Samsung diamond 6 kg instructions for use. Recommendations for operation and settings of Samsung Diamond washing machines

_____________________________________________________________________________

This morning there was a problem. The WF8590NLW8DYLP washing machine cannot open. The door is probably locked. For what reason could this happen?

Apparently, there is a breakdown of the UBL.

Can anyone tell me why the drum is not spinning? The SMA has been in operation for only 7 months.

The main factor for this malfunction is wear on the drive belt or motor brushes.

The WF8590NMW9 machine is connected. The malfunction is that the unit began to shake very strongly. How can I fix this?

If no defects were made during installation of the device, then the shock absorbers or shock absorber springs should be considered a malfunction.

Recently, in the Samsung Diamond WF8590NLW9 machine, the execution time for each stage has begun to increase, so in general, washing lasts longer, however, without loss of quality. It simply erases any program for about half an hour longer, and at the same time does not show anything on the control panel about failures or problems with the equipment.

The timer appears to be faulty.

We bought the WF 8590NMW9 automatic machine about five years ago, almost new. During all this time, it always worked properly and never produced a single failure. Now the unit does not finish washing as expected; during the spin cycle, approximately in the middle of the cycle, it stops with indications of equipment malfunction. Failure indicator LEDs light up on the control panel, and the equipment goes into standby mode. SMA can be restarted only after an hour, not earlier. What is the problem?

There may be a problem with the motor, in particular its windings. You can also check the tachogenerator.

Recently, the drum of the Samsung Diamond WF8590NMW8 machine has not worked in any wash, including when spinning clothes separately. After starting, the device draws water into the tank, then heats it to the set temperature, after which it turns off the program, displays an error and goes into standby mode. The operation of the electric motor is not heard. It is completely impossible to use the device. Help, how to fix the damage?

There may be a problem with the motor, it needs to be diagnosed.

After the last wash, the hatch of the WF8590NLW8DYLP machine did not open, which caused forced intervention to remove the washed clothes. Currently, the device does not start after programming because the door latch does not work. You can select programs, but after starting the unit after a while shows an error on the panel and turns off. What could be wrong?

You need to check the UBL unit. Most likely the cause of the problem is a jammed latch of the automatic door locking device.

At the main stage of washing, the Samsung Diamond WF 8590NMW9 machine works well, but during rinsing it already begins to slow down; the drum sometimes cannot start working for several minutes. Then the water is drained, and already during the spin cycle the drum does not start at all. You need to turn off the equipment, then wait for some time, usually more than an hour, to start spinning clothes that have already been washed in a separate program. All the time the failure occurs, the failure of the devices is displayed, but upon a new start there is no indication on the control panel. What kind of breakdown is this?

It looks very much like a problem in the electric motor; apparently, it has already exhausted its service life due to constant intensive use without preventive maintenance. The engine needs to be checked.

For several days in a row, the WF8590NLW9 SMA has been knocking and vibrating loudly when spinning. The program is carried out to completion, there are no failures. It is inconvenient to use the equipment; with this malfunction in the operation of the equipment, the quality of washing is not affected, but the device moves along the floor covering with the risk of disrupting the connection to utility networks.

There is a problem with the functionality of the electric motor, but the main reason is severe wear of the bearing unit. Bearings need to be replaced.

The Samsung Diamond WF8590NMW8 washing machine does not spin the washed clothes when performing any washing program, so the user has to spin the clothes manually. After completing the rinse cycle, it drains the water and stops, going into standby mode. Several LEDs on the display panel light up to indicate a technical error. Then the device turns off spontaneously. Repeated launches of the program do not give anything. What could be the problem?

It is necessary to check the condition of the drain system, as well as filters and valves for blockages. The sump pump may be faulty.

When draining water during the spin cycle, the WF8590NLW8DYLP equipment works unstably, periodically stops, and an electronic malfunction is always displayed. After being idle for a few minutes, the device resumes operation again, the display goes out, and the spin cycle continues. There is no point in restarting the equipment; the situation does not change. However, having finished spinning, it stops the program, and there are no comments on the quality of the laundry at the exit. What's wrong?

This may be an electronic problem, but there may also be a defect in the drain pump.

In operation, SMA WF8590NMW9 with a load of 6 kg. The problem is that the car did not start the engine, after checking everything that was being done in this case, I began to inspect the module, found a broken ULH 2003, a visible breakdown opposite the 11 leg and between 11 and 9 shorts, changed the microcircuit, to no avail. Then I discovered that there was no power to the engine relay, and the microcircuit was broken again between 11 and 9. I checked on the new one there is resistance between 11 and 9, the relay is working.

Maybe 10 Ohms, or maybe 10 mOhms - where are the numbers? If ULH is faulty, look for a short in its circuit.

Malfunction of the Samsung Diamant WF8590NMW8 automatic washing machine (5 kg load). It constantly fills with water, what should I do, where should I start? The program turns on normally, closes the door, draws water, into the first chamber, then into the second chamber, the drum rotates. The pause button does not respond, it continues to draw water until you disconnect it from the network.

Either change the module, or contact a specialist, but first, it’s still a good idea to check the valves.

The WF8590NLW9 washing machine cannot fill the tank with water when pumping. After one minute of operation, the drain turns on, although the tank is not yet full to normal. An error message appears on the control display. This is the first time the equipment has broken down, although it has been in use for a long time.

Apparently the control module has failed.

Samsung Diamond WF8590NMW9 washing machine installed. When you turn on any washing mode, it shows the DE error. I threw in another module - everything works. Can you tell me what to solder on the module?

Remove the module, look, sometimes you can see it. Check UBL.

In the WF8590NMW8 model, during spinning, the drum rotation speed does not develop sufficiently for high-quality spinning. The SMA constantly spins at a speed of no more than 500 rpm. Which has a qualitative impact on the results. Even if you specifically set 1000 revolutions, it will still work poorly, not giving a high drum speed. You have to either wring out the laundry manually or run an additional spin, which is inconvenient. Tell me, what is the problem?

This problem is most likely in the tachogenerator. Either repair or replace.

The Samsung Diamond WF8590NLW8DYLP machine, when pouring water into the tank, does not take all the powder from the loading tray; almost half of the normal portion remains in the tray. In this case, the equipment does not identify the malfunction and does not show the error on the control panel. Washing has deteriorated, the quality of the laundry does not meet the requirements. How can I fix this?

It looks like the filter screen on the inlet is clogged. Remove the blockage and clean the pipe and tray.

SMA Samsung Diamond WF8590NLW9. Everything seems fine so far, you can close your eyes to something, but as I read about another model, it takes up very little water when washing and rinsing. If you load up to 2 kg. laundry, then even less, if more than 4, then it just spins the wet laundry and that’s it, when rinsing it’s the same. Tell me what can be done or how to deceive her, maybe change her brains or, in general, I don’t know? Any sensible advice will be welcome. I'm tired of adding water to the powder compartment.

Large loads are only possible with the cotton program. For all others, no more than 1.5-3 kg, usually as described in the instructions. An entry-level washing machine, you can’t wait much. Reflash your brains? Well, that's unlikely. Try adding pre-soaked laundry. Maybe this will help.

Malfunction of the WF8590NMW9 washing machine with a load of 6 kg. Doesn't turn on. The washing completed normally with all functions performed and signaled the end. The laundry was not removed for about an hour. After an hour (approximately), the laundry was taken out and the loading hatch door was left for airing. The washing machine was not disconnected from the network. The next day, they loaded the laundry into the drum and closed the door. We pressed the “Enable” button, that is, everything is as usual, no reaction: no indication and silence. The power supply at the output of the network filter (interference suppressor) 220 is available. Electronic unit DC92-00523A/110818/ALF0185, visually (removed, disassembled) in perfect condition (no signs of moisture, scorching, swelling or swelling, and visually without anything that could indicate a malfunction. The “Start” button rang - works without sticking). The hatch locking device was visually like new, it was removed and when 220 was applied to contacts 3 and 5 it was activated to lock. With the connectors removed, both taps/water injection relays were checked for functionality by supplying AC 220 directly from the network - they are operational. What do you recommend checking yourself?

Check the power supply, capacitors, PWM controller, transformer.

We are repairing the WF8590NMW8 washing machine (5 kg load). The DE error appears on the display, although 220 is supplied to the lock itself (checked). The most interesting thing is that I decided to test the lock on another SMA, and it worked. Has anyone encountered such a breakdown? I know that you can climb in the module, but the supply still goes to the lock.

If power is supplied to the lock, then it should close and, most likely, power comes from it to the module if everything is in order with the wiring. Therefore, look for the cause in the module.

After collecting water, the SMA Samsung Diamond WF8590NLW8DYLP immediately turns on the water pump, and the water along with the detergent is removed from the tank. After that she stops and stands waiting. All attempts to restart the equipment end in the same way. Washing is not possible. Help solve the problem.

The water level sensor in the tank is probably faulty. It needs to be replaced.

The WF 8590 NMW9 washing machine is in operation with a load of 6 kg. The reason is this: when washing and spinning, it only turns in one direction. The belt is tight.

Check the motor control circuits (from the motor connector to the processor).

A problem arose in the WF8590NMW8 washing machine after it had not worked for almost six months and was in a dry storage room. After connecting it to the water supply system, the water drainage system and the electrical network, it does not turn on, while only the “Start” indicator lights up, no errors are displayed. For some reason, the water drain pump starts for a while after pressing “Start”. What could it be?

There is probably a malfunction of the pressure switch, in which the air outlet tube may be clogged with salts deposited over time.

10 11 12

In this review, I want to look at the best Samsung washing machines. Let's get acquainted with their characteristics, find out how much they cost, consider their positive and negative sides. We will select the optimal models in terms of price/quality ratio.

The Samsung washing machine is a home appliance produced by a world-class corporation. Using the most advanced technologies in production, Samsung presents devices with new capabilities in elegant design solutions to consumers.

Features of Samsung washing machines

The latest Samsung washing machines feature the Eco Bubble system. The built-in generator produces air bubbles. The detergent dissolves well and turns into foam. The dispersed mass, saturated with oxygen, penetrates into the deep layers of tissue, completely ridding the laundry of contaminants.

Digital inverter technology ensures uninterrupted and reliable operation of the motor through powerful magnets. By eliminating friction, silent operation of the unit is achieved.

The intensive soaking function helps to cope with the most stubborn stains.

Samsung's unprecedented promotion is a 10-year warranty on motors in cars with the Eco Bubble system.

How to choose

Most models of Samsung washing machines are equipped with a lot of useful functions that the average consumer will call unexpected, but very useful in practice.

The Add Wash function is needed for forgetful housewives. When the wash cycle has already started, but another dirty item or sock is found, it is easy to throw them into the already spinning drum. And also add hand-washed clothes for rinsing and spinning.

Modern Smart functions allow you to control the washing process remotely through an application downloaded to your phone. You can start or stop the cycle, adjust the washing time, and receive notifications about the end of the process.

The Smart Check function helps diagnose unit operating errors. Through the mobile application, the user receives a complete decoding of the codes and possible solutions.

The VRT plus technology allows you to make the machine virtually silent even when working at night. It dampens noise and vibration to a minimum level.

Full-size models can hold up to 14 kg of laundry using a spin speed of 1400 rpm. The special structure of the inner surface of the drum preserves the appearance of the products and protects them from creasing and creasing.

Department No. 1

Each powder receptacle compartment in a Samsung washing machine is labeled. As a rule, the compartment with the Roman numeral I is intended for prewash. Therefore, not all housewives use it constantly, but only if washing with soaking is necessary. Therefore, you need to fill the compartment with powder if you have selected a program with pre-wash.

Liquid powder can be poured into this compartment of the tray, but only if it has a plastic partition that will retain the product in the compartment. If there is no partition or grooves for its installation, then you need to pour the gel directly into the drum of the washing machine, but only before adding laundry, so that it has time to drain. But remember that during the main stage, in the middle of the wash cycle, you need to open the powder receptacle and fill compartment II with liquid powder.

Important! If the machine included a special dispenser for liquid products (a small plastic container resembling a ball or a cup with holes), then the liquid powder should be poured exclusively into it. Place the prepared container in the drum along with the laundry.

When the repair site, equipment and washing machine are prepared, you can begin to work.

Article on the topic: Why the Electrolux washing machine does not turn on

The first step is to remove the top panel of the machine. On the back side of the unit, in the upper corners, there are two self-tapping screws on which the panel is attached. Unscrew them with a screwdriver (or screwdriver), lift the back of the cover, move it towards you and remove the panel.

Then you need to remove the detergent tray . To do this, press the locking clip and pull out the container in the same way as you do for cleaning. Behind the powder tray there are fasteners that hold the control panel; By removing the tray, you can easily unscrew the bolts and disconnect the latches that secure it (usually one fastener is located under the tray and two more on the back of the panel). Carefully disconnect the control panel so as not to damage the wires leading from it into the mechanism. To prevent the part from interfering with further work, it is hung from the right side of the unit using a special hook or simply carefully placed on the top of the machine.

When disassembling the washing machine, carefully inspect all parts for damage. For example, quite often the water level sensor fails. It is easy to access the part if you remove the top cover of the unit: the sensor is located, as a rule, on the side wall of the machine, closer to the top, and is secured with 1-2 bolts. Unscrew the fasteners, disconnect the hose and contacts from the pressure switch (the hose is held in place with a clamp that needs to be unscrewed or pulled apart with pliers) and inspect them. If necessary, clean the contacts and remove blockages in the tube, and check the sensor itself with a multimeter.

Next you should remove the hatch cuff . Gently pry the rubber collar clamp (retaining ring) with a flathead screwdriver, pull lightly on it, and then move the screwdriver around the entire circle to release the ring. Remove the rubber cuff and place it in the drum. Proceed as carefully as possible so as not to damage the integrity of the rubber. Close the drum door tightly.

Article on the topic: How to use a Mara washing machine

Next, proceed to dismantling the bottom panel . In Samsung washing machines it is fixed with latches that need to be disconnected from the body. On newer models, the panel is secured with screws; They are easy to find and unscrew.

It's time to dismantle the front wall. How to remove the front panel of a Samsung washing machine? This is quite simple to do: you need to unscrew the screws that secure the front panel to the body of the car (they are located in the upper and lower corners, under the dashboard and above the lower panels). Next, you need to remove the front wall along with the loading hatch from the hooks/latches. First disconnect the wires of the locking lock.

Removing the back panel is even easier: unscrew the four screws and remove the part. Immediately disconnect all hoses that are attached to the machine tank: filler, drain, as well as from the pressure switch and powder tray.

Now you should disconnect the wires of the heating element and temperature sensor or, if necessary, completely remove the tubular heater (for replacement). It is usually located in the lower front part of the tank under the drum. Unscrew the nuts and remove the heating element from the socket. At this point you should also disconnect the motor wires and wiring. Be sure to take a photo of the pin locations so you can connect them correctly when reassembling. The terminals can be marked with colored markers.

To get to the tank, you will have to remove the counterweights (balance stones); they are located at the top and bottom of the washing machine. Unscrew the mounting bolts and carefully remove the weights (they are quite heavy). When performing this work, an electric impact wrench will be useful, which will significantly speed up the process of removing fasteners.

In order to remove the washing machine tub , you will need two pairs of hands. After removing the counterweights, disconnect the shock absorbers, and then, together with an assistant, carefully remove the tank from the springs and remove it from the unit. Then disconnect the motor from the tank, to do this, first remove the drive belt, then unscrew the motor fasteners. Finally, remove the pulley by removing the bolt in the middle.

Article on the topic: How to turn on the Zanussi aquacycle 600 washing machine

To replace the bearings on the drum, you need to disassemble the tank . The task will become more complicated if it turns out that your washing machine has a non-separable (soldered) tank. In this case, you will need to either completely change the part (which is not cheap) or saw it (the procedure can take several hours, and it is also quite painstaking work).

Replacing the bearing assembly in washing machines with a collapsible tub (for example, in the Samsung Diamond 6 kg model) is much easier. The two halves of the tank are held together by coupling bolts and latches that need to be separated. To dismantle the bearing assembly, you can use a special automotive puller or carefully knock down the metal rings with a hammer and chisel. Then you should thoroughly clean the seat and install new bearings and oil seal.

Not all washing machine breakdowns can be fixed on your own. For global repairs, you will need the help of a professional and a special tool.

After replacing and repairing all elements of the device, reassemble the machine in the reverse order of dismantling. Notes, photographs and notes made with a colored marker will be useful to you.

Now you know how to disassemble a Samsung washing machine. Follow our recommendations, do not forget about the instructions, check the diagrams and record your actions. We hope that our article will be useful to you. Happy renovation!

Washing machine Samsung WF8590NLW8

Samsung WF8590NLW8 is a washing machine with a 6 kg load, a voltage stabilizer and a ceramic heating element to prevent scale deposits. A drum with a special shape of drainage holes prevents excessive foaming, but allows the soap solution to penetrate faster and deeper into the fabric. Excellent washing results and stain removal are achieved.

The WF8590NLW8 washing machine consumes 48 liters of water per wash cycle. Energy consumption is 1 kW/h. These are indicators of maximum energy efficiency. At the same level - washing class (A). During a standard cycle, all types of contaminants are removed from laundry.

Model features:

• Ceramic heater. It features durable operation. Resistant to the deposition of calcium salts on the surface of the element. Allows you to save on special chemical solvents. Saves energy;
• Stable operation during mains voltage fluctuations. The model operates normally in the range of 185-400 V;
• "Diamond" drum. Diamond Drum technology has a 4-sided shape of recesses with small diameter holes. Designed for gentle and effective washing;
• Silver Wash technology. Helps fight bacteria, fungi and allergens. “Silver” washing is so named due to the presence of silver ions in the soap solution. The hygienic cleanliness of products is achieved, as when boiling;
• Informative display. LED-backlit control panel with easy-to-read prompts. It's simple to operate.

Specifications Samsung WF8590NLW8

Pros and cons of Samsung WF8590NLW8

Pros of the Samsung WF8590NLW8 washing machine:

• There is protection against children;
• Clear menu;
• Many functions;
• Attractive design.

• May make noise when spinning;
• There is no mode at low t.

Weee Sign Instructions

Page 5

• Image
• Text

precautionary measures _5

These warning signs are posted here to prevent injury to you and others. Please watch them closely. After reading this section, keep it in a safe place for future reference.

Please read all instructions before using this machine.

This machine, like any equipment that uses electricity or moving parts, is potentially dangerous. To operate this machine safely, be familiar with how it operates and take proper care of it when you use it.

This machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the machine by a person responsible for their safety.

Supervise children to ensure they do not play with the machine.

INSTRUCTIONS REGARDING THE WEEE MARK

How to properly dispose of this machine (Unnecessary electrical and

electronic equipment)

(Applies to European Union countries and other European countries with separate waste collection systems)

This marking on the product, accessories or printed matter indicates that this product and its electronic accessories (e.g. charger, headphones, USB cable) at the end of their useful life should not be mixed with other household waste. To avoid possible harm to the environment or human health due to uncontrolled disposal of unwanted items, please separate these items from other pieces of discarded equipment and reuse them to promote the sustainable reuse of material resources.

Home users should contact either the retailer from whom they purchased this product or their local authority office to find out where and how to return these devices to them for environmentally safe reuse.

Users who are doing business should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be disposed of with other commercial waste that will be disposed of.

WARNING

WF8590NG-02607R_EN.indd 5

2009-11-7 16:44:15

Washing machine Samsung WF8590NLW9

Samsung WF8590NLW9 is a full-size washing machine with a front hatch, the ability to simultaneously load 6 kg of laundry, a wide range of programs and an indication system to make it easier to control modes.

What to look for when purchasing

8 automatic washing programs allow you to properly care for clothes made from any fabric with any degree of soiling. The small number of washing programs is compensated by the ability to manually adjust the temperature. The maximum value of 95° is equivalent to boiling. The spin speed of 1000 rpm in the upper value can be reduced using the regulator. At maximum speed the noise level reaches 74 dB.

Functional features:

• Heating element with ceramic coating. Reliable and durable in operation, protects the machine structure from scale;
• Voltage regulator. Eliminates machine breakdown due to power surges;
• Imbalance protection. Automatic redistribution of washed laundry before spinning when an imbalance is detected. Drum rotation speed control. Reduces vibration and noise;
• Child protection. After the program starts, the washing machine controls are locked to avoid outside interference;
• Self-diagnosis. Automatic analysis, identification of operational problems, notification to the owner by displaying an error code;
• Delayed start. The time interval is set at the user's discretion;
• Display system. Light indicators indicate the time, the presence of locks, selected functions, and the end of the wash.

Specifications Samsung WF8590NLW9

Pros and cons of Samsung WF8590NLW9

Pros of the model:

• Simple controls;
• Capacious drum;
• Low cost.

• Few programs;
• No additional rinse.

Precautionary measures

Page 6

• Image
• Text

6_

precautionary measures

IMPORTANT WARNING INFORMATION

CONCERNING INSTALLATION

Installation of this product must be performed by a qualified technician or service company. — Failure to do so may result in electric shock.

fire, explosion, product performance problems, or personal injury.

This machine is heavy, think about how to lift it.

Plug the power cord into a 220V 60Hz 15A AC wall outlet and use this outlet only to connect this machine. Also, do not use an extension cord. — Using a wall socket to simultaneously connect other devices

using a tee or extending the power cord may result in electric shock or fire.

— Make sure that the supply voltage, frequency and current are within the specified values.

which are indicated in the technical specifications of the product. Failure to do so may result in electric shock or fire. The power plug must fit securely into the wall outlet.

Regularly remove all foreign matter, such as dust or water, from the power plug pins and contact surfaces with a dry cloth. — Pull out the power plug and clean it with a dry cloth. — Failure to do so may result in electric shock or

fire.

Insert the power plug into the wall outlet in the correct position so that the cord points toward the floor. — If you insert the power plug into the outlet in such a way that the power cord

goes in the opposite direction, the electrical conductors in the cord may be damaged, resulting in an electric shock or fire.

Keep all packaging materials out of the reach of children, as the packaging materials may be hazardous to children. — If a child puts his head into the bag, this could lead to suffocation.

If this machine or the power plug or power cord becomes damaged, contact your nearest service center.

This machine must be properly grounded. Do not ground this machine through a gas pipe, plastic water pipe, or telephone line. — This may result in electric shock, fire, explosion, or malfunction.

product operation.

— Never plug the power cord into an outlet that is not properly grounded.

way. Make sure grounding complies with local and national codes.

Do not place this machine near heaters or flammable materials. Do not place this machine in a damp, oily or dusty place, or in a place exposed to direct sunlight or water (such as raindrops).

Do not place this machine in places with low temperature.

Precautionary measures

WARNING

WF8590NG-02607R_EN.indd 6

2009-11-7 16:44:16

Washing machine Samsung WW65K42E08W

Specifications Samsung WW65K42E08W

Pros and cons of Samsung WW65K42E08W

Pros of the model:

• Quiet;
• Possibility to add items during washing.

Washing machine Samsung WW65K42E00S

Specifications Samsung WW65K42E00S

Pros and cons of Samsung WW65K42E00S

Pros of the model:

• Separate spin and rinse;
• Convenient hatch for adding laundry;
• EddWash function.

• Poor water supply.

precautionary measures…

Page 7

• Image
• Text

precautionary measures _7

— Frost can cause pipes to burst.

Do not install this machine in places where gas may leak. — This may result in electric shock or fire.

Do not use an electrical transformer. — This may result in electric shock or fire.

Do not use a damaged power plug, damaged power cord, or loose wall outlet. — This may result in electric shock or fire.

Do not pull or bend the power cord excessively. Do not twist or tie the power cord. Do not hang the power cord on metal objects, place something heavy on the power cord, place the power cord between objects, or place the power cord in a recess on the rear of the machine. — Failure to do so may result in electric shock or

fire.

Do not pull on the power cord when removing the plug from the outlet. — When removing the plug from the socket, hold onto the plug. — Failure to do so may result in electric shock or

fire.

Do not place the power cord or hoses where you could trip or fall.

WARNING INFORMATION CONCERNING

INSTALLATIONS

This machine must be installed so that the power outlet is accessible. — Failure to do so may result in electric shock or

fire due to current leakage.

Place your machine on a level, firm floor that can support its weight. — Failure to do so may cause abnormal vibrations, movement

machines on the floor, noise or problems.

IMPORTANT WARNING INFORMATION

CONCERNING THE USE OF THE MACHINE

If the machine floods with water, immediately turn off the water and power supply and contact your nearest service center. — Do not touch the power plug with wet hands — Failure to do so may result in electric shock

If the machine emits a strange noise, a burning smell, or smoke, immediately unplug the power plug and contact your nearest service center. — Failure to do so may result in electric shock or

fire.

If there is a gas leak (such as propane, LPG, etc.), ventilate the area immediately without touching the power plug. Do not touch the machine or the power cord. — Do not turn on the fan.

ATTENTION

WARNING

WF8590NG-02607R_EN.indd 7

2009-11-7 16:44:16

Washing machine Samsung WW65J42E0HS

Specifications Samsung WW65J42E0HS

Washing machine Samsung WW65K52E69S

Specifications Samsung WW65K52E69S

Pros and cons of Samsung WW65K52E69S

Pros of the model:

• Sensitive sensor;
• Quiet;
• Excellent washing quality;
• Additional door for linen.

Washing machine Samsung WD70J5410AW

Specifications Samsung WD70J5410AW

Pros and cons of Samsung WD70J5410AW

Pros of the model:

• 14 washing programs;
• Big drum;
• Good drying.

Prices for Samsung models

Note. Instructions for washing machines can be viewed online, downloaded and printed.

General information

Washing machines from this company have firmly taken their place in the household appliances market. This is due to a combination of attractive appearance, practicality and a large selection of washing machines with various functions. Separately, we need to highlight the Samsung Diamond model line.

In these models, you can always choose a washing machine that meets all the requirements for the volume of loaded laundry, dimensions, color, and set of functions. All equipment has a low energy consumption class, this is an important indicator for saving energy.

Attention: An absolute advantage is the large number of Samsung service centers around the world. This makes it possible to quickly solve a problem related to the operation of this company’s equipment.

Description: washing machine Samsung WF8590NMW8

Washing machine SAMSUNG WF8590NMW8

good model, nothing superfluous. This model has a relatively small number of pre-installed programs, none that are useless. The washing machine's controls are simple, even a child can figure it out; the settings for manual modes are very flexible, and are suitable even for the most demanding and perfectionists.

Samsung WF8590NMW8

quite roomy. You can wash up to 6 kilograms of laundry in one wash. Spin speed - up to 1000 rpm. It works quietly and consumes little energy. Some buyers had difficulties installing this model, namely adjusting the legs.

Samsung WF8590NMW8

has a large number of advantages, with only a few minor disadvantages.

Washing machine SAMSUNG WF 8590 NMW8. Advantages and disadvantages

Advantages

:

• golden mean: price/quality;
• high build quality;
• service and warranty for the washing machine;
• high-quality laundry;
• simple installation that does not require special skills;
• beautiful design and appearance;
• simple and intuitive controls;
• very spacious 6 kilogram drum;
• very quiet during washing;
• a large number of useful washing modes;
• stable, does not “jump” during spinning;
• there is a countdown timer on board;
• squeezes well, at speeds from 400 to 1000 rpm;
• relatively light weight of the washing machine, only 59 kilograms;
• automatic drum balancing (function);
• ceramic heating element and water heater;
• protection from children.

Flaws

:

• short hose for draining water;
• no delicate wash mode;
• no significant deficiencies were found.

Instructions for several models

Please note that the instructions are also suitable for the following models:

• WF8694AH**
• WF8692AH**
• WF8690AH**
• WF8698AH**
• WF8592AH**
• WF8590AH**
• WF8598AH**
• WF8694AM**
• WF8692AM**
• WF8690AM**
• WF8698AM**
• WF8592AM**
• WF8590AM**
• WF8598AM**
• WF8694NH**
• WF8692NH**
• WF8690NH**
• WF8698NH**
• WF8592NH**
• WF8590NH**
• WF8598NH**
• WF8694NM**
• WF8692NM**
• WF8690NM**
• WF8698NM**
• WF8592NM**
• WF8590NM**
• WF8598NM**

Precautionary measures

Page 8

• Image
• Text

8_

precautionary measures

— A spark may cause an explosion or fire.

Do not allow children to play in or on the washing machine. Also, when getting rid of the machine, remove the washing machine door handle. — Once inside the car, a child may become trapped and suffocate.

Make sure that the packaging (sponge, foam) attached to the base of the washing machine is removed before you start using the machine.

Do not wash contaminated parts of the machine with gasoline, kerosene, benzene, paint thinners, alcohol or other flammable or explosive substances. — This may result in electric shock, fire or explosion.

Do not open the washing machine door by force when it is running (high temperature wash/dry/spin modes). — Water leaking from the washing machine may cause burns or damage the floor

slippery.

This may cause injury. — Opening the door by force may cause machine damage or injury.

Do not put your hands under the car. - This may cause injury.

Do not touch the power plug with wet hands. — This may result in electric shock.

While the machine is running, do not pull out the power plug to turn off the machine. — Re-inserting the power plug into a wall outlet may cause a spark and cause

to electric shock or fire.

Do not allow children or infirm persons to use this machine without supervision. Do not allow children to climb on the machine. — Failure to do so may result in electric shock, burns, or

injury.

Do not put your hand or any metal object under the washing machine while it is operating. - This may cause injury.

Do not unplug the machine by pulling on the power cord, always grasp the plug firmly and pull it out from the power outlet directly. - Damage to the cord may result in short circuit, fire and/or shock.

electric shock

Do not attempt to repair, disassemble or modify the machine yourself. — Do not use any fuses (e.g. copper insert,

steel wire, etc.) other than the standard fuse.

— If repairs or reinstallation of the machine are required, contact

the service center closest to you.

— Failure to do so may result in electric shock, fire,

machine breakdown or injury.

If any foreign substance such as water gets into the machine, unplug the power plug and contact your nearest service center. — Failure to do so may result in electric shock or

fire.

Precautionary measures

WF8590NG-02607R_EN.indd 8

2009-11-7 16:44:16