Operating instructions for the Tefal pro express steam generator

The Tefal steam generator is a household appliance that consists of a tank with a heating element, in which hot steam is created with a pressure above atmospheric, and an iron with holes in the sole.
The device is used for ironing and shaping fabric products through vertical or horizontal steaming.

This article provides instructions for using the Tefal steam generator in Russian.

Preparing for work

The main purpose of Tefal steam generators is ironing and steaming clothes. Hot steam penetrates three to four layers of fabric, which helps reduce ironing time several times.

The procedure for preparing the device for operation:

• fill the reservoir with water;
• connect to a 220V network;
• set the temperature regulator to the maximum position;
• move the power button to position 1.

The water heats up to 160⁰C within a few minutes. The pressure of the steam generated does not exceed 4-7.5 bar. The devices operate in two modes: steam release over the entire plane of the sole and a burst of steam from the spout.

Before starting work, you need to release a certain amount of steam in order for the water pump to work.

Steam pressure may change during operation of the device , since with prolonged steam formation the water temperature decreases by several degrees. Even in this case, you can continue to work safely, since the set pressure will be restored automatically.

Each device comes with illustrated instructions “Safety precautions and rules of use.” When you first start, check your actions with the instructions at each stage of the action.

Before using the appliance, make sure that the material is suitable for steam cleaning . To do this, steam a section of the product from the wrong side. Let dry and check for damage.

Before work

It is not difficult to prepare the device for use. After completing simple manipulations, you can begin ironing and steaming things.

Beginning of work:

• Place the stand with the iron on a stable surface.
• Make sure that the connecting cords do not interfere with the work process.
• Disconnect the boiler and fill with water (not in all devices).
• Insert the container into place until it clicks (for generators with a removable tank).
• Turn on the steam generator.
• Select mode.

Separately, it is worth dwelling on the quality of the liquid being poured.

The use of water whose composition does not meet the hardness requirements will lead to the appearance of scale and premature failure of the device.

According to the instructions for steaming, the use of five types of solutions is allowed:

1. Regular water from the city water supply. One condition is that the content of calcium and magnesium cations should not exceed 6 degrees of hardness.
2. Liquid that has been purified through special filter devices.
3. Bottled water without mineral impurities.
4. A solution of purchased water plus hard tap liquid (1/1 ratio).
5. A mixture of distilled and ordinary water in equal parts.

You cannot upload:

1. Pure distillate.
2. Mixtures with detergent additives.
3. Liquid with high salt content.
4. Carbonated and mineral solutions.

The design of the device, as well as the markings of the control buttons, allow you to work with the steam generator without any problems.

It is necessary to monitor the level of liquid and the compliance of the selected mode with the tissue being treated.

If questions arise during operation, you can always read additional information in the instructions for the Tefal steam generator.

How to use: ironing features depending on the model

Steam generators of the Liberty and Fasteo series produce steam at a pressure of 5 bar. The devices quickly heat water to the required pressure level and steam dresses, suits, coats, curtains in a vertical position, without the use of an ironing board.

Classic models with simple controls from the Effectics, Optimo, Easy Pressing series provide effective care for things at no extra cost .

Steam vents are located on the nose, side and central parts of the sole. The steam supply mode is adjusted manually.

steam generators feature advanced features that make ironing convenient and easy . Moreover, these devices are easy to use and maintain.

The Express Easy Contr model adapts to the material without unnecessary settings, providing automatic adjustment of steam parameters.

A similar No setting technology is used in the Effectic Anti-Calc steam generator, which allows you to iron items in a row without sorting them by fabric type.

steam generators will provide gentle care for various types of fabrics, including expensive and delicate ones . The device has double anti-scale protection, which prevents lime flakes from falling out during ironing.

Steam generators Pro Express Ultimate and Pro X-pert Plus are equipped with the latest innovative developments from Tefal. The sole of the iron is made of durilium with the finest palladium coating.

During heating, a chemical reaction occurs, which performs the function of self-cleaning . During the chemical reaction, microscopic amounts of carbon dioxide and water are released, which do not harm health in any way.

Operational differences of Tefal steam generators

The company offers customers dozens of modifications of household steam generators. Each model has special advantages and disadvantages. Some devices differ from each other only by product code.

Let's look at the 4 most common series of steam generators from Tefal:

1. Express
2. Pro Express
3. Fasteo
4. Liberty

Express Series Devices

In this line, each model differs significantly from its competitors.

Do you like your steam generator?

Not really

Characteristics of devices by name:

• Express is the base model. There is no automatic adjustment of steam release, sprayer, anti-scale and self-cleaning of the sole.
• Compact Easy Control is one difference from the standard steam generator in this series. Ultracord system - convenient fastening and assembly of the power cord.
• Anti-calc - added automatic descaling of the device.
• Express Anti-calc Turbo - the standard set of functions is complemented by a Turbo button (short-term doubles steam generation throughout the sole). This mode helps to smooth out thick fabrics, eliminate wrinkles on clothes, and increase the efficiency of vertical steaming.

All generators in this line are equipped with an automatic shutdown system.

Pro Express Models

For the professional series Pro Express devices, the basic equipment contains: automatic steam control, double short-term steaming impulse, protection and descaling systems.

Models Specification:

• X-pert Plus - automatic cord winder and spray function.
• X-pert Control is a Power Zone function. Technologically, the release of steam differs in the area of ​​the double pulse. In the Express series, there is recoil over the entire area. In the Pro Express line, enhanced steam generation occurs only from the upper part of the sole holes.
• Express Care - anti-drip mode, button hole on the ironing plate.
• Ultimate - a system against the formation of drops on clothes and a control panel on the iron handle.

Fasteo models

The difference between the Fasteo line of economy-class generators and the Express and Pro Express series is that the steam pulse is 3 times weaker and the lack of automatic power selection for different types of fabrics. Also, the models do not have an “Anti-drop” mode, the cord length is shorter and the boiler volume is 0.1 - 0.6 liters lower.

Models Specification:

• SV6038 - no automatic shut-off, volume 1.2 l, steam boost 150 g/min, pressure 5.2 bar.
• SV6040 - increased impulse force (180 g/min), better Easygliding sole coating and 5.5 bar pressure.

The advantages of Fasteo steam generators are a large set of functions, light weight and reasonable price with relatively low power losses.

Liberty models

This series retains the same disadvantages as Fasteo, but with some exceptions. Differences between the Liberty line and previous economy class models:

• The power of the steam pulse is higher by 140 – 160 g/min.
• Availability of a hitchhiking system.
• Boiler volume 1.5 l.

Devices in this series are produced without the Anti-drop mode.

Liberty models specification:

• SV7030 - 5.5 bar, 310 g/min.
• SV7020 - 5.4 bar, 290 g/min.
• SV7010 - 5.3 bar, 300 g/min.

The main advantages of the series are increased power and convenience of vertical steaming due to a lighter design. At the same time, the devices remain in the affordable economy class category.

Precautions for use

You cannot use the device:

1. For treating surfaces not intended for cleaning with hot steam.
2. With a damaged electrical cable.
3. With wet hands.
4. In an explosive environment.
5. In conditions of increased dampness.

During operation, do not touch the main unit where the tank with the steam generator is located.

Do not direct the steam jet at exposed skin, other people or animals.

Care Tips

During use, scale accumulates in the steam generator, which negatively affects the operation of the device.

If the water in your region has high hardness, then it is necessary to descale the device every 50 operating cycles , or preferably more often. This procedure extends the life of the device.

To reduce scale formation, fill the tank with boiling water or use demineralized water.

The scale collection tank can only be removed after it has completely cooled down . Otherwise you may get burned. It takes a long time to cool down - 3-4 hours.

Tips for caring for the device

Preventive actions to maintain the steam generator in working condition do not require special knowledge and tools. First of all, you need to wait until the device cools down completely.

Caring for your iron and stand:

• When dirty, wipe the plastic elements of the generator with a soft cloth.
• Every 25 - 30 days of periodic operation, rinse the boiler twice with tap water.
• If the device is equipped with an anti-scale system, you need to unscrew the plug, remove the rod and rinse it.
• In models with an automatic “Anti-calc” system, cleansing is carried out by turning on this mode. Pressing the reset button the next time you start the device disables the anti-scale function. Some models are equipped with a collection brush, which also needs to be washed.

The method for cleaning the ironing plate depends on the type of coating:

• Duralumin spraying - remove plaque only with medium-hard sponges without metal threads.
• Stainless steel plate - the cleaning method is the same as the previous coating.
• Ceramic spraying and Easygliding self-cleaning system - only a soft cloth on a surface heated (cooled) to 38 - 40 ˚С.

When cleaning it is not recommended:

• Use household chemicals to clean plastic and metal parts.
• Rinse any parts of the device under running tap water.
• Use traditional means to remove limescale (soda, 9 - 70% acetic acid solution and other aggressive food products).

Proper cleaning and maintenance of the equipment guarantees a long service life.

Instructions and files

Advantages

Flaws

• There is no anti-scale system
• Lack of anti-drip system

I have long dreamed of buying such a device. I read the reviews, watched the video testing and decided to go with this model. The technology is powerful and a pleasure to work with.

Tefal fasteo sv6038e0

The Tefal sv6038e0 ironing system allows you to achieve incredible steaming results in a few seconds. The convenient and compact fasteo model gets the job done faster than its analogues thanks to its strong steam power .

descaling system ensures efficient ironing. For the sample, the manufacturer used a ceramic sole, ensuring the optimal temperature for all types of fabrics. Additionally, the steam generator included a vertical steaming function. It allows you to iron suits or curtains without using an ironing board.

Characteristics

Review of the Tefal Pro Express Ultimate GV9581 steam generator

The iXBT.com laboratory regularly receives devices intended for clothing care, including steam generators or steam stations. So now we will study the Tefal Pro Express Ultimate GV9581 steam generator. During the review, we will get acquainted with the advantages of the device, which the manufacturer identified as the main ones.

First of all, Tefal positions the steam station as a device that will allow you to professionally care for your clothes. The device is characterized by a powerful burst of steam and high pressure in continuous steam supply mode. A number of functions help you safely and comfortably care for clothing and fabrics of various compositions. During the experiments, we will see if the steam generator is as good as it looks when we first meet it.

Characteristics

Equipment

The box in which the Tefal Pro Express Ultimate GV9581 steam generator is located allows you to get a first impression of the device and its capabilities. The user can familiarize himself with the appearance of the device and its main functions. Information is presented primarily in English. However, much is clear intuitively or from pictures. Only one phrase has been found in Russian, and that is a slogan. The box is not equipped with any kind of carrying device.

Inside the package, the steam generator is securely fixed in two foam inserts. We discovered the device itself, consisting of a steam station and an iron attached to it. Also in the package was an iron part that looked like a fastener, and a set of documentation: a brochure “Safety Precautions and Rules of Use,” an international warranty card and a user manual.

At first sight

The design of the device is typical for steam generators of this type: the iron is connected to the base with a boiler using a steam hose. Streamlined shapes and a combination of white and gold colors visually lighten the dimensions of the device. The plastic is high quality, smooth, all parts and pieces of the device are tightly connected to each other. It is impossible to make a single justified complaint about the build quality - everything is really done carefully.

On the front of the steam generator we see a control panel with three touch buttons and two indicators. The power cable connects to the chassis at the bottom right side. In the same part there is a compartment for storing the cord. On the left side there is a steam hose that connects the iron to the station. During storage, the steam hose can be placed in the appropriate compartment running along the perimeter of the base.

A red screw cap is visible at the bottom of the side of the case. This is part of the flushing system that protects the device from scale. Under the lid there is a collector for collecting scale - a long narrow metal groove. The water tank is transparent, which will allow you to monitor the water level during operation. Its working volume is very large - 1.9 liters.

The iron stand is made of heat-resistant plastic and equipped with three rubber pads. In the upper narrow part there is a Lock System. To secure the iron to the base, you must first align the protrusion at the bottom of the stand with the groove in the base of the iron, and then move and click the lock, which will hold the nose of the iron motionless.

On the bottom of the device there are holes, apparently acting as ventilation holes, a sticker with brief technical information, and low legs.

The design of the iron is classic: a body with a sole and a handle with control buttons and indicators of the selected mode. The shape appears lightweight due to the color, design and thin support.

On the inside of the handle, exactly under the index finger, there is a steam button highlighted in red. The weight of the iron is rather average - it will be easy to iron, but you won’t be able to hold it there for a long time - your hand will get tired.

The connection between the steam hose and the housing is protected by a casing, which prevents damage to the hose. A length of 1.7 meters seems sufficient; We will be able to more accurately estimate this parameter only through practical experiments. The movement of the hose is limited by the hinge. In a vertical position, the iron is quite stable thanks to the stand at the bottom of the device.

The shape of the sole is triangular with rounded edges and corners and a narrowed top. The sole coating is ceramic, Durilium Airglide Autoclean technology. The surface of the sole is smooth, without nicks or scratches. Steam outlets are located both around the perimeter and in the middle of the sole. In the narrowed part of the spout you can see closely spaced steam outlets.

A metal part that looked like a fastener was found in the box with the device. It turned out that this accessory is intended for placing clothes during vertical steaming. The wide part is placed on, for example, a door, and hangers with clothes are hung on the hook.

A thorough examination confirmed the first impression of the device. The Tefal Pro Express Ultimate GV9581 steam generator is made with high quality and accuracy. The design is clear and simple, the iron is extremely elegant, the sole is smooth and equipped with a large number of steam outlets, the controls do not seem complicated. We will evaluate how convenient it is to work with a steam generator during experiments.

Instructions

A thick A6 brochure is devoted to safety measures and rules for using the device. The document is apparently intended for all countries where Tefal products are supplied, since the information is presented in a large number of languages. Moreover, the page numbers on which you can familiarize yourself with the desired option are not marked, so when searching for text in your native language, you need to look through the entire document. Information regarding safety and operating rules takes up only 4 pages. A section regarding the quality of water that can be used for the steam generator and a table listing possible problems, their causes and solutions may be useful.

Another document that looks like a comic is the user manual. There is practically no text in it, but the pictures explain all the processes and manipulations that need to be performed with the steam generator and the iron. We think that one viewing will be enough to start using the device. In the future, the document can be referred to when the user encounters a specific problem or task. And at this very moment a person realizes that studying information related to operation from pictures is not at all as easy and clear as it seemed at first.

To be fair, let’s say that operating the steam generator is simple and intuitive. Those points that may cause difficulties can be studied on the website - there the information is structured, given quite fully and presented in an understandable form.

Control

Controlling the Tefal Pro Express Ultimate Care GV9581 steam generator turned out to be very simple. After connecting to electricity, you need to turn on the device by pressing the corresponding button in the center of the control panel. Upon completion of work, pressing the same button turns off the device.

After turning on the steam station, the user sets the required operating mode. The selection is made by successively pressing the Mode button on the handle of the iron. By default, the device operates with Normal parameters. In any of the modes, steam is supplied by pressing the steam supply button, located on the inside of the handle exactly under the mode indicators. It’s easy to start and switch between operating modes, the buttons are conveniently located - Mode under the thumb, steam supply under the index finger.

During heating, the selected mode indicator flashes. Once the set temperature is reached, it begins to burn evenly.

At first we didn’t understand why the manufacturer indicated on the website that the iron was equipped with five steam generation modes. However, we later figured out that in addition to those indicated on the handle, Eco, Delicate, Normal and Max, a Boost mode can be added, the start button of which is located on the base.

If during work it is necessary to “give way to the park”, then pressing the Boost button starts a mode of increased steam generation for 15 minutes. This function is only available when the iron is operating in intensive mode. When the Boost function is launched, the iron automatically switches to Max mode, even if it was previously operating in another mode.

The device is perfectly controlled by three buttons: on/off, Boost function and Mode selection. But in trying to figure out the purpose of the OK button, we came across an interesting point, which we will describe below.

Two indicators inform the user that the boiler has run out of water or it is time to descale. We didn’t have time to bring the device to the point where it needed cleaning, but we were able to empty the boiler.

When the water runs out during ironing, the indicator lights up red and the iron stops heating. We concluded that ironing with an empty boiler is impossible and turned off the steam generator. Then we thought, perhaps the OK key resets the indicator and starts the iron working without water. However, subsequent inclusion did not confirm our assumption. The device turned on as if nothing had happened. We started the Booster mode and released the remaining steam, so that there was no water left anywhere - neither in the boiler nor in the steam generator system. However, the indicator did not light up, the iron continued to heat up, and when you pressed the steam button, it clicked ominously.

However, we think that under normal conditions the steam generator will not be subjected to such tests - the user himself is interested in a boiler filled with water. Moreover, to determine the degree of filling of the container, you do not need to wait at all for the indicator to light up.

Exploitation

Preparation for work is standard: remove the device from packaging materials, unwind the power cord and steam hose, place the steam station on a flat, stable, heat-resistant surface and fill the tank with water.

During the tests, we placed the steam generator on a specially designated area of ​​the ironing board. But let us clarify that the ironing board for testing is wide, and the area for placing the iron has an area of ​​42x27 cm. In this case, the base of the steam generator is placed securely and does not hang over any side. Do not place the housing on a soft surface or ironing board cover.

During operation, some parts of the steam generator become hot, so certain safety precautions must be observed. In particular, the steam generator cord, soleplate and stand for placing the iron are very hot. You most likely won't get burned, but you shouldn't touch these parts.

Before storing the steam generator, you should allow it to cool for at least an hour. Before carrying out care activities - at least two hours. Of course, no openings (filling or descaling) should be opened while the steam generator is operating.

For steam generation, you can use tap, bottled or purified water using household purifiers. If tap water is very hard, then it should be mixed with purchased demineralized water in a 1:1 ratio. Using unsuitable water can cause deposits to form in the steam chamber, which in turn will lead to stains on clothing and rapid failure of the appliance.

In general, we did not encounter any problems or difficulties during operation. The boiler is disconnected when moving towards itself and upward. Installed backwards, respectively, in reverse motion. The click helps you understand that the part is installed correctly and securely. It is filled with water without any special equipment - the hole is very wide in diameter. When draining, thanks to the design of the tank and the location of the drain holes, all the water leaves - not a drop remains in the boiler. Again, the user does not need to perform any particularly tricky manipulations for this.

The device is controlled simply. Heating modes and, accordingly, steam generation can be changed at any time with one click of the thumb. Moreover, the process is not only obvious, but also visual - the mode indicator flashes at the moment of heating and lights up exactly when the device reaches the desired temperature.

The coating of the sole is beyond criticism - perhaps we have never before dealt with an iron that glides over fabric so easily. The shape of the spout allows you to cope with the most difficult areas of clothing to iron out - folds, narrow places and similar unpleasant design features of clothing.

Steam is supplied only when you press the corresponding button. In order for the steam to flow continuously, you need to hold the button pressed. This did not cause us any inconvenience. In Boost mode, the steam comes out with a more powerful jet. The device takes some time for the steam to reach the desired pressure - at first it flows powerfully, then the supply force decreases. During this period, you can straighten your clothes - prepare, so to speak, a testing ground for further work.

Sometimes, when steam is applied, drops of water fall on the fabric. In this case, we repeated the dry iron over the wet area. Its power was enough to evaporate moisture stains. In general, when using the Boost mode, the fabric is slightly damp after processing. Therefore, after steaming and ironing, we hung the clothes on hangers or left them flat on the ironing board.

Vertical steaming takes place in Max heating mode and Boost function. There were no drops of water under the clothes being steamed or wet spots on the clothes themselves. The hook included in the kit is very convenient. So the user does not need to try to hang clothes in the bathroom on the curtain pipe and look for a place to install the steam generator. The main thing is to make sure that the surface of the door does not deform from exposure to steam.

The power cord and steam hose are long enough for comfortable ironing without extension cords or excessive cable tension. The cord does not touch the surfaces being processed at all; the steam hose, in general, does not crush the clothes being ironed.

The device is equipped with an automatic shut-off function. The system works regardless of whether the iron is standing on the base or vertically on the board. In the horizontal, i.e. working position of the iron, heating does not stop. Apparently, the manufacturer hopes that the user will not be so reckless as to leave the heated iron directly on the fabric.

Among the features, it should also be noted that the steam generator is convenient for ironing bed linen, since you can fold it several times with virtually no damage to the final result.

Based on the results of using the Tefal Pro Express Ultimate GV9581 steam generator, we can say that working with it is convenient, easy, pleasant and, most importantly, safe, subject to a number of obvious requirements. The device itself coped perfectly with all the tasks assigned.

Care

Maintenance of the steam generator is extremely simple. If you follow a few simple rules, this process will be infrequent and not labor-intensive.

• First, after each use, you need to drain the remaining water from the tank.
• Secondly, you need to start cleaning at least 2 hours after ironing, so that the device and all its parts are completely cooled down.
• Thirdly, it is prohibited to use any cleaning products: means for preventing or removing scale (vinegar, anti-scale agents) for washing the heating element and tank, as well as sole cleaners for the iron.

The plastic parts of the housing can be wiped with a slightly damp soft cloth. The iron sole provides good glide and steam distribution, and is also self-cleaning thanks to the catalytic coating: dirt is removed under high temperature.

The boiling tank must be serviced once a month or every 10 uses. The procedure is called pompously, but in reality it consists of unscrewing the lid of the boiling tank, removing the rod attached to it and rinsing it thoroughly. Then use a jug to fill the reservoir with tap water and gently shake the stand for a few seconds. Pour out the water. To obtain the best results or when using hard water, it is recommended to repeat the operation again. If the region has hard water, then the tank needs to be cleaned more often.

Our measurements

When simultaneously heating the soleplate of the iron and generating steam, the device consumes from 2580 to 2610 W. In idle mode - 1-1.4 W. When only the iron heats up - 840-900 W. Preparing for work does not take very long. So, in Normal mode, the indicator stops blinking after 1 minute 40 seconds. In Eco mode, preparation takes 1 minute 20 seconds.

The temperature of the iron sole was measured immediately after heating. Depending on the measurement point on the sole, the temperature was:

• Eco: 97-124 °C
• Delicate: 96—113 °C
• Normal: 104—135 °C
• Max: 111—171 °C

The temperature is highest in the middle and in the upper narrowed part of the sole. The lowest temperature was recorded in the wide base of the sole. However, the temperature spread in most modes is small.

The operation of the automatic shutdown system was also checked. The automatic shut-off function worked after 9 minutes 20 seconds while the iron was on the base. Left upright on the ironing board, the iron stopped heating after 9 minutes 45 seconds. When the auto shut-off function is activated, the on-off indicator begins to flash. Leaving the iron in a horizontal position, we waited 15 minutes; Automatic shutdown did not work. We didn’t dare wait longer, although the instructions say 38 minutes of waiting.

Practice tests

We will carry out standard tests to smooth out heavily wrinkled and overdried items, and also bring a raincoat and knitted jacket into decent shape using vertical steaming mode.

T-shirt with print

The item was both wrinkled and dry from long-term storage folded in the closet. The T-shirt is made of cotton jersey. Processed in “Eco” mode from the front side. Steam was supplied only periodically.

The fabric was easy to iron. The sole slid easily and just as easily smoothed out any creases that appeared. The print did not deform under the influence of temperature and hot steam.

Result: excellent.

Linen fabric

We sometimes use a piece of flax for photography or as a tablecloth for a small table. It is stored in a closet folded, so the fabric shows both specific wrinkles that are characteristic of untreated linen, as well as creases formed during storage.

We decided to try it in “Normal” mode. The fabric was smoothed out, but not well enough. Booster mode enabled. The iron automatically switched to “Max” mode, and things went much more fun. The steam was supplied by a powerful jet, which perfectly moistened the canvas and coped with the most difficult storage marks.

The fabric ended up being slightly damp, but it looked great.

Result: excellent.

Slacks

The trousers are made of thick cotton fabric that wrinkles easily. The slacks show obvious traces of spinning and drying.

We worked in the “Normal” mode at normal steam power. Steam was supplied almost continuously. They only paused to unfold and straighten their trouser legs. As a result, there were no traces of creases or wrinkles left on the fabric.

In this experience, we continued to admire the shape and smoothness of the iron's soleplate. The narrow top of the sole easily reached and smoothed the narrowest and most difficult to reach places. Already in the second experiment it became clear that there would be no problems with ironing shirts and men's shirts.

Result: excellent.

Mixed fabric shirt

The fabric is mixed, it clearly contains more than just cotton. The shirt is very warm and comfortable, although wrinkled a lot, it usually gets ironed out without any problems. In this test, we will check whether the soleplate of the iron leaves marks on the fabric, and in what mode the fabric can be processed without the risk of damage.

We chose the “Max” mode, turned on Boost and started ironing. The place where the iron passed immediately took on a well-groomed appearance. No traces of sole or shine appeared on the fabric. We switched the iron to “Eco” mode - the result was the same. From which we conclude that the device successfully and safely processes some types of mixed fabrics in both maximum and moderate heating modes.

The narrow nose and easy sliding of the sole made it possible to effortlessly smooth out sleeves, cuffs, areas around the armholes and collar.

Result: excellent.

Organza

As part of testing, we necessarily process organza. This is a test of the iron's ability not to deform synthetic fabric. The cut was wetted, twisted and tied into a knot. Although we dried the organza on a central heating radiator, the fabric did not reach an overdried state.

Ironed in the “Delicate” mode. Both the heating temperature and the steam power were enough to smooth out all the creases and jams.

Result: excellent.

Skirt made of suiting fabric with added wool

The skirt, although not straight, is not of a very complex design. But the fabric is very delicate - thick suiting with the addition of wool. When ironing it, there is a high chance of getting shiny stains. These are the kinds of fabrics that our grandmothers and mothers taught us to iron through damp gauze.

We processed the skirt from the wrong side in the “Delicate” mode. Steam was often served. The fabric was smoothed out effortlessly—one stroke of the iron was enough.

No shine, no deformation of the fabric - just a perfectly ironed skirt. The iron's nose easily reached the depths of the folds, and the steam straightened the fibers without damaging them.

Result: excellent.

Vertical steaming

Using the vertical steaming function, it was decided to smooth out a knitted pullover. The item is simply wrinkled from storage, without deep creases. We worked in Boost mode - increased temperature and steam power.

We attached the supplied hook to the door - by the way, an extremely convenient thing if you are not afraid of damaging the door covering with hot steam, and hung hangers with a pullover on it. We started working on the sleeves. We acted in the standard way: we straightened the part, pulled it slightly, brought the iron, holding it vertically in relation to the fabric, and pressed the steam button. The steam comes out in a very powerful jet, so you need to be careful not to accidentally burn your hand. In this way, we slowly processed the whole thing. When the power of the jet weakened, the next piece of the pullover was straightened. During these few seconds, the steam generator was ready to release the next portion of steam.

The pullover fabric was evenly moistened and stretched out perfectly. It took a little time to process - about two to three minutes.

Next, we decided to steam the freshly washed and dried raincoat. The fabric from which it is made is of very high quality, so after spinning the raincoat did not have a very wrinkled, but rather somewhat unkempt appearance.

Within five minutes we carefully steamed out all the light bruises. The look, of course, is not ideal, but after ironing the coat looks much worse - the seams of the lining, pockets and other structural details of the cut stand out and begin to shine. So vertical steaming is the only way to bring the item into decent shape without long and painful passes with your hands.

Result: excellent.

If we perceive vertical steaming as an additional, and not the main function, then its implementation can be considered quite good. The steam is supplied in a powerful jet, the pauses between blows are small, and the included hook eliminates the problem of finding a place to hang things. Powerful steam eliminates long-time steaming, so your hand does not have time to get tired from the weight of the iron.

conclusions

We liked the Tefal Pro Express Ultimate GV9581 steam generator, although the author of this article does not like ironing too much. Even if the user has a strong aversion to the iron and ironing board, but for some reason is forced to iron clothes frequently, then choosing this device will be a good decision. And those who love this process will undoubtedly experience more than one hour of pleasure from interacting with the steam generator.

The steam generator is easy to control and just as easy to operate. All processes go one-two-three: remove the water tank, fill it with regular tap water, select the desired mode, and automatically descale it. The automatic shutdown feature will turn off the iron's heating and steam generation if the user has forgotten to do so. We would also like to note the excellent manufacturing quality of the iron - the comfortable shape of the sole and the quality of its coating. In addition, the iron is equipped with a self-cleaning function, optimally distributes steam and, according to the manufacturer, is resistant to damage. We never ceased to be amazed at how easily the sole glides across any fabric. It is worth mentioning the rapid achievement of operating parameters. So, on average, the steam generator was ready for operation in less than two minutes. This is quite fast for this type of device.

The disadvantages include difficulties that could potentially arise before starting operation due to unclear instructions. The second remark concerns the operation of the device itself. Despite the fact that the steam generator is equipped with a “Drop Stop” function, during tests we repeatedly noticed drops of water on the fabric being ironed.

pros

• powerful steam supply
• easy and intuitive controls
• ease of care
• auto shut off function
• ease of gliding, optimal steam distribution and good shape of the iron sole
• quick readiness for work

Minuses

• unclear instructions
• at high temperatures drops of water fall on the fabric

In conclusion, we suggest watching our video review of the Tefal Pro Express Ultimate GV9581 steam generator:

Our video review of the Tefal Pro Express Ultimate GV9581 steam generator can also be viewed at iXBT.video

Tefal express 2912

The rating of the best model for ironing clothes opens with the express 2912. The small size of the boiler allows you to achieve the required level of pressure in just a couple of minutes . For long-term use, add water to the steam generator.

Characteristic

Advantages

• Automatic temperature adjustment
• Availability of a boiler tank

Flaws

• Lack of anti-drip protection

Recently, my usual household iron broke down, and I decided to buy a steam generator. I spent a long time comparing features and prices. As a result, my friend recommended the fasteo sample sv6038e0. When I found out all its characteristics and how much the sample cost, I bought it without hesitation. This is the best steam generator, convenient, heats up quickly. I didn't find any shortcomings in him. I recommend to everyone.

Tefal pro express care gv907

Tefal Pro Express is a powerful ironing device that does not leave stains or streaks. Such a device requires a special ironing board that can withstand the weight of the steam generator.

Tefal gv9070 has a double anti-scale system, and a built-in special collector prevents scale from getting on clothes. This system can significantly extend the life of the iron.

Characteristics

pros

Minuses

The iron is lightweight. Due to the strong steam, it thoroughly smoothes out wrinkles and there is no need to press the device tightly against the clothes. For a long time I could not understand how the iron worked, but everything was clearly explained in the instructions.

Tefal fasteo sv6040e0

without a boiler tefal fasteo sv6040e0 will provide high-quality and careful care of things Reviews about it are only positive. To smooth out hard-to-reach areas, the model had a specially shaped nose.

Fasteo sv6040e0 has a Smart technology that helps you quickly select the appropriate mode for a specific fabric.

Characteristic

Advantages

• Availability of energy saving mode
• A light weight

Flaws

I liked using the device. Despite the fact that the device is compact, it produces a large amount of steam. I'm pleased with the large water tank. There is no need to constantly add water. I pour it once every 30 minutes and during this time I have time to iron the curtains and washed clothes, of which there is quite a lot. An ordinary iron is forgotten forever, and I don’t want to return to it. I recommend this model to everyone, excellent price-quality ratio.

Tefal effectis gv6731

The rating of the best Tefal steam generators is completed by sample gv6731. It combines stylish design and quality. The model is equipped with a special eco-function that allows you to save up to 25% of electricity during operation . In addition to this, the manufacturer has built in an auto-shutdown function, in which the device independently understands that the ironing process is complete.

Characteristic

pros

• Vertical steaming
• Built-in eco function

Minuses

We bought an iron to replace an old broken one. Bought on sale for 10,000 rubles. I think that buying an iron for 19,000 is too expensive and there is no need for it. The device is excellent and smoothes out even the most stubborn wrinkles. I like that the sole does not burn and does not leave marks on clothes. The only downside is that it takes a long time to heat up. This steam generator is perfect for families with small children. Ironing with steam kills all germs.

What to look for when choosing?

When purchasing a device, there are many details to consider. Below we will tell you what to look for when choosing a device for steaming clothes.

1. Power. The more power a device has, the more energy it consumes. More powerful equipment can do the job faster and better.
2. Steam pressure is a very important function. The amount of steam produced by the device is directly related to pressure. For full operation, the equipment requires up to 7 bar of steam output.
3. Storage tank. If the volume of the container is small, then it is necessary to constantly fill it with water. This significantly slows down the ironing process.
4. The base of the steam generator is very important. Depending on the material of the sole, the quality of ironing changes. The aluminum sole has fast heat dissipation. To make such a sole stronger, manufacturers combine aluminum with other materials. For example, with stainless steel, which cools more slowly.
5. The advantage of any steam generator will be the presence in the device of additional functions and accessories that make fabric care easier.

Instructions: how to use a Tefal steam generator correctly?

After purchasing a steam generator, people have a question about how to use the equipment. The device comes with instructions for use, which clearly outline the rules for using the steam generator.

The work process includes several stages:

• First of all, water is poured into the tank and the heating is turned on.
• Next, mode and temperature for a specific material are selected.
• The last stage is ironing itself.

If the iron is left idle for 10 minutes, it will begin to cool down and the standby mode will automatically turn on. This is done to avoid fire.

How else can you use the device?

Hot steam destroys up to 70% of bacteria and allergens without the use of chemicals or sanitary products.

Steam generators can be used to clean carpets and large upholstered furniture from stains.

It is recommended to pre-treat stubborn stains with a cleaning agent , wait for the time specified in the instructions and treat with a steam generator. After each steam treatment, the stain should be wiped with a microfiber cloth.

Hot steam effectively cleans shiny stains, straightens creases on curtains, covers, frills and other decorative elements, refreshes and restores an attractive appearance.

Steam cleaning should not be used to remove protein stains.

Exposure to steam can restore shiny pile on suede shoes or jackets . After treatment with a steam generator, children's toys will not only be disinfected, but will also look like new.

House flowers enliven the interior, but a lot of dust collects on the plants, which is not easy to remove. Treating plants with dry steam effectively solves this problem.

The steam is directed from a distance of 50-50 cm and, thanks to the low humidity, cools quickly, so it does not burn the leaves . The flow power remains strong enough to knock dust off the leaves.

Steam generators are not equipped with additional components and are not intended for home cleaning. To clean floors, carpets, and kitchen surfaces, we recommend purchasing an additional steam mop or steamer.

FAQ: answers to frequently asked questions

Which is better, an iron or a steam generator?

If you have a large family and therefore a lot of ironing, a steam generator will make your job much easier.

How to descale a Tefal steam generator?

This is not necessary, but if desired, rinse the soleplate every 10 uses without using detergent or vinegar (this will ruin the device).

The steam generator is leaking.

It is necessary to select the type of fabric and set the temperature control and, in addition, turn on the steam function. This will help get rid of the leakage problem.

The steam generator has stopped producing steam, how to fix it?

Perhaps the valve in the iron does not work, which is due to a break in the wires in the iron sleeve. The device needs to be sent in for repair.

Safety precautions during operation

Equipment durability and safety depend on several conditions that must be observed.

While working, adhere to the following rules:

1. Straighten the steam hose and electrical cable. Twisting of elements is not allowed, because there is a possibility of overheating of the device and short circuit.
2. When working with the iron, the connecting cords should not cling to pieces of furniture.
3. The first heating is accompanied by the release of a specific odor. This occurs due to the initial heating of the steam generator thermoelements. The smell disappears with constant use.
4. The installation location is a durable surface that is resistant to heat and prevents the iron from tipping over.
5. The device stand and the iron itself must not be placed on the fabric part of the ironing board.
6. The design for horizontal steaming must be stable, with a wide base and working surface.

During active operation, it is necessary to carefully monitor the stable operation of the equipment.

If unusual noises or fluid leaks occur, the device must be turned off. After cooling, check all components and connections for integrity.

Best places to buy

It is better to buy steam equipment in household appliance stores. For example, in M.Video, Search or Eldorado . In such stores you will never be deceived or sold faulty equipment. In addition, they always provide a guarantee on the product they sell.

Another way is to purchase directly from the manufacturer through the official Tefal website. Such a purchase can bring benefits, since it is possible to get a discount by participating in promotions and sales. Also on sale is a beard and mustache trimmer, Xiaomi Robostock Sweep One, 8 best Tefal irons, an iron with a steam generator for the home. Additionally, a rating of the best cane strollers and the best Philips steam generators is presented.

Ordering a steam generator online from unfamiliar sites is not a good idea . When buying a device on the Internet, especially an expensive one, you will not be sure that it will arrive intact.

Where else can the device be used?

Devices with separate steam generation are ideal helpers in household chores. Even experienced housewives do not know some of the capabilities of these devices.

5 secrets of steam generators:

1. Iron dry and wrinkled fabrics.
2. It also works great with bedding folded several times.
3. He will put things and curtains in order without removing them from hangers and curtain rods.
4. The generator will clean items that cannot be ironed.
5. Will carry out antibacterial treatment of clothing and bed linen.

You can think of many ways to use the devices.

The main thing is to follow safety precautions and not violate operating conditions.