What to do if the vape does not unscrew

How to unscrew?

If the atomizer tank does not unscrew, you can solve the problem in the following ways:

Stop the base. There's no point in putting in too much effort. This is fraught with cracks in the glass, which will become unsuitable for further use. The base can be secured with any thin object that fits into the duct opening. This will help secure the body.
Latex gloves. The easiest way to unscrew an atomizer, glass or drip tip is to use rubber-based gloves or a similar thin mat. This will prevent your fingers from scrolling along the body of the product.
Electrical tape and plaster. If you cannot manually disconnect the clearomizer, use pliers. In order not to deform the glass, the vape is wrapped with insulating tape in 1-2 layers; this should be done extremely carefully. The pliers squeeze the tank only lightly, otherwise the glass will be scratched, and in the worst case, it will burst.

When the tank unwinds, it is better to postpone refueling. All this is a consequence of active vaping - the electronic cigarette needs service. Using a wet cloth or a thin stream from the tap, the joint surfaces are washed and the threads are cleaned. When there are no oily slurry residues on the fastenings, everything is done correctly. Unscrew the rest and rinse thoroughly. Thanks to this, you can fix the glass with only a few turns: clean parts prevent liquid leakage.

Instructions for unscrewing the tank

If the tank does not unscrew, then the problem is solved by performing the following manipulations:

Stop the base without applying any force, as the glass may crack and will not be suitable for further use. Make this with some thin object that will fit into the air vent. This way you will fix the body;
Using rubber gloves or a thin rubber mat, unscrew the evaporator, glass or drip tip so that your fingers do not roll over the body of the device;
Wrap the glass in a couple of layers with electrical tape or adhesive tape so that the glass is not deformed with pliers if you are unable to remove the clearomizer by hand;
Use a wet cloth/thin stream from the tap to rinse the joints and clean the threads. If there are no liquid residues on the fasteners, then everything was done correctly. It is better not to refuel the e-cigar while unwinding the tank;
Unscrew the remaining parts and wash them thoroughly;
Install the glass several times, clean parts will not leak.

How to use a vape correctly?

Problems with detaching and fixing parts in most cases arise due to violation of the rules of use. Professionals recommend:

Act carefully and consistently. First, the drip tip is unscrewed, then the tank cap, and only then the glass and atomizer are removed. If everything unfolded chaotically, you shouldn’t be surprised at the problems.
Protect the electronic cigarette from high temperatures. This may lead to deformation of the glass and case.
Securely fix the evaporator. It is difficult to screw or unscrew the tank due to the crooked position of the atomizer.

This is not uncommon on handmade mech mods and box mods, where you can break the thread or screw in the atomizer at an angle.

Carefully refill your vape. It is undesirable for liquid to get on the joint surfaces. The oil will penetrate anywhere, including causing the vape to leak.

Other unscrewing methods

You can unscrew the atomizer from the base or the tank from the evaporator using special substances. During active vaping, a corrosive coating from burning and liquid remains on the inner surface of the electronic device. This leads to boiling of the elements, which are tightly fixed to the thread and are not susceptible to external influences.

VD-40 will help with servicing your vape; the composition is easy to find in any hardware store. Through the holes in the air duct or through the hole for vaping, you should try to drip WD-40 onto the connection and threads of the parts. Then wait 5-10 minutes. During this time, the plaque will dissolve, and the mobility of spare parts will improve.

After cleaning, it is important to rinse the atomizer to remove any residual WD-40.

When and why?

When and why?
The need to clean this device is due to the formation of burning on the internal elements. You should not allow burning to enter your body; it will end badly for your health. Pure e-cigarette is safe to use.

In addition, fumes affect the operation of the device. The vape begins to work poorly, and therefore the harm from its use increases.

Burnt residues on parts lead to premature failure of individual parts. The device works for less time, and liquid may also leak into the battery.

How do you know when you need to wash your device? When contaminated, the vape changes the taste and smell of the vapor, making steam generation difficult.

You should also rinse when changing the fluid. This information is useful to know if you like to experiment with e-liquids for refilling your vape.

Why should you be careful with glass?

Glass is the most vulnerable element of a vape device. Owners of rare electronic devices ordered from AliExpress or other foreign resources can verify this. It is difficult to find components for new devices in stationary vape shops.

Cracked glass cannot be repaired. Moreover, with frequent unscrewing and tightening, the crack will spread.

To avoid spending money on buying a new vape, it is wise to clean your electronic cigarette after every second or third refill.

In order for you to enjoy the vapor from your electronic cigarette, you need to refill it on time and correctly. Otherwise, the steam generator will simply have nothing to produce steam from.

How to refill the tank of an electronic cigarette correctly, and what safety rules exist?

Other options for unscrewing the tank

Thanks to special substances, it is possible to disconnect the atomizer from the base or the tank from the evaporator. In the process of active vaping, so-called gars are formed inside. Because of them, the components of the liquid boil, which settle tightly on the thread and do not solidify.

WD-40 is a substance that is sold at hardware stores. This composition must be dripped onto the thread through the air duct or hole for vaping the puff. Then you need to wait 5-10 minutes for the plaque to dissolve. Then rinse the vape to remove any remaining WD-40. The mobility of parts is guaranteed to increase.

Glass is the most vulnerable element of e-cigarettes. Owners of rare devices purchased from AliExpress or other foreign online stores have long been convinced of this. Components for new devices are rare in stationary vape shops.

It is impossible to repair cracked glass. In addition, with constant unscrewing/twisting, the crack only increases in volume. To avoid the cost of purchasing a new electronic device, it is more rational to clean your device after every 2-3 refills.

Tanks and clearomizers

In order for you to enjoy the vapor from your electronic cigarette, you need to refill it on time and correctly. Otherwise, the steam generator will simply have nothing to produce steam from.

How to refill the tank of an electronic cigarette correctly, and what safety rules exist?

The refueling process is quite simple, but if certain rules are not followed, various difficulties may arise. For example, what to do if the tank does not unscrew or the following:

how to refill an electronic cigarette correctly;
what types of tanks are there;
how to properly unscrew the clearomizer;
an important rule for pouring liquid;
what to do if the tank does not unscrew.

So, you are a beginner vaper.

You recently purchased your first vape and don’t know how to refill your e-cigarette correctly. The seller was unable to demonstrate this in the store, and the vaping process can't wait to start. Let's try to answer this question.

Steam generator components

Basically, electronic cigarettes are similar in their designs, but there are still some differences.

Let's remember what a steam generator consists of:

Battery.
It supplies the device with energy, with which the device is able to generate liquid into vapor. The battery is charged from the mains or via a USB cable.
Tank.
Or, as it is also called, a cartridge is a device that contains liquid for vaping. It is thick and oily. May contain nicotine or be without it.
Frame.
It can be made of metal or plastic. The cases also differ in size and color.
Microprocessor.
The basis of the electronic component of the steam generator. It is recommended to protect it from liquid in a certain position, as this can damage the microcircuits.
Steam generator.
A device in which oil gets heated and evaporates, turning into steam.
Ultrasonic evaporator.
Plays the role of a filter in an electronic cigarette, additionally protecting the lungs from pollution.

Having found out the components of the electronic cigarette, let's try to find out how to fill the oil.

Methods for refilling liquid

There are only three methods:

the first method is classic.
It is necessary to remove the cartridge from the electrical appliance, then you need to remove the absorbent element from the cartridge by prying it with tweezers. Oil should not be poured to the top, but approximately three-quarters of the volume, holding the tank vertically. This must be done so that when closing, excess liquid does not leak out and get on your hands or in your mouth.
second method.
Using a syringe with a needle of the largest diameter. The vaping liquid is thick, so a thin needle simply won’t push it through. After drawing oil into the syringe, slowly distribute it throughout the cartridge.
third method.
It works if the liquid is poured into a bottle without a dispenser or you practice self-mixing. Use a pipette in this case and repeat the first method step by step.

Depending on the filling method, tanks are divided into two types.

Types of tanks

Structurally, tanks are divided into two subtypes.

With a spiral at the top.
If the spiral is located at the top, then you need to unscrew the top part of the tank, then carefully pour the liquid along the walls of the vessel, avoiding getting into the hole in the air duct. The liquid must not be filled to the top, otherwise it will leak out when the top is tightly closed after filling.
With an evaporator at the bottom of the clearomizer.
With this arrangement, you need to unscrew the clearomizer from the battery counterclockwise. Then turn it over and detach the bottom part. Then, carefully, as in the first method, pour in the liquid without touching the air duct. Then, screw in the lower base and battery in sequence.

It must be remembered that if you perform top filling, then immediately after opening the lid, the liquid must be filled as quickly as possible. You also need to ensure that the lid is always closed and liquid does not flow out through the air duct openings.

Important! The vaping process cannot be carried out if the evaporator is dry. It should always be tucked in and the fibers in it should be saturated with oils. If you are installing a new vaporizer, after filling it with liquid, wait a few minutes so that it is evenly distributed throughout the filler.

Frequently asked questions

The refueling process is quite simple, but if certain rules are not followed, various difficulties may arise. For example, what to do if the tank does not unscrew or the following:

how to refill an electronic cigarette correctly;

what types of tanks are there;

how to properly unscrew the clearomizer;

an important rule for pouring liquid;

what to do if the tank does not unscrew.

So, you are a beginner vaper.

Short story

Since that time, such gadgets have changed beyond recognition and have become hundreds of times more powerful.
If previously they existed only to help a person quit smoking more comfortably, now almost every fifth person has such a device. Some, especially young people, have become addicted to vaping liquids of different flavors, so the popularity of electronic cigarettes is increasing exponentially. Many people are interested in how to care for an electronic cigarette. This is a simple procedure that does not take much time. The first ES were disposable . They were relatively inexpensive, and their manufacturers claimed that this kind of device could replace up to 2 packs of cigarettes for a smoker. In fact, due to their low power, they lasted for a very short time, and the amount of steam and taste left much to be desired. Of course, there was no question of any cleaning: after use, the devices were immediately thrown into the trash. The batteries of such devices could not be recharged, and the taste of the liquid could not be changed. They began to be replaced by the first reusable ES.

Such devices were called e-cigarettes. They cost much more than their disposable counterparts, but they were practically the same in terms of the amount of vapor and taste. For such gadgets, cartomizers were used - removable caps filled with liquid with a certain taste and aroma. The cartridges could be refilled, but the process was labor-intensive and fluid often leaked. The battery of such devices could be recharged repeatedly, but it was impossible to hover while charging.

The evaporator was a twisted wire that was inserted into the cartridge and heated it. The charge held very little, and the composite cigarettes themselves quickly failed, so they had few admirers. Soon, eGo and Armango format devices (models ce4 and ce5) entered the market, which had an improved liquid reservoir and an evaporator. Soon they too became outdated, because they were replaced by various box mods, as well as mechanical mods, which are constantly being improved.

Steam generator components

Basically, electronic cigarettes are similar in their designs, but there are still some differences.

Let's remember what a steam generator consists of:

Battery. It supplies the device with energy, with which the device is able to generate liquid into vapor. The battery is charged from the mains or via a USB cable.
Tank. Or, as it is also called, a cartridge is a device that contains liquid for vaping. It is thick and oily. May contain nicotine or be without it.
Frame. It can be made of metal or plastic. The cases also differ in size and color.
Microprocessor. The basis of the electronic component of the steam generator. It is recommended to protect it from liquid in a certain position, as this can damage the microcircuits.
Steam generator. A device in which oil gets heated and evaporates, turning into steam.
Ultrasonic evaporator. Plays the role of a filter in an electronic cigarette, additionally protecting the lungs from pollution.

How to replace the evaporator in the tank?

How to change the evaporator?

Before installing a new evaporator, it is recommended to disassemble the tank and rinse it with ordinary warm water, removing traces of dirt.
Then you need to screw in a new evaporator, having first dripped it with the liquid with which you will fill the tank.
Fill the tank with liquid and let it sit for a few minutes.

12 Dec.
2022 Interesting materials:

What are maternity payments and what do they consist of? What is the business reputation of an organization? What are cash equivalents? What is Device ID? What is a 32" diagonal? What is a differentiated payment type? What is Application Manager? What is a display port on a video card? What is a display port? What is DLC on Steam?

Types of tanks

Structurally, tanks are divided into two subtypes.

With a spiral at the top. If the spiral is located at the top, then you need to unscrew the top part of the tank, then carefully pour the liquid along the walls of the vessel, avoiding getting into the hole in the air duct. The liquid must not be filled to the top, otherwise it will leak out when the top is tightly closed after filling.
With an evaporator at the bottom of the clearomizer. With this arrangement, you need to unscrew the clearomizer from the battery counterclockwise. Then turn it over and detach the bottom part. Then, carefully, as in the first method, pour in the liquid without touching the air duct. Then, screw in the lower base and battery in sequence.

Berserker RTA – a tasty cigarette puff tank

10.09.2017

Today we are reviewing a new Berserker MTL cigarette tank, in the creation of which Vandy Vape and the popular video blogger Alex From VapersMD took part, who has already released Skill RDA.

The device is intended primarily for those who want to quit smoking, switch from regular cigarettes to electronic nicotine delivery, for whom autonomy is important (for example, vaping in a busy place) and minimal battery consumption.

Equipment

In the box we are greeted by the tank itself, a replaceable spare glass, a spare glass for a volume of 4.6 ml, a black delirine drip tip, a dome with which you can increase the volume of the tank, a set of spare o-rings, a gold-plated pin, screws for stands, a special key for unscrewing the locknut, 2 pre-wound spirals and a Chinese screwdriver.

Information for your information

Vandy Vape Berserker MTL RTA is a tank for a cigarette puff, made of 304 stainless steel in two colors: steel and black, has a 510 drip tip, allows you to increase the tank volume from 2 ml to 4.6 ml by installing a shaft and glass, works on one spiral, also has top filling, bottom airflow and tightening adjustment.

Dimensions: Height: 30/40 mm Diameter: 24 mm

Glass height: 13.47/22.8 mm

Review

On top is a drip tip, which is made of heat-resistant Ultem material. The set includes a delirin one, which can be used with clear glasses. The inside of the drip tip has a conical finish. This was done to prevent condensation from collecting.

The top cover has drop-shaped recesses for easy manipulation when unscrewing. You can twist the cap counterclockwise and gain access to two filling holes, which are quite wide.

This tank has a filling system without blocking the liquid supply holes.

Between the holes you can see a lock nut, which can be unscrewed with the key included in the kit. The locknut holds the dome and prevents the dome from unwinding when unwinding the tank at the moment when you need to remove the base for rewinding without draining the liquid.

The locknut is unscrewed clockwise. The dome is like in the short version, i.e. 2 ml, and long – 4.7 ml, inside has a spherical treatment, this is a taster.

To increase the volume of the tank, you should screw on an elongated dome and install an enlarged glass and screw this structure onto the base.

The base has classic racks like a Sub Tank. One spiral is installed in the racks, which is clamped with two screws. The screws are universal, the head is made with a cross and a slot. The racks have special slots for installing spiral legs. Between the posts there is a hole for blowing the spiral, which has a diameter of 1.4 mm.

At the base of the berserker there are two channels for placing cotton wool and a hole for supplying liquid. The tank has the ability to completely shut off the liquid supply.

On the side of the base there is only one hole for tightening. The tightening is adjusted with an adjustment ring. By rotating the ring you can adjust 5 tightening options: 0.8 mm, 1 mm, 1.2 mm, 1.4 mm, 1.6 mm.

The airflow adjustment has a teardrop shape and at the largest airflow diameter of -1.6 mm, you can use this “droplet” to cut off the airflow as needed, making it tighter. At the very bottom there is a gold-plated pin that is adjustable. Pin performs well.

Installation of the spiral

In Berserker MTL RTA by Vandy Vape, it is recommended to use a Fused Clapton coil 0.25 nichrome and on top of 0.1 nichrome, diameter 2.5 mm, preferably with a resistance of at least 0.65 Ohm for a more pleasant vaping on an analog puff. Installing a spiral is both simple and complex.

The process of fixing the legs of the spiral does not cause any difficulties. At the same time, it is important to correctly center the spiral so that it is in the center of the airflow, as close to it as possible. The excess length of the spiral legs should be cut off flush so that the tips of the legs do not touch the dome, because

Possibly a short circuit in the dome.

Laying wool

The cotton wool should be placed depending on what liquid you are going to soar with. If VG/PG: 70/30, then the wool is laid in the usual way. The cotton wool should not be pushed tightly into the ducts, not tightly. If VG/PG: 70/30, then we “knock” the katon into the ducts harder so that the liquid does not seep into the tank.

Cons and pros

Cons: - rather a small quibble - the small glass is made of Ultem, I wish the small glass was also made of Pyrex.

Pros:

- versatility of airflow, five possibilities to change the diameter of the puff, - 2 options for the volume of liquid in the tank, while with different volumes, the taste is revealed differently, - quality of manufacturing of parts,

-rich equipment: dry-type, o-rings, screws, 2 coils.

Official website of the manufacturer: https://www.vandyvape.com/detail/Atomizer/39 Price: recommended retail price for the steel version is $44.99, for the black version $46.99. Video

Replacing the evaporator

If the steam generator begins to produce a low amount of steam or its taste does not bring you pleasure, then one of the reasons for this may be replacing the evaporator. It, like any structural part, has its own service life.

The force of blowing on the evaporator can be achieved using a silicone ring with slots, by rotating which you can make the holes on the air duct larger or smaller, changing the depth of tightening.

To replace it, you need to unscrew the battery from the clearomizer, then disconnect the tank.

Frequent causes of breakdowns

One of the most common causes of failure is considered to be improper care of the cigarette due to improper use, as well as the use of low-quality flavored liquids or counterfeits of well-known brands . The first piece of advice for novice vapers: buy only licensed liquids that consist of high-quality nicotine (for example, American hiliQ), vegetable glycerin and propylene glycol. Some unfortunate manufacturers are trying to save on raw materials by making vaping mixtures from unrefined pharmaceutical glycerin for external use. Atmose, Nrgon, etc. are considered good liquids for vaping.

Attention! Liquids that contain a high percentage of nicotine, glycerin and flavorings pollute the ES more, so you will have to clean the gadget much more often.

Of course, the optimal time after which to clean your vape is very individual. It all depends on the following factors:

brand and type of ES;
the type of vaping liquid used, its quality;
vaping frequency, etc.

Attention! Before switching from vaping one liquid to another, you should clean the clearomizer of foreign impurities. This way you can achieve a perfectly pure and pleasant taste , and also significantly extend the life of your gadget.

If the tank on an electronic cigarette does not unscrew

Experienced vapers recommend several solutions in such cases:

if the base scrolls, “stop” it with any object that fits into the hole in the air duct and unscrew the tank;
A rubberized mat and rubber gloves will help you remove the drip type, which will prevent the part from turning in your hands;
wrap the glass vessel with electrical tape or plaster to avoid scratches and use pliers.

This must be done carefully so as not to damage the metal parts or crush the glass.

Terms of use

Follow all rules for operating, refueling, assembling and disassembling your steam generator

avoid contact of the cigarette with water;
use only for its intended purpose;
protect from temperature changes and open fire;
disassembling the box mod will void the manufacturer's warranty.

Monitor the amount of fluid and timely and competent replacement. Have a nice couple!

Istick 20. The thread is broken. Option to solve the problem.

Is the tank not spinning up on the Eleaf Ijust S? Break him to *** with the help of my advice