Electrolux top-loading washing machine does not start reasons


Vertical washing machines from the Swedish manufacturer Electrolux are popular due to their quality and pricing policy. But even with them, breakdowns may occur after some time.

To eliminate this problem, you need to familiarize yourself with common malfunctions of Electrolux top-loading washing machines, methods for solving them, and disassembly instructions.

Tips that will help you find a good master will also be useful.

Typical malfunctions of SMA Electrolux

To determine a malfunction, it is not always necessary to disassemble the Electrolux washing machine; it is enough to pay attention to the behavior of the CM during operation.

Let's look at the reasons for breakdowns that are inherent in Electrolux Intuition, Electrolux Inspire and other models.

SMA does not turn on

Have you decided to start the wash, but the machine won’t turn on? Don't panic. Let's understand the reasons:

Problems with water supply and drainage in an Electrolux car

It happens that the Electrolux washing machine does not fill or drain water. For what reasons does this happen:

No powder collection

After pouring the powder into the dispenser tray, the machine releases a stream of water through a special valve. Along with the water, the detergent also goes away. Over time, the CM may stop picking up powder.

What caused the Electrolux washing machine to malfunction?

The most common cause of the problem is a clogged dispenser. To eliminate it, just remove the tray and rinse it under the tap.

If everything is fine with the tray, the inlet valve may be worn. Then it needs replacing.

Washing in the Electrolux machine does not start, the drum does not spin

If you have a problem like this, you can try to fix the problem yourself.

To do this, you need to open the hatch of the Electrolux washing machine and take out half of the laundry. Having thus reduced the load, try to start the SM again. If there is no result, then:

No water heating in Electrolux machine

How can you tell if your SMA is not heating the water? After starting the wash, wait 15-20 minutes. Then place your palm on the sunroof glass. Warm surface - there is heating. And if washing is done in cold water, the reason for this is a malfunction of the heating element.

The thermostat or voltage stabilizer could also be faulty.

Rinse mode does not turn on

A top-loading Electrolusk washing machine did the wash as usual, but does not go into rinse mode? Most likely, the heating element (heating element) has broken. Since the water does not reach the required temperature, the rinse does not start.

The cause of such a breakdown could be the control module. If a system failure occurs, it is enough to reboot the SM within 15-20 minutes. If this happens constantly, you will have to replace the module.

Turning on SM Electrolux leads to knocking out plugs

When you turned on the washing machine, did the automatic transmission break out? This means that there are problems in the electrical network. Never turn on your Electrolux machine again. It's better to call an electrician to find out what the problem is.

What can cause a short circuit:

Spin doesn't work

For what reason does the Electrolux washing machine not spin out clothes?

Electrolux hatch door does not close

Subsequently, the Electrolux washing machine does not start.

Unscrewing the pulley bolt

washing machine pulley bolt The drum needs to be dismantled not only if a foreign object gets in, but also to replace the bearings. Different car models may have different tanks, but the algorithm for disassembling is approximately the same. First you will need to remove the pulley.

The pulley is attached to the drum shaft with a special bolt or nut right in the middle. The pulley twists in a counterclockwise motion, and it is better to place some object, for example, a block of wood, to avoid twisting.

Unscrewing the washing machine pulley bolt

Unscrewing a bolt is a rather difficult task, because it is reinforced with a compound specially poured into the hole that prevents it from unwinding during vibration. What to do if you can’t unscrew the bolt the first time? You can use a gas burner to heat it up. The metal will heat up, move, and require less effort to remove. Before using a gas burner, be sure to read the safety instructions, because working with it requires certain skills.

Electrolux fault codes

The self-diagnosis system allows the user to determine the cause of the malfunction. When the fault code is displayed on the display, you just have to find out its meaning. Then troubleshooting will be quick.

Let's look at the main Electrolux error codes:

Error codeCode meaning
E11No water supply.
E13There is a water leak.
E21Error draining water.
E23/E24There is a problem with the board's triac, which is responsible for the operation of the pump.
E31/E32Pressostat failure.
E33The heating element does not work.
E35Overflow of water. Exceeding the normal level.
E36The heater protection sensor has failed.
E38There is a problem with the pressure switch.
E39The overflow sensor is faulty.
E41/E45Broken mechanical lock, UBL, door handle.
E51/E54Problems with the control module.
E55The SM motor or its wiring is faulty.
E56Tachogenerator failure.
E57The voltage in the circuit exceeds the permissible limits.
E58/E59Error in the operation of the electric motor.
E5A/E5EControl module error.
E61/E62The water gets too hot.
E66Problems in the operation of the heating element.
E71Problems with the thermostat.
E72/E73Damage to the drying temperature sensor. KZ.
E74The thermistor is not positioned correctly.
E82/E84Main module malfunction.
E85Pump problem.
E91There is no communication with the control module. Wiring fault.
E92/E99Error in the control board.
EA1/EA6The DSP has failed. Worn drive belt.
EB1/EB3Problems with wiring. Incorrect voltage.
EF1The water did not drain after the timeout expired.
EF2Too much foam.
EF3Problems with the pump.
EF4The flow sensor does not give a signal.
EF5Drum overload. Stopping the operation of the SM.
EN1Power failure. Problems with the electronic board.
EN3Insufficient voltage in the network.
ENEThe circuit protection relay has broken.
ENFCircuit relay not recognized.

What to do?

The procedure for restoring a washing machine depends on the location and nature of the malfunction.

Drive belt stretch

If a part breaks or is stretched, it is replaced with a similar one. You can perform this procedure yourself. If the new belt breaks, then it is necessary to inspect the springs and bearings.

Entry of a foreign object

If a foreign body is stuck in the perforation of the drum or in the opening between it and the tank, it is removed using tweezers or pliers. If the object is not visible from the inside, then it can only be reached through the hole for the heating element or after disassembling the tank.

Bearing failure

If wear and jamming occur, new bearings and seals must be installed. To gain access to this part, it is necessary to disassemble the tank, so such repairs are carried out mainly in service centers.

If the tank is non-separable, then when the bearings wear out, it is replaced entirely.

Read how to replace bearings here.

Engine or speed sensor failure

To repair a washing machine motor you may need:

  • clean the contacts that connect the motor to the ECU and tachometer;
  • replace carbon brushes;
  • restore wiring;
  • replace the thermistor or winding;
  • tighten the speed sensor fasteners.

A complete replacement is necessary in the following cases:

  • the tachometer has failed;
  • engine rotor is broken;
  • faulty motor parts are cast in epoxy resin.

Problems with the electronic module

Repair of the electronic unit includes:

  1. Checking the board program and, if necessary, flashing it.
  2. Cleaning and restoration of paths.
  3. Replacement of burnt capacitors and other elements.

If the processor or a large number of tracks are damaged, the ECU must be replaced.

Power outages are a common problem with control board failure, so it is recommended to install a voltage stabilizer or relay in front of the washing machine.

Other

In case of other breakdowns that impede the movement of the drum, it is necessary:

  1. If the UBL socket is clogged, disassemble and clean the lock.
  2. When opening the flaps in the lower position of the drum, hook the flap with wire; in difficult cases, disassemble or completely replace the tank.
  3. If there are problems with the positioning device, replace the DSP, restore the contacts or resolder the ECU chip.
  4. If the locking device is faulty, repair the lock, replace the UBL or sensor.

DIY Electrolux car repair

Having examined the malfunctions of Electrolux washing machines, we will analyze their elimination.

Trouble turning on

In order to solve the problems of knocking out plugs and lack of connection, you need to carry out the repairs yourself. If you decide to check the start button contacts, do the following:

Also check the surge protector. Additionally, remove the back panel by unscrewing the fixing bolts. Inspect the wires and the filter itself for damage. Perhaps some contacts have burned out.

If there are no obvious damages, disconnect the filter contacts and test them with a multimeter.

How to replace a faulty filter, watch the video:

Problems with water intake and drainage

The cause of the problem of filling the tank in the Electrolux washing machine may be a clog in the inlet hose or filter. How to clean the system yourself:

The design of the Electrlux washing machine is such that a drain pipe is provided for normal water drainage. If problems arise with the drain, you need to inspect and clean the pipe. A little DIY repair, or rather cleaning:

Check it for blockages. Clean if necessary.

You also need to check the drain pump, a breakdown of which can lead to problems with draining and spinning. Watch the video for more details:

The drum does not rotate

Repairing an Electrolux washing machine with vertical or front loading is possible with your own hands. To do this, you need to check the engine drive belt.

It could weaken and slide off - then you will have to put it back in place, or it could wear out - then a replacement is necessary. You can do this simple repair yourself:

The cause of this malfunction may be the engine itself. How to check its functionality, watch the video:

Heater failure

If the Electrolux washing machine does not heat the water or does not start rinsing, the heating element is probably broken. How to make a replacement:

How to check the heating element for serviceability is described in detail in the video:

Malfunction of the hatch door in the washing machine

We have already written above why the door may not close.

Immediately check the tightness of the closure by pressing the hatch with your hand. Then inspect the handle and mechanical lock for serviceability.

The UBL, an electronic lock, could also fail. The video shows how to replace the UBL with your own hands:

Noisy operation of the Electrolux machine

During operation, the machine began to make a lot of noise and rumble. This is a sign that the bearings are failing. Not everyone can change them, because you need to completely disassemble the Electrolux washing machine.

Video to help you:

Now you know how you can repair a washing machine yourself. All that remains is to wish you good luck!

Source

Instructions for disassembling a household appliance

The disassembly process begins with preparation, it is important:

  1. Prepare your tools in advance. You will need screwdrivers, pliers, and open-end wrenches. Additionally, you should stock up on WD-40 spray or an equivalent.
  2. Prepare the place. The washing machine is a large piece of equipment, and you need enough free space to disassemble it.
  3. Unplug the machine from the socket.
  4. Drain off any remaining liquid and remove the laundry from the drum.

The next step will be to dismantle the external components of the washing machine. You need to remove the lid, walls, detergent compartment, to do this:


  1. On the back you need to find and unscrew two screws and remove the panel.

  2. The cuvette for household chemicals must be removed all the way and pressed on the “tab”, it is located in the rinse aid compartment.
  3. Unscrew the fasteners that are under the powder box, and additionally unscrew the hatch fixing screws.
  4. The hatch clamp should be slightly pryed with a screwdriver and carefully pulled off.
  5. There are screws to the left of the electronic panel; you need to remove them, and then pry up the fasteners to remove the electronic module.
  6. Once the module is pulled out, you will have access to the screws holding the back and front panels.

The final stage of disassembly will be the removal of the tank-drum assembly. It is better to do this with an assistant, because removing the drum yourself is quite difficult.

Instructions:

  • first you need to disconnect the terminals from the power unit, then turn the pulley with one hand and tighten the belt with the other;
  • you need to unscrew the screws securing the engine;
  • after unscrewing, the motor needs to be moved a little and pulled out;
  • Then the pump wires are disconnected, the screws are unscrewed - to move the pump it must be turned clockwise;
  • removing the wiring and sensor and heating element, then unscrew the nut located in the center, pull out the heating unit using swinging movements;
  • the screws of the counterweights are unscrewed, the components are dismantled;
  • After this, all that remains is to remove the dispenser pipes, the filling valve wiring and the pressure switch.

Basic malfunctions of the Electrolux top-loading washing machine, do-it-yourself repairs

Vertical washing machines from the Swedish manufacturer Electrolux are popular due to their quality and pricing policy.
But even with them, breakdowns may occur after some time. To eliminate this problem, you need to familiarize yourself with common malfunctions of Electrolux top-loading washing machines, methods for solving them, and disassembly instructions.

Tips that will help you find a good master will also be useful.

Bearing wear – from RUB 3,800*

Bearings are responsible for the smooth rotation of the drum.
As the SMA is used, and also due to its overload with linen, the omentum weakens. Moisture gets into the bearing and the corrosion process begins. Over time, the bearing deteriorates. SIGNS

The Electrolux washing machine makes unusually loud sounds when operating: creaks, rattles, crackles. This can be heard especially clearly when the SMA is operating at high speeds. If you shake the drum with your hand, you may notice that it “dangles” more than usual. When disassembling the machine, rusty traces of moisture leaks from the bearings are visible on the tank.

If the bearings are completely destroyed, the drum may completely jam or fall down. The breakdown may be accompanied by code E50.

HOW TO FIX

The bearings need to be replaced with new ones.

*Rates are only for the work of the master; new oil seals and bearings are paid separately.

TOP 10 typical breakdowns of Electrolux ACS and ways to solve them

There are a lot of factors that can affect the performance of a washing machine, but some are very rare, while others are many times more common. To solve basic problems, it is enough to study 10 typical breakdowns and ways to fix them.

Doesn't start

When the clothes are loaded into the drum, the powder is in its compartment, and all that remains is to select a mode and start the equipment, a problem may arise: the washing machine does not turn on. The difficulty is that the information board also does not work, so for diagnosis you will have to conduct a visual inspection:

The surge protector is located under the wall; its malfunction may be indicated by burnt marks or swelling of the housing.

Water does not fill or drain

Washing machines are designed in such a way that the water is changed several times during one wash. You can detect that the malfunction is in the liquid intake immediately after turning it on; there will be no noise accompanying the process, and the washing will not start.

Cleaning the tract will help solve the problem:

Powder is not picked up


After several years of use, the quality of washing noticeably drops.
There are stains on clothes, and it’s not at all due to wear and tear on the equipment. It happens that the problem is that part of the powder remains in a special compartment , and only clean water is used when washing.

How can I restart the machine?

When the Electrolux washing machine freezes without completing the operating cycle, shows no signs of operation and does not respond to button presses, you can return it to operation by resetting the settings and starting the machine again. To complete this task and return the device to functionality, you should hold down the Start key and keep it pressed for ten seconds. This will cancel previously scheduled processes. After this, you should enter the settings again and turn on the operating mode you have chosen.

It is quite possible that you have a machine that was produced 10-15 years ago. Then you should move the program selector to the neutral position. As soon as the program execution stops, the green indicator on the housing will flash and then go out.

If this does not happen, there is a malfunction of the device or an erroneous interruption of its operation. If the program reset is unsuccessful, you should completely reboot the device. The procedure here will be as follows:

  • switch the programmer to the neutral position;
  • press and do not release the Start/Stop button for at least 5 seconds;
  • disconnect the washing machine from the power supply by unplugging the plug from the socket;
  • After waiting about 25 minutes, connect to the power supply again and initiate the program you have chosen.

If the device does not respond to pressing buttons or switching the handle, you must immediately disconnect it from the power supply. A failure in the power supply while the machine is executing a program can damage its control unit. If the measures you have taken to restore the operation of the device do not bring results, you should contact a service center.

Call the master

Sometimes you can’t do everything yourself, or it’s just scary to get into the washing machine without experience in performing such work. In such cases, it is better to call a specialist.

There are several options:

The cost of services depends on the pricing policy of a particular company or master and even on the city of residence. The table shows approximate prices for replacement parts:

Call a specialist, diagnostics500-1000 rub.
DrumFrom 2000 rub.
Motor replacement/repairFrom 1500 rub./from 750 rub.
ButtonFrom 1000 rub.
Water level/temperature sensorsFrom 1200 rub.
BearingsFrom 2500 rub.
Email module From 2500 rub.

Other, less difficult to install components, for example, a power cord, a hatch latch, or removing a third-party object, will cost about 1000-1500 rubles including labor.

Unfortunately, there are quite a lot of scammers, because of them you can lose both money and equipment. Common schemes:

Sudden power outage

In the event of an unplanned power outage, the device should be disconnected from the network as soon as possible. For this purpose, you need to remove the plug from the socket. This way you will protect your washing machine from sudden power surges.

When power is restored, reconnect your device. If the reboot fails, the machine will continue executing the interrupted program. A number of Electrolux models provide a special mode in which, after a power failure, the device gets rid of water and remains in the neutral position. After this, you should set the desired mode again and re-initiate the program.

When faced with a particular short-term problem, you need to find out what caused it. Problems are divided into two categories:

  • mechanical;
  • software.

The first type of fault means that you will need a professional repairman. He will thoroughly determine what caused the malfunction, repair it and advise how to avoid this in the future.

In the second case, the control panel of the washing machine is blocked, and pressing its buttons is useless. To restore the equipment's functionality, unplug it from the power grid for approximately 30 minutes. Then reconnect and enable the operating mode of your choice.

Interesting:

  • How to reset the program on an Indesit washing machine?
  • How to reset an error on a Bosch washing machine
  • Bosch washing machine service test
  • Brush light flashes in Bosch dishwasher
  • Zanussi dishwasher errors
  • Error codes for AEG washing machines

Reader comments

Share your opinion - leave a comment

Fault codes and main breakdowns

Let's look at the main error codes:

There are still many codes in Electrolux washing machines. We have indicated those that occur most often.

Causes and signs of failure

Not all problems are indicated by symbols on the display. Some can be identified by external signs.

Top-loading washing machines often suffer from wear on the drum supports, replacing which can be compared to installing a new bearing. You have to completely disassemble the unit. The following breakdowns also occur:

Repairing a top-loading Electrolux washing machine is best left to a professional. Inside the case, the parts are located very closely, so repairs are carried out almost by touch. If you want to do the work yourself, this video will help you:

Pump problems

Often, pump malfunctions prevent the machine from starting or finishing washing. Depending on what kind of problem appeared with the water, you can determine whether the pump itself or the filter has broken down. Both the filter and the pump itself are quite easy to repair with your own hands. These malfunctions, as they say, are not worth a damn.

Many Electrolux car models have a self-cleaning pump. Washing machines with this element make people's lives easier. Of course, it makes sense to produce such washing machines, with such a pump, and buy them. The filter in them cannot break. The self-cleaning pump is a fairly durable part that should last approximately 3-5 years. The Electrolux EWS-1046, for example, has just such a pump installed.

After seeing the photo, it’s easy to fall in love with this beautiful front-loading washing machine. It is simple and perfect. Perhaps, only if vertical loading is more tempting or a different set of standard functions is needed, will there be a desire to buy something else. Electrolux washing machines EWS-1046 are a popular model. What to do if this pump breaks down? It cannot be repaired. You will have to buy a new self-cleaning one and replace it completely. Electrolux washing machines EWS-1046 are beautiful appliances, practical and convenient. After the self-cleaning pump is replaced, the machine will continue to work and will work for many years.

Repairing Electrolux EWS-1046 is no different from repairing EWS-1020, for example. All spare parts are on sale. But be sure, when buying a part, you should check with the seller: who the manufacturer is, whether it fits this model - read the instructions, if there are any, compare with the old part. It is better to repair these washing machines using spare parts from trusted suppliers - original or analogues. Some parts are suitable for Electrolux EWS-1020, but not for Electrolux EWS-1046. It doesn't hurt to be mindful. It is better to take your registration certificate with you.

Problems with compactor and drum

Strong vibration and movement of the machine during operation is a potentially dangerous situation. This is a massive piece of equipment that will cause a lot of trouble, despite the fact that it seems static. When vibration is strong, washing machines can move and even fall. Water pipes, parquet floors, and furniture are in danger if washing machines do not want to stand quietly in one place. The culprit is either an uneven floor, improper installation, or a drum bearing.

The bearings in Electrolux cars are of high quality and should certainly last at least 6-7 years. If time has passed, or the rubber has worn out due to operating conditions, fluid will leak from the drum and there will be strong vibration. Needs renovation. The drum may also become deformed. You cannot wash it in such a machine.

Self-repair is possible in this case. What does he mean? Nothing complicated. Repair in this case comes down to three simple steps:

  • buy a seal;
  • remove the old one;
  • put a new one in its place.

This part is fixed securely using special latches. Taking a closer look at the car you can understand what's what. Often the information is in the instructions. So almost anyone can do it. The repair will be successful. The only “but” is physical stress. A certain level of physical fitness won't hurt. You can entrust the repair to a specialist, because he, of course, is better versed in this. The work will be done much faster.

If you wish, you can repair any household appliances yourself. All that is required is a love of mathematics, physics, chemistry, and mechanical engineering. A mathematical mind, perhaps. And, of course, a tool will come in handy. Repairs are inconceivable without a screwdriver.

Program selector

If there are errors related to the device for switching and selecting programs, it is almost impossible to correct them yourself. The simplest thing is to buy an electronic module and replace it.

Very often the configuration fails and you have to re-enter data into memory or overwrite it. The average person does not have such equipment (a stand for rewriting volatile memory), so they have to call a specialist.

Errors and reasons:

CodeDescriptionCauses
E82Selector set incorrectly
  1. 1. The processor board is faulty. False data is stored in memory.
  2. 2. Selector error.
  3. 3. Broken electrical wiring
E83The selector data is not being read correctly. Code E83 appears only in testing or diagnostic mode on a bench Electronic module error. It incorrectly detects the device configuration
E93,
E94
The washing unit configuration is incorrectProgram cycles fail.
Such a defect can only be corrected by entering the correct configuration code.

It is necessary to replace the processor board or write new data to non-volatile memory

E95The connection between the non-volatile memory and the main processor is broken. They are located on the main controller Possible open circuit between EEPROM and main processor
E96The configuration of the electronic module does not match the external elements connected to itErrors in the controller software
E97The position of the selection selector does not correspond to the software of the processor usedIncorrectly entered configuration code or replace the main unit.

Diagnostics

Without special equipment, it is simply impossible to check a number of elements of the washing machine. For example, an electrical part or a control unit. If we are talking about mechanical problems with one or another element of the machine, then you still need to disassemble the device, then look for the problem and decide whether it can be fixed with your own hands, whether a specific element can be repaired or whether replacement and other spare parts are needed.

After all, even if we talk about the problems from the list presented above, we can see that the cause of a particular breakdown can be several different cases.

And even a technician cannot always immediately determine the cause of a washing machine malfunction. Therefore, the diagnostic question will be individual in each case and depend on the operating rules of the washing machine.

The washing machine is leaking

Water leakage is a fairly common phenomenon, which is typical not only for Electrolux washing machines, but also for equipment from other manufacturers. There are several reasons why liquid appears on the floor near the washing machine. The first is damage or insufficiently strong fastening of the drain or filling pipe; the second is wear of the hatch cuff. Third - clogged detergent dispenser; the fourth is that the water pressure in the water supply is too high and the fifth is that the drain filter is loosened.

The user can remove the blockage in the tray, tighten the filter tighter and reduce the pressure on his own. In other cases, you will have to disassemble the washing machine, so it is better to use the services of a specialized workshop.

All indicators are on

If the equipment turns on, but the washing process does not start, and the indicator lights are on, this indicates problems with the hatch blocking.

The washing machine locks the door at the beginning of the wash cycle. If the door is not locked, you need to measure the voltage supply to the UBL, having first removed the front part of the equipment body. The check is performed by a tester. If the voltage passes, but the blocking does not work, the UBL needs to be changed. When there is no voltage, most likely the electronic unit or control device is faulty.

0 Helped me

The washing machine is leaking

Water leakage is a fairly common phenomenon, which is typical not only for Electrolux washing machines, but also for equipment from other manufacturers. There are several reasons why liquid appears on the floor near the washing machine. The first is damage or insufficiently strong fastening of the drain or filling pipe; the second is wear of the hatch cuff. Third - clogged detergent dispenser; the fourth is that the water pressure in the water supply is too high and the fifth is that the drain filter is loosened.

The user can remove the blockage in the tray, tighten the filter tighter and reduce the pressure on his own. In other cases, you will have to disassemble the washing machine, so it is better to use the services of a specialized workshop.

Electronic module errors

Very often, the processor unit or wiring is to blame for the inadequate operation of the washing unit. You can determine the cause by the code, but it is not always possible to repair the module on your own.

To search for a burnt or defective part, you need a special stand, which is available in workshops. Its workers will repair the unit or select a new one.

Reasons for module failure:

  • E5A Cooling radiator temperature threshold exceeds 88°
  • E5B The DC voltage on the corresponding bus is much lower than the allocated value of 175 V
  • E5C The constant potential in the relevant circuit is much higher than the required value of 430 V
  • E5D FCV is unable to receive/send operation signal within a 2 second period
  • E5E No communication between the processor module and the FCV control board
  • E5F Frequent control program resets are observed. Because of this, the FCV board continuously polls the machine configuration
  • E84 Recirculation pump signals are not recognized. There is no voltage at its contacts or always has a potential of 5 volts
  • E91 The connection between the machine remote control and the processor unit is broken
  • E92 The main electronics are not coordinated with the user interface
  • E98 Engine control module does not match with processor board
  • EBE Protection relay damaged
  • EBF, EHF Safety circuit is not recognized correctly
  • EB1, EH1 Power supply frequency is not normal
  • EB2, EB3, EH2, Mains voltage too high or low
  • EH3 Interference in the network or the power supply is faulty.
  • If there are errors EB1, EH1 or EB2, EB3, EH2, you must verify the discrepancy between the parameters by measuring them with a multimeter or frequency meter. If the network voltage is often too high or too low, you need to buy and install a stabilizer.
  • EH3 appears , you need to stop the machine and check the network. If there is no interference, there is normal voltage and frequency, change the ED.

Peculiarities

The Electrolux EWT 1266 FIW model has the following overall dimensions - height 85 cm, width 40 cm and depth 60 cm. White body with vertical (top) loading of laundry.

Wash

. The Electrolux EWT 1266 FIW machine has 8 programs, of which we list special ones: washing delicate fabrics, economical program, wrinkle prevention, denim, washing sportswear, super-rinse, quick wash, pre-wash. Water consumption for a full cycle is 53 liters, with a maximum load of laundry - 6 kg.

Plastic tank

, which reduces weight and reduces noise during operation, but increases its fragility, for example during transportation.

Energy consumption

. This model has an energy efficiency class of “A+” (very good), which means that the energy consumption when cleaning 1 kg of cotton clothes at 60 °C will be less than 0.17 kWh/kg.

Leak protection

controlled by sensors and blocks water spills in emergency situations. The Electrolux EWT 1266 FIW model provides complete protection, i.e. If the hose breaks or water gets into the housing, the water supply from the water supply will be immediately blocked.

Drum balance control

during spinning, it helps in cases where a lump of things forms; in such a situation, the mechanism spins the drum in the opposite direction or reduces the speed, until it turns off. This helps extend the life of the Electrolux EWT 1266 FIW and reduces vibration and noise levels during operation.

Foam level control

necessary if the washing powder was chosen incorrectly or there was more detergent than needed. In this case, after rinsing, the pump pumps out excess foam, which gives a better rinse and protects the electronics from moisture.

Delay start timer

helps if you need to start washing when you, for example, are not at home or when you are already sleeping.

Child lock

makes it possible to lock control buttons, this is useful when a child can cancel or change a program, the function is launched by pressing several keys.

Reloading laundry

. Electrolux EWT 1266 FIW is equipped with a function where you can add laundry when water has already begun to fill the drum.

Inverter motor

has no brushes, due to which it wears out less and runs quieter; usually such motors last longer. In addition, they consume

30% less energy.

Sound module errors

Common sound module malfunctions:

CodeDescriptionWhat to do
E99The sound unit, if present in the unit, does not work or makes inadequate sounds (hum, whistle)It is necessary to check the sound board and the wires going to it
E9AThe software implemented in hardware between the input/output electronics and the speaker is faultyCheck main electronic module

If, when washing, a hum, a whistle starts to come from the machine’s speaker, or it simply “goes silent,” you need to examine the sound unit. If there is inadequate noise, one of the wires may break. This can be detected with a multimeter.

In all other cases, the sound unit or processor module must be repaired in workshops.

Rating
( 2 ratings, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]