so as not to rip out the entire lock and sew in a new one. For this:

You need to buy a lock with suitable teeth in thickness and height.
Remove the required number of teeth from it. For “tractor” locks, they are usually easy to remove.
To transfer the clove to the zipper, take a piece of copper foil.
Then open the clove that needs to be secured to the lock, place it first on a strip of foil, and then move it to the fabric.
Install subsequent ones using the same technology.

You can secure the result using stitches between the “new” teeth. The castle is ready for use again!

The castle diverges

The only thing that needs to be replaced is the fastener on the jeans, which suddenly came apart. If this is not possible, then you can do the following: Insert an elastic band for money into the tongue of the carriage and hook it to the button after fastening it. The zipper on jeans can be temporarily fixed using a stapler or paper clip. When you have pliers or another similar tool at hand, you need to pinch the edges of the slider on both sides. A weak carriage is most often the reason why the zipper keeps coming undone.

Lightning parted in the middle

How to make a zipper on jeans if it has spread out in the middle? Such a mechanism definitely needs to be replaced, but if we are talking about repairs as a temporary measure, try connecting the lock teeth with your hands when fastening it. Then press the zipper with pliers to be sure. This tip will help you out if you are late and have no time to change clothes.

Important! If you sometimes have problems with different fasteners, also learn about how to install snaps on clothes.

The zipper slider is broken

You can fix a fly with a broken slider by replacing the latter with a working one from an unnecessary fastener. If you don't have a spare element on hand, you should get creative and use a paper clip, soft metal wire, etc. In order to choose a suitable size “dog”, you should pay attention to the back side of the slider. The number corresponding to the size of the product must be stamped on the bottom side. All that remains is to find a working element with the same number and replace the broken one with it.

What material should the rivet be made of?

Rivets are usually taken from the same material as the parts being connected - this avoids electrochemical corrosion.
Pay attention to the strength characteristics. But, as a rule, when connecting aluminum parts, the strength of aluminum hardware is sufficient

In general, rivets are made from the following metals:

steel:

regular - brands St2, St3, St10;
corrosion-resistant X18N9T;
galvanized;

When connecting copper parts, it is permissible to install brass and copper. Aluminum is joined with aluminum alloys. Steel sheets - corresponding grades of steel rivets. There are also mixed hardware - from two different metals (chemically non-conflicting). The most common are aluminum-steel.

To install facade elements, slopes, ebbs, metal tiles and corrugated sheets, rivets made of galvanized painted steel are usually used. Painting - matching with details.

The rivet is an excellent and durable type of fastener. But unlike bolts, nuts, studs and screws, it cannot be removed without damaging it. The bolt can be unscrewed with keys or a screwdriver, after which it can be reused. The broken rivet will have to be thrown away. The question also arises: “How to rivet rivets if there is no riveter in your arsenal?”

The zipper on my jeans keeps coming undone

0
Source:

If the zipper on your trousers constantly comes apart, for example, when bending or squatting, a simple design made from improvised means will help you avoid the inconvenience. A small metal ring or twisted piece of soft wire should be attached to the pawl and placed over the button in the fastened position. This solution to the problem is temporary, but will protect you from awkward situations for a while. Often the reason for the sudden opening of the zipper is excessive tension in the fabric at the zipper fastening point, when the jeans are small or too tight.

Who invented jeans with a fly at the back?

How to repair different parts of a zipper with your own hands and the necessary tools
Jeans with a fly at the back were invented by a native of Georgia, creative director of the Balenciaga fashion house, founder of the Vetements brand, one of the leading designers of our time - Demna Gvasalia.

Today, this extraordinary and talented person has a lot of interesting things behind him. The brand, founded together with his brother, has become the most talked-about phenomenon in the fashion world in just a few months.

Floral dresses and reconstructed retro items from Vetements are a 100% must-have for every fashionista.
It was Demna who dressed the younger generation in a unisex hoodie with Titanic prints and Triple-S sneakers.
And here is another explosion - pants with a fly at the “fifth point”! They were the result of joint “creativity” between Vetements and the world famous denim clothing manufacturer Levi's.

These pants are called Vetements x Levi's Back Zipper Jeans. They are very reminiscent of cowboy pants, made of several panels of thick denim. In addition to the fly at the buttocks, they have unbuttoned knees and pant legs in the back along the entire length of the legs.

The zipper teeth are damaged

When it is impossible to unfasten a zipper due to damaged teeth, the only salvation is to replace the zipper. For short-term use, you can apply a few stitches to the area just above the break. After this, the carriage will only lower to the bartack, but will retain its function. To replace a zipper that cannot be repaired, do the following: Open the bottom of the zipper using a special sewing tool or nail scissors. Spread the side rivets and release the edges of the lock from the stopper. Release the side parts from the stitching and remove the entire zipper. Using a sewing machine, sew a new design in place of the old one, using matching threads. Recommendations for preventive maintenance will help maintain the functionality of the new lock.

How to care for zipper: prevention tips

It is easier to prevent a breakdown than to look for non-standard solutions to the problem later. Proper operation and preventive maintenance of the fastener can significantly increase its service life.

Follow these guidelines:

A damaged zipper on your trousers is not a reason to throw away your favorite item. In most cases, the breakdown can be repaired with improvised means or the functionality of the zipper can be temporarily preserved.

Problem 5 – replacing the zipper

And the most difficult problem that can arise when using a zipper is completely replacing the fastener. In these cases, you have to rip out your clothes, and not everyone can do this at home. It is especially difficult for those who have other elements, such as buttons, next to the zipper. We want to show you how you can replace your zipper without blowing it out.

Cut off the zipper on the side where the buttons are closest to the edge.
Baste, and then sew one half of the zipper on this side with two lines. Its edge should be close to the buttons, without going over them, so as not to interfere with their fastening.
On the opposite side, simply sew the new zipper onto the old part without cutting it off. Photo 3 shows the view from the reverse side.
This is what the finished work looks like.

What life hacks for zipper repair do you use?

What to do if there are not enough teeth?

The lack of teeth is one of the reasons for the inconvenience when fastening. Over time, they fall out, leaving behind gaps that impede the passage of the slider.

We close the gaps on the plastic zipper:

We buy thick fishing line.
We drag it to the place where the tooth fell out.
We wind it several times so that the size matches the rest of the teeth.
We secure it with a lighter, after making a small knot.

This method will help make fastening easier, postponing a visit to the studio.

A metal zipper can only be repaired using similar teeth. They can be found on an old zipper that is no longer used.

It is important that the size of the teeth correspond to those available, otherwise the procedure will not be beneficial. Insert the teeth into the metal zipper:

Insert the teeth into the metal zipper:

We separate the required number of teeth of a suitable size from the old zipper.
We put them in place of the spaces and clamp them with pliers.
Check the strength and re-tighten if necessary.

Important! It happens that the teeth do not fall out completely, but begin to interfere with the normal passage of the slider. The lock is opened and placed on a hard surface, after which it is lightly tapped with a hammer on the teeth

The lock is opened and placed on a hard surface, after which it is lightly tapped with a hammer on the teeth.

This should bring them back to their original position. This method only works on metal zippers!

How to restore damaged

If the metal button has stopped performing its function and is constantly coming undone, a regular hammer can help.

To do this, the convex part of the fastener is placed on a hard surface and blows are carefully applied, slightly flattening the “bump”. After each blow, you must try to fasten it. Once the fixation is secure, the goal is achieved.

Once the fixation is secure, the goal is achieved.

The plastic fastener can be repaired using an iron, tracing paper or foil. To do this, cover the convex part with foil or tracing paper and melt it a little. After the plastic hardens, try to fasten it. You can correct the melted edges of the button using a nail file.

How to quickly repair a metal zipper if it comes apart or the slider has fallen off?

A metal zipper is considered the most reliable and durable, since its teeth (brass or nickel) are located on a fairly dense material and are connected to each other especially firmly.

However, it also has a number of disadvantages:

scratches fingers
The slider often jams
teeth cling to fabric threads

In order to repair a broken fastener, you first need to determine the cause of the breakdown. In the case where the slider is to blame, you can make a quick repair like this:

prepare thin pliers (pliers) or non-sharp tongs
carefully examine the slider to determine the location of voids and partitions inside it
Using pliers, carefully press both sides of the pawl onto the fastener links
do it from top and bottom
fasten the zipper
squeeze the base of the slider slightly towards the center
do not overdo it, press lightly so as not to break the lock or make it too tight

Sometimes a metal zipper begins to diverge due to deformation of the links. At the initial stage, it is easy to correct the situation:

lay the item on a hard surface
lightly tap along the entire length with a hammer
do this from the outside and inside
walk this way several times

If the “snake” diverges in only one place, this means that the teeth in this area are especially damaged. You can fix it like this:

fasten the zipper
in the area where the links diverge, connect them with your hands
Using light pressure with pliers, align the problematic teeth

Repairing a zipper
In the case where the links are damaged or missing at the bottom of the “snake”, you can proceed as follows:

on a permanent one, make a few stitches over the missing teeth. In this case, the fastener will only unfasten to this sewn area. Check whether this length is enough for you to use comfortably.
on a detachable one - change the lower limiter on which the slider rests. To do this, remove it, helping yourself with pliers. Replace it with a stopper that is larger in size. It will cover the hole from the missing link.

Sometimes the dog flies off the zipper and it becomes impossible to use the item. This problem is also completely fixable.

When the slider has completely fallen off:

slightly support the seam with which the fastener is sewn to the product
pull out the ends on one side
Using tweezers, an awl or small scissors, open the clamps at the top or bottom of the zipper (whichever is more convenient) and remove them from the fabric base
pass the ends of the ribbon inside the runner
push it a little along the zipper
put the latches back in their original place

When the slider has flown off only one side:

from the edge that is not attached to the tape, slightly open the slider with tongs to increase the gap between its walls
lower it down
carefully insert the teeth of the fastener into the slider
make sure that they are positioned evenly, without tension or bending
lightly press the edges of the slider
in the case when it is impossible to unclench the walls of the “dog”:
remove the stopper on one side of the fastener
put on the doggie
put the limiter back

If the slider is broken and cannot be replaced, it must be replaced. When purchasing a new one, keep in mind that its shape and size must match the configuration of the fastener. On the reverse side of the “dog” the dimensions are indicated in millimeters. If the lock is lost, it is better to take the zipper with you to the store to avoid making the wrong purchase.

Repair metal zipper

Please note that inserting the slider onto the “snake” will be much easier if you lubricate it first:

vegetable oil
paraffin candles
unsalted lard
toilet soap

Use literally a drop of the chosen product so as not to clog the slider and links, and also not to stain the product.

Helpful tips if the zipper comes undone

If the slider still won't hold despite your efforts, try rubbing the teeth themselves with something that will increase grip. Rosin is well suited for this - musicians and dancers use it to prevent the surface from slipping. Lubricate the zipper with an alcoholic infusion of rosin inside and out and let it dry for a couple of hours in an unzipped state - now the pawl will not slip down so easily.

When all else fails, the lock can be fixed in the desired position by hooking it on top with a tongue on something. Sew a clothes hook to the fabric edge of the zipper and hang the slider on it.

As a last resort, you can try replacing the zipper at home with a new one. To do this, you will need, in fact, a new zipper, a spool of shoe nylon or strong thread, a thick needle, and it is advisable to also take a thimble and pliers to make your work easier:

Carefully unscrew the old zipper; Cut the new one to the required length, shorten it from the bottom to the iron staples; Place the zipper on the boot and secure it with pins; Sew by sticking thread into existing holes, helping yourself with pliers.

Well, now your boot is in perfect order, and nothing should interfere with your walk.

Subscribe to our Social networks

How to squeeze a dog

It seems that what could be difficult when clamping a slider? But you can easily and simply not calculate your strength and break a small engine.

In this case, there is only one way out - replacing the zipper or slider. For repairs you will need pliers or pliers, as well as a hammer.

Follow the step-by-step instructions:

Fasten the lock and slide it a few centimeters from the base. The zipper must be closed during repairs.
Pinch the top of the slider with pliers. Carry out the operation from the side of the closed lock.
Take a hammer in your hands and strike the pliers lightly. If necessary, you can repeat the procedure.

Important! This method is suitable for repairing a lock on any item: from boots to a jacket.

This repair is considered the safest and will definitely not damage the slider. You can simply fix the lock with pliers, but you should carefully calculate your strength so that the dog does not crumble.

To prevent the lightning from running away and the hammer blows from hitting your fingers or simply along the length of the zipper, you need to fix the product on a table or stool.

How to remove rivets from jeans

Preparation and use of garden varnish: what can replace it

Rivets and buttons on jeans are disposable items. Is it possible to give them a second life?

I was planning to knit a rug from old jeans. I collected a bunch of pictures online, information on how to cut fabric, how to knit, etc., etc.

I've collected some jeans. It was cut and even began to knit. So far I really like the process and am happy with the result, although the rug still looks like a very narrow strip.

But even at the very beginning of knitting it became obvious that as a result there would be a lot of removed rivets and buttons.

I also collect scraps and threads to stuff sewn bears (dreams, dreams).

I haven’t figured out what to do with the rivets yet. Where would we then put this pile of pieces of iron?

Can you recommend anything?

Well, a few rugs so that the post is not boring

My rug is thinner and more transparent.

source

—Quote book

Square bag. It is better to sew bags using the so-called stitch, that is, using a sewing machine with high stitching.

We are sewing a new backpack from old jeans. I have accumulated a number of leftover ones.

Super potatoes in 5 minutes! Brilliant potato recipe! Just 5-10 minutes of preparation.

We sew our own toiletry case We sew our own toiletry case

The clasp has come loose...

And, as luck would have it, you don’t have a single minute of free time. How to repair a zipper on boots in literally seconds?

Using pliers, lightly squeeze the “slider” of the lock. After this it should work stably.
If this does not help, lightly tap the “snake” with a hammer on the outside and inside.
If spontaneous unfastening of the lock occurs constantly and does not depend on how carefully you put on your shoes, an alcohol solution of rosin will help. Unfasten the clasp and apply the solution to both halves. Leave the zipper to dry for a couple of hours, then test it for functionality. If the result is not entirely satisfactory, repeat the procedure again.

Problem 3 – the edge of the zipper is frayed

Sometimes such a nuisance as a frayed edge of a zipper happens. And the problem is not only that it looks unaesthetic. In such a situation, fastening the zipper becomes more and more difficult every day. And if measures are not taken in time, the fastener will have to be completely replaced. And the solution is quite simple. As soon as you notice that the fabric at the edge of the zipper has begun to fray, carefully coat this area with epoxy glue. When the glue is completely dry, it will toughen the fabric and prevent it from further deterioration.

Free legal assistance

// The lock on the boot is broken Skip to content Javascript Disabled Detected Please enable JavaScript.

After all, if lard gets on the fabric, greasy stains may remain. Rub the teeth with a piece of lard. Excess fat is removed with a dry cloth. Camphor. Simply use a pipette to apply camphor oil to the cloves and distribute it with a napkin.

We bought sneakers for our daughter on Monday evening. August 31st, that is. Fastened with a zipper and drawstring. Last night the lock on one of my shoes started coming undone. Today the lightning started to spread on both of them. My husband tried to fix it and a dog fell off on one side of one of the sneakers... We wore it for a total of 8 hours (approximately).

They cost 1200. I paid by bank transfer….

My husband says go figure it out and let them return the money. Like a 2 week guarantee. receipt, box, bags, shoes themselves in stock.

But I’ve never encountered anything like this, and in general in these matters, I’m a rather timid person. What to do if they don't want to return it? How should you behave? Popular answer After the transfer - regimen, well-being, discharge, etc. zipun, tell me, did you take progesterone yourself or was it prescribed by a doctor?

I have a transfer planned tomorrow, and m... Ovarian wasting syndrome.