Heavy loads or intensive use for a long time of an Indesit automatic washing machine can lead to such troubles as bearing wear. The only possible way to correct such a problem is to replace it.
It is not difficult to determine that something is wrong with the bearing. You just need to listen to the sounds the washing machine makes when spinning at high speeds. A faulty bearing will definitely remind you of itself with extraneous noise or knocking.
You can unplug the machine and rotate the drum in different directions manually - characteristic sounds will confirm the “diagnosis”. Replacing a bearing is a rather labor-intensive process, but for people who have an understanding of working with various equipment and have the right hands, it will not be very difficult. So, everything in order. If you have any difficulties disassembling the equipment, then read the article - How to disassemble Indesit.
Common replacement mistakes
Please carefully study the following recommendations so that replacement does not become an expensive repair:
- the pulley is broken, you can’t pull it, just rock it slightly to the sides and pull lightly;
- breakage of the bolt heads; if the bolt does not fit, spray WD-40;
- break in the temperature sensor wire, be careful with the tank lid;
- the moving unit is damaged;
- The gasket of the moving unit has not been replaced;
- All sensors and wires are not connected during assembly.
So, you are convinced that replacement is quite a labor-intensive task, but doable if you have at least a little experience working with equipment.
If this process is difficult for you, we advise you to contact professionals, for example, an official service center; check the price on the website.
https://youtube.com/watch?v=uFpLe_Kd0NE
TOP stores of washing machines and household appliances:
- mvideo.ru/- household appliances store, large catalog of washing machines
- holodilnik.ru – Inexpensive store of household appliances.
- techport.ru - profitable modern online store of household appliances
- citilink.ru is a modern online store of household appliances and electronics, cheaper than offline stores!
- ru.aliexpress.com - spare parts for washing machines
Diagnosis of failure
It is necessary to first check and find out whether the washing machine needs to replace the bearings.
To identify malfunctions, you can rely on the main symptoms:
- The machine makes a louder noise than usual when spinning;
- During manual rotation, the drum begins to beat.
It is important to take into account that the machine can make noise for various reasons, and before diagnosing a malfunction in the bearing system, it is necessary to exclude factors such as foreign objects getting inside the device, and also make sure that the water intake and drainage system is working properly. In the case when the tested mechanisms operate without interference, we can assume that it is the old bearings that are causing the noise and it is necessary to begin replacing them immediately. In the case when the tested mechanisms operate without interference, we can assume that the old bearings are the cause noise and it is necessary to immediately begin replacing them
In the case when the tested mechanisms operate without interference, we can assume that it is the old bearings that are causing the noise and it is necessary to immediately begin replacing them.
Diagnosis of failure
Rumble and hum when the drum rotates in the washing mode, breakdown of the spin mode and rapid wear of the drive belt indicate a faulty bearings.
You can verify this by carefully inspecting the washing machine.
To do this, you need to open the door, grab the top of the drum with your fingers, try to swing it and determine whether there is play in the drum mount. And then spin the drum from the inside with your fingers, listen and try to catch extraneous noise.
If there is play, but there is no extraneous noise, this means that these parts have begun to deteriorate, but replacing them can be delayed for several months.
If there is play, and there are also characteristic noises (grinding, hum, rumble), but the drum rotates freely and does not stop, you need to change the bearings as soon as possible.
If the drum moves with a terrible grinding noise and even stops, it is generally dangerous to use this washing machine and requires urgent repairs.
Video
In the video below, you can once again familiarize yourself with the procedure for replacing the bearing on Indesit washing machines.
Mom,” wife and just a happy woman. She draws inspiration from travel and cannot imagine life without books and good films. She strives to become an ideal housewife and is always ready to share her experience.
Found a mistake? Select it and click the buttons:
In the 19th century, washing ladies' toilets took a lot of time. The dresses were first ripped open, and then each part was washed and dried separately so that the fabric did not become deformed. After washing, the clothes were sewn again.
For washing small items on the road or in a hotel, it is convenient to use a regular plastic bag. Socks or tights are kneaded inside a tied bag along with water and a small amount of detergent. This method allows you to pre-soak things and wash them without damaging the fabric or wasting a lot of powder and water.
There is a washing machine “for bachelors”. Linen washed in such a unit does not need to be ironed at all! The thing is that the device does not have a drum: some things can be placed inside the container directly on hangers (for example, jackets and shirts), and smaller things (for example, underwear and socks) can be placed on special shelves.
Washing machines equipped with the “No Iron” or “Easy Iron” functions can wash clothes with little to no wrinkling. This effect is achieved through a special approach to spinning - it is performed at low speeds, with long pauses, and a small amount of water is retained in the tank.
The first officially patented washing machine was made of wood and was a box with a frame, half filled with wooden balls. Laundry for washing and detergent were loaded inside and the frame was moved using a lever, which, in turn, made the balls move and grind the laundry.
The expression “soap opera” (“soap”) did not arise by chance. The very first series and shows that had a female audience were broadcast on television at a time when housewives did cleaning, ironing and laundry. In addition, to attract female viewers to the screens, commercials for detergents: soaps and powders were often played on air.
Astronauts, while in Earth orbit, solve the problem of dirty things using an original method. Clothes are dropped from the spacecraft and burn up in the upper atmosphere.
History knows the fact that a kitten fell into the drum of a washing machine and, after going through a full wash cycle on the “Wool” program, got out of the unit unharmed. The only trouble for the pet was an allergy to washing powder.
Washing machines have something to do with the origin of the expression “money laundering.” In the 1930s, American gangsters used a network of laundries as a cover for their illegal activities. By passing off the proceeds of crime as proceeds from cleaning clothes, they turned “dirty” money into “clean” money.
Bearings are important elements of a washing machine. They contribute to the controlled and silent rotation of the drum. Usually their breakdown is unnoticeable at the initial stage, so the user learns about problems with the bearing assembly much later, when an unnatural loud sound is heard during operation of the machine (especially during the spin stage). Ignoring the malfunction can lead to disastrous consequences: damage to the tank and complete failure of the unit. We'll figure out how to replace a bearing on an Indesit washing machine in our article.
Features of breakdown
If you follow the operating rules, you will need to replace the bearing no earlier than after 6 years of using the machine. It is after this time that the part is subject to natural wear and tear. Failure before the specified period indicates the influence of the following factors:
- Constantly overloading the drum. Imbalance of linen leads to increased load on the supporting part and accelerated wear of the part;
- deformation of the oil seal - a rubber sealing element that protects the bearing from moisture. If the seal is damaged, water washes away the protective layer and seeps into the bearing, causing corrosion and failure.
Constant overload of the drum can lead to rapid wear of the bearings
The main external sign of a bearing failure is increased hum, noise and vibration of the washing machine, and sometimes an unpleasant grinding noise during the spin cycle. You may also notice moisture appearing under the machine. If, when turning the drum manually, uneven rotation is felt, this indicates the formation of backlash - a gap between the drum and the tank. All of these signs indicate the need to replace the bearing on the Indesit washing machine.
How to replace
Before starting repair work, it is necessary to disconnect the machine from the electrical network in order to avoid the possibility of electric shock. After this, unscrew the water supply and drain hoses, pulling them forward a little.
Removing the pulley and motor
To solve the problem of wear of seals and bearings, remove the motor and pulley of the washing machine. To do this, you must first remove the drive belt by screwing the pulley and pulling the belt forward.
After this, secure the pulley by inserting a strong pin into it. You can tighten the pulley if you unscrew the bolt that secures it. The pulley is removed from the shaft if you swing it a little and pull it towards you. In this case, it is not necessary to dismantle the heating element. Although, this is the time to consider the condition of the heating element. If there is a thick layer of scale on it, it is better to remove it.
The engine can be removed by unscrewing the bolts that secure it. In this case, you need to remove the pipe. It is easier and easier to do this through the bottom of the machine, turning it on its side.
Removing the top cover
On the back of the machine there are 2 self-tapping screws, through which the cover is attached to the body. By unscrewing them, the lid will move back a little. After this, it can be lifted and removed.
Some models of the Indesit washing machine are equipped with special plastic latches that secure the lid. In this case, it is enough to unfasten them, which will allow you to remove the top cover.
Removing the Drum
The next step in replacing the oil seal and bearings is to dismantle the drum. To do this, you need to remove and pull out the tank by pulling it forward. All Indesit models are equipped with a one-piece tank. In order to be able to access the drum, you will have to divide the tank into 2 parts. This can be done by sawing it using a grinder or a metal saw.
Before you start cutting the tank, you need to make a final decision on how its subsequent assembly will be carried out. To do this, you need to make several holes on its surface for bolts, with the help of which the tank can be assembled into a solid structure.
After disconnecting the drum from the tank, experts recommend inspecting it for damage. In addition, you should check the condition of the gasket located under the drum. If it is stretched and has cracks on the surface, it is better to replace it.
Removing and replacing bearings
Now it's time to change the oil seal, which performs a protective function for the bearings. To do this, you can use a screwdriver to pry off the seal. It is possible that this will be difficult to do. You will have to use a hammer and chisel, carefully knocking out the bearings by tapping them in a circle.
If it is impossible to do this yourself, you will have to contact a service center, where, using special equipment, the cuff will be pressed out of the bearings.
After successfully removing the cuffs and bearings, you need to clean and lubricate the place where the new parts will be installed. It is recommended to use a special sealant for lubrication.
Purchased new bearings and a cuff can be installed in their original place using a hammer and a wooden block. As a result, it will be possible to significantly soften the force of the hammer impact, preventing cracking of the bearings and damage to the seal. It is recommended to direct the main direction of impact towards the edges of the parts. The oil seal must rest on bearings. After this, all that remains is to reassemble the Indesit washing machine in reverse order.
To ensure that replacement does not cost too much, it is recommended to adhere to the following operating rules:
- Operations with the pulley must be performed carefully, without sudden jerks. You first need to lightly swing it to the sides and then pull it forward. Otherwise, the pulley may be broken;
- When using the machine for a long time, its bolts may become stuck, which makes it difficult to unscrew them. If you apply force when unscrewing the bolts, you can tear off their heads. To avoid this, spray them with WD-40;
- when dismantling the tank cover, the wires of the temperature sensor can be broken;
- You should assemble the washing machine carefully, not forgetting to connect all the sensors.
Following these simple rules will help you avoid additional costs for repair work.
Bearing replacement: procedure
To get to the bearings, you need to disassemble the washing machine body and remove almost all the parts.
Dismantling parts
In order to remove the top cover of the washing machine, you need to unscrew the two bolts securing it from the back. The panel is moved back a little and raised up. In some models of Indesit washing machines, the front part of the lid is secured with plastic latches. You can remove the part from such latches if you give a few light blows to the cover in a direction away from you.
To dismantle the dashboard , you need to remove the detergent compartment by pressing the latch in the center. In the resulting niche, unscrew several bolts securing the dashboard. It is removed from the latches and, having disconnected the wires, put it aside.
Repair of the unit begins with dismantling the top cover and dashboard
Removing the back panel is easy - you just need to unscrew the six bolts from the back wall and move it to the side. The belt connecting the pulley to the engine may interfere with further manipulations, so it should be carefully removed.
After dismantling the rear panel, remove the belt from the pulley
At the top of the washing machine there are: a counterweight, a pipe connecting the powder compartment to the tank, a water intake valve and its contacts, as well as a pressure switch, its tube and contacts. All these parts should be removed.
The location of the parts and the connection diagram of the contacts can be photographed so that after the repair you can quickly and correctly reassemble the washing machine in the reverse order.
Before removing the front panel , you need to remove the hatch door and rubber seal from it. Dismantling begins with the cuff - it is bent with a screwdriver and carefully removed. The door is removed by unscrewing several bolts that hold the hinge.
If you unscrew the bolts holding the hinge, you can easily remove the hatch door
In order to remove the front panel, just unscrew the bolts that secure it.
At the bottom of the installation, you need to dismantle the electric motor, heating element, counterweight, drain pipe and shock absorbers. You need to remove the power supply and ground wire from the engine, and then unscrew the bolts securing it. Also disconnect the heating element wiring.
To remove the engine, you need to unscrew the bolts holding it
To get to the shock absorbers and drain pipe, you need to lay the washing machine on its side. Using pliers, remove the clamp and disconnect the drain pipe from the pump. Then unscrew the shock absorbers.
Shock absorbers are disconnected at the bottom of the washing machine
After dismantling all the parts, all that remains is to remove the tank. The collapsible part will consist of two parts, bolted together around the circumference. You can see the one-piece tank in the photo below.
In the photo you see a non-separable washing machine tank in which the drum is located
The washing machine drum rotates using a shaft that passes through its back wall through a bearing, then exits through the tub and is connected to a pulley from the outside. To get to the bearing, the pulley must be disconnected . It is better to use a T40 hexagonal star wrench and loosen the bolt, gradually loosening it. If the part does not give in, spray it with WD-40.
In order to unscrew the bolt securing the pulley, you need to use a T40 hexagonal star wrench.
To get to the drum and the bearings located in it, you need to disassemble the tank . In the collapsible part, simply unscrew the bolts, and the solid tank needs to be cut as shown in the photo below.
First of all, using a drill, holes are made around the perimeter of the weld at a distance of approximately 5 cm from each other. When assembling the tank, these holes will be needed for fixing with bolts.
Then comes the most important thing - using a hacksaw for metal, the tank is carefully sawed along the seam. It is better to do this as carefully as possible so as not to spoil the part.
Then unscrew the bolts attaching the drum to the tank, unfasten the latches and remove the tank wall. Now you can begin replacing the bearings in the drum.
Replacing bearings
How to change a bearing? First you need to remove the old oil seal from the socket, then knock out the metal washers. Start with a larger outer bearing. The drum is laid with the hatch opening down, the chisel is placed on the outer rim of the metal ring and hit with a hammer. The inner bearing is removed in the same way.
When replacing bearings, it is important not to damage the drum housing, so be careful that the bit does not come off while knocking out the bearing.
The freed sockets are cleaned of dirt and rust, treated with WD-40 and lubricant. New parts are driven into place, hitting only the outer edge. The bearings must fit into the sockets all the way.
The bearing is driven into the seat using a hammer and chisel
The oil seal is placed on the inside of the tank, having been pre-treated with lubricant.
The oil seal is treated with lubricant before installation.
Now you need to assemble all the parts of the washing machine in reverse order.
We will be glad if our article helps you successfully replace the bearing on your Indesit washing machine. Proceed carefully, follow the operating instructions for the equipment and do not overestimate your capabilities! Good luck!
The nuances of performing work on machines from different manufacturers
To repair some models from individual manufacturers, you need to know about the nuances determined by the design of these units. Washing machines of such brands as Indesit and LG, Samsung and Atlant have such features.
"Indesit" (Italy)
When repairing cars of this brand, it is initially necessary to clarify the design of the tank, because it may be different. New models are produced with a non-separable tank, and older ones with a collapsible one.
This determines the volume and sequence of operations performed. In addition, on some models the pulley mounting screws may have left-hand threads (W 84 TX), which must be taken into account.
If the brass bushing installed on the axis of the drum cross is damaged, it must also be replaced when performing such work. Also, models of this brand provide for double fastening of the drum axis, which is a certain nuance that should be remembered. The presence of a self-positioning sensor, which must be turned off when dismantling the drum, is another feature that you should know when doing the work yourself.
"LG" (South Korea)
For washing machines from this manufacturer, the tank is removed from the front of the device body. Modern models of this brand have improved technical characteristics that allow you to wash a significant amount of laundry in one load. Therefore, such devices are equipped with a tank that is quite heavy, which makes it somewhat difficult to carry out the work described.
In addition, when disassembling the drum, you should pay attention to the mounting unit for the electric motor, which is somewhat different from the type of mounting used by other manufacturers.
Samsung (South Korea)
The design of washing machines of this brand also involves dismantling the tank through the outer wall
When working with Samsung washing machines, you should be especially careful when knocking out the bearing, because If the bushing is damaged, the entire drum will have to be replaced. In addition, a distinctive feature of this brand is the use of two bearings of different sizes on one shaft
In this case, the larger one is knocked out from the outside towards the tank, and the smaller one from the inside.
In addition, a distinctive feature of this brand is the use of two bearings of different sizes on one shaft. In this case, the larger one is knocked out from the outside towards the tank, and the smaller one from the inside.
"Atlant" (Belarus)
For machines of this brand, the drum is removed from the rear side, which is provided for by their design. The tank on Atlant brand machines is of a collapsible type, so there is no need to saw it when replacing bearings.
When assembling the tank, it is necessary to use a sealant, this will provide more reliable protection against leakage.
The need for timely repairs
Traditionally, horizontal loading washing machines use two bearings. These support elements hold the washing machine drum in place, keep it horizontal and rotate freely.
Both bearings are mounted on the same shaft and are sealed from water ingress by a seal on the inside of the drum. Meanwhile, wear of the existing seal after some time of operation of the device leads to water seeping into the area of the front bearing.
Replacing the support bearings of the working shaft of the washing machine is one of those serious malfunctions that requires time, a search for components, and the hands of professional performers to eliminate.
As a result, bearing parts corrode, rust and eventually fail. The drum does not rotate, loses balance, and jams. It’s better not to let it get to this point - you should change the bearings and carry out other repairs on the washing machine in a timely manner (when noise appears).
Indesit washing machines of the latest generations are equipped with a self-diagnosis system, which greatly facilitates and speeds up the identification of existing and impending breakdowns. Machine owners need to know error codes. Decoding them will help you understand whether you can repair it yourself or whether it’s better to go to a workshop.
We carry out repairs: step-by-step instructions
First, you need to correctly remove the front and back walls of the Indesit washing machine without damaging any of the sealing rubber. First, remove the top cover of the Indesit washing machine by unscrewing several bolts. After this, removing the back wall is not difficult, just unscrew a few fasteners, but with the front wall the situation is more complicated. How to remove it correctly?
- First, we remove the powder cuvette of the washing machine, which you need to pull towards you until it stops, then lift it up and pull it out.
- We find and unscrew the fasteners that hold the front panel.
- Now we have access to all the screws holding the front wall of the washing machine, unscrew them.
- We remove the rubber cuff, then remove the bolts holding the hatch blocking element and dismantle the front wall of the washing machine.
So, we have access to the “insides” of the Indesit machine. Now replacement of oil seals and bearings will be carried out freely. First of all, you need to remove the belts from the drum pulley and motor drive. Then you need to securely fix the pulley by inserting a block of wood into it and unscrew the main fastening element that holds this drum pulley.
The next step is very important; you need to carefully pull off the drum pulley. The fact is that it sits quite tightly on the axis along with the drum, and if you try to tear it off with tools, you can easily harm it. If the drum pulley was successfully torn off, you can begin dismantling the spacer bar. Next, unscrew the fastening elements of all counterweights and carefully pull them out.
We disconnect all wires from the electrical elements of the washing machine, and then unscrew the fastening elements of the moving drum assembly. Most likely, the screws will be rusty and “stick” to the metal, so before unscrewing you need to spray them with WD-40.
We proceed to the next important stage - disassembling the drum and replacing damaged parts. Here you need to adhere to a strict procedure.
- Remove the clamps that hold the tank cover.
- Carefully remove the seals and the lid covering the tank.
- We take out the drum along with the moving unit where the bearings are located.
- We check the gasket on which the moving unit rests; if the rubber has deteriorated, then you need to throw away the old gasket and replace it with a new one.
- We load the moving part with the remains of the drum into the car and take it to the nearest car service center, where we ask the mechanics to press out the bearings. It is possible to do this work on your own, but it is very risky, because this requires skills + equipment that we do not have.
- We install new bearings and seals, and then reassemble the Indesit washing machine in the reverse order.
By the way, there are a lot of good videos about assembling and disassembling a washing machine. And if you are interested in information about the features of replacing bearings in washing machines of other brands, then this article will help you.
Mistakes made during replacement
As part of this paragraph, we decided to outline the warnings of specialists regarding all stages of repairing an Indesit washing machine. Some errors can be easily corrected, but some are too expensive and lead to the need to replace entire units of the “washing machine” being repaired. What typical mistakes do our “homemade” people make and how to avoid them?
- They break the pulley trying to pull it off the drum axis. To remove the pulley, you need skill; force will not help the matter, you can only do harm. Try rocking it from side to side and pulling at the same time. But under no circumstances hammer along the axle.
- The heads of the fasteners are torn off. If one of the bolts could not withstand your pressure and broke, this is not a fatal mistake on your part, but it will require additional fuss. You will need to drill out the broken bolts and then cut new threads in the seats.
- They break the temperature sensor, including breaking its wire. There is only one recipe for this problem - be careful with the tank cap. Otherwise you will have to buy a new temperature sensor.
- Damage to the moving unit during artisanal pressing. In this case, we have already advised you to contact a car service, because doing this work with improvised means is 10 times more difficult.
- They forget to replace the gasket on which the moving unit is located. The carelessness of the technician who looked at the rubber gasket may result in repeated repairs of the moving unit.
Replacing a bearing when repairing a top-loading washing machine
A distinctive feature of top-loading washing machines is that the drum is attached to the body on two axle shafts, and not on one, as in the models discussed earlier. In this case, the bearings are changed on both axle shafts at the same time, regardless of which one has failed. Work on units of this type is carried out as follows:
- The outer and rear walls of the machine are removed.
- Electrical wires and hoses that could interfere with work are disconnected.
- The linings located on the sides of the drum, under which the calipers are located, with the bearings installed in them, are removed.
- The bearing on the side where there is no pulley is changed first, then on the opposite side.
- The seats are cleaned and lubricated before installing a new bearing.
- The units are assembled in the reverse order of disassembly.
Important! On the side where there is no pulley, the thread securing the caliper is normal, right-handed, and on the side where the pulley is installed, it is left-handed.
Replacing bearings in Indesit washing machines
The bearing and oil seal are important parts of Indesit washing machines. The efficiency of the entire unit, the correct execution of the washing program depend on their operation, and the integrity of the oil seal determines the protection from moisture of many other parts of the mechanism.
The bearing is placed on the shaft of the crosspiece that rotates the drum and ensures its free rotation in the tank opening.
The seal serves to seal and seal. It is made of a special material that does not allow water to pass through.
If both of these components or one of them begin to fail, you need to replace them as soon as possible, taking into account the design features of Indesit washing machines. Otherwise, at one point the drum may stop spinning completely.
Preparation of the workplace
To replace a bearing in an Indesit washing machine, you first need to stock up on new bearings and an oil seal corresponding to the model that needs to be repaired. By the way, wear of the oil seal may be the main cause of problems with the bearing.
The best option is to use original components. Next we deal directly with the washing machine. To replace a bearing in a washing machine, you will have to remove its tank, which Indesit’s evil and mercantile designers of this brand managed to make monolithic.
For what? Yes, so that instead of replacing the bearing, you would have to change the whole block along with a new tank. And this “pleasure” will cost a lot (at least half the cost of the entire car). This option does not suit us! Why pay extra money?
We will limit ourselves to only replacing the bearings and oil seal. Well, let's turn directly to the washing machine. You will have to almost completely disassemble it. Therefore, you should be located where there is enough space and nothing will interfere with the process. Well, prepare the necessary tools.
Replacing bearings for an Indesit washing machine
When choosing bearings for a washing machine in a store, take the worn parts with you first so as not to miss. If you buy online, make sure that the selected bearing actually fits your Indesit. Prices can also be found on the Internet or by phone.
It is important that you need to buy not only the bearing itself, but the entire set: two bearings and two seals, they need to be replaced together, otherwise the replacement will soon need to be repeated.
Tools for disassembling the Indesit washing machine
Replacing the bearing of an Indesit washing machine with your own hands is not so difficult. The main thing is to get the bearings themselves, which will require disassembling the entire machine. Please be patient and have the following tools:
- Phillips and flat screwdrivers;
- socket and open-end wrenches;
- hammer;
- bit;
- hacksaw;
- pliers;
- WD-40 lubricant;
- glue and finally replacement parts.
What bearings are included in the Indesit SMA? Symptoms of a problem
It must be said that the main reasons for wear of moving components are improper operation and natural wear. So that you can avoid unpleasant breakdowns in the future, we list these reasons:
- Drum overload with laundry. If your washing machine is designed for a load of 5 kilos, this does not mean that you need to fill it to capacity. Correctly load 2/3 of the total volume of the drum. Otherwise, the parts are subject to increased load, which leads to rapid failure.
- Incorrect housing installation. When the MCA is not level, it shakes violently during the spin cycle and the vibration increases. All this negatively affects the moving parts of the machine. Make sure that the washer is stable on the surface.
- Seal wear. Manufacturers claim that the oil seal service life is on average 5 to 6 years. When the O-ring loses its seal and leaks, water washes away the lubricant, causing the internal components on the shaft to begin to wear out.
Before replacing a part, select a new replacement. So, for the Indesit models IWSB 5085, IWSC 5085, bearings with different serial numbers can be used. To figure out which SM is suitable for your SM, look at the table.
You can find out how much a repair kit costs on the Internet or on the manufacturer’s website. It is best to select original spare parts. They will definitely fit your model. The kit includes 1-2 bearings and an oil seal. All elements are replaced at once, otherwise there is no point in carrying out repairs.
The wear of the driving units on the shaft is difficult to confuse with something else. Its companions are creaking and grinding sounds when the drum rotates. There may be signs of wear on the back wall of the tank. Let's start disassembling.
Replacing the bearing in the drum of an Indesit washing machine with your own hands
Before changing a part, prepare for disassembly. What tools are needed:
- Phillips and slotted screwdrivers.
- Open-end wrenches.
- Socket heads and wrenches.
- Wooden block.
- Bit.
- Pliers.
WD-40 fluid will also come in handy. It will help deal with stuck fasteners.
Replacing the bearing of an Indesit washing machine requires complete disassembly of the equipment. For this you need free space. If it is not possible to take the machine to the garage, then move the body to the center of the room.
- Remove the plug from the outlet, unplugging the machine.
- Close the water supply valve.
- Disconnect the inlet hose from the housing. Immediately place it in a sink or container to drain the water.
Place the SMA in the center of the room. Take out the powder dispenser because moisture will accumulate inside it. Also remove the drain filter.
It is located under the loading hatch. Wait for the liquid to drain and proceed to disassembling Indesit IWSC 5105, WISL 102.
